sammy909 Geschrieben 17. Juni 2007 Melden Share Geschrieben 17. Juni 2007 So, ich hab jetzt nach einigen Schwierigkeiten ein Bootlog gemacht, glaub ich, kann ich nur nicht finden. Soll in der Zwischenablage liegen, aber wie finde ich die. Obwohl das Problem beim Bootlog nicht aufgetreten ist??? Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 17. Juni 2007 Autor Melden Share Geschrieben 17. Juni 2007 Armes Deutschland... Den Inhalt der Zwischenablage findest Du, wenn Du z.B. hier beim Verfassen Deines Beitrages dann die Taste STRG gedrückt hältst und dann zusätzlich V bedienst. Oder einen Rechtsklick und "Einfügen"... ne Windoof-Bedienungsanleitung muß ich aber nicht noch verfassen? Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
sammy909 Geschrieben 17. Juni 2007 Melden Share Geschrieben 17. Juni 2007 Warum tritt das beim Bootlog nicht auf. Muß ich noch was umstellen, das Original kommt mir länger vor. debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: BMon V1.0 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID debug: HWrev X5 SWrev 0.81 debug: B/Ex/Fl(MB) 16/16/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS debug: Got Block #0032 will verify ELF image, start= 0x800000, size= 154948 verify sig: 262 Branching to 0x40000 U-Boot 1.1.4 (Tuxbox) (Apr 10 2006 - 22:44:42) CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache *** Warning: CPU Core has Silicon Bugs -- Check the Errata *** Board: DBOX2, Nokia, BMon V1.0 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB Scanning JFFS2 FS: .... done. FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 ### FS (squashfs) loading 'vmlinuz' to 0x100000 ### FS load complete: 696900 bytes loaded to 0x100000 ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 696836 Bytes = 680.5 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.32-dbox2 (image@tower) (gcc version 3.4.4) #1 Do Aug 31 20:09: 34 CEST 2006 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs Decrementer Frequency = 252000000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0) Console: colour dummy device 80x25 Calibrating delay loop... 66.96 BogoMIPS Memory: 30776k available (1184k kernel code, 348k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. Squashfs 2.2-r2 (released 2005/09/08) © 2002-2005 Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:13:e4:af loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank Intel/Sharp Extended Query Table at 0x0035 cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00540000 : "root (squashfs)" 0x00540000-0x007e0000 : "var (jffs2)" 0x007e0000-0x00800000 : "FLFS (U-Boot)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.1.3 (2006.08.31-18:14+0000) multi-call mount: Mounting /dev/mtdblock/2 on /var failed: No such file or director Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
sammy909 Geschrieben 17. Juni 2007 Melden Share Geschrieben 17. Juni 2007 Noch einer debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: BMon V1.0 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID debug: HWrev X5 SWrev 0.81 debug: B/Ex/Fl(MB) 16/16/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS debug: Got Block #0032 will verify ELF image, start= 0x800000, size= 154948 verify sig: 262 Branching to 0x40000 U-Boot 1.1.4 (Tuxbox) (Apr 10 2006 - 22:44:42) CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache *** Warning: CPU Core has Silicon Bugs -- Check the Errata *** Board: DBOX2, Nokia, BMon V1.0 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB Scanning JFFS2 FS: .... done. FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 ### FS (squashfs) loading 'vmlinuz' to 0x100000 ### FS load complete: 696900 bytes loaded to 0x100000 ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 696836 Bytes = 680.5 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.32-dbox2 (image@tower) (gcc version 3.4.4) #1 Do Aug 31 20:09: 34 CEST 2006 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs Decrementer Frequency = 252000000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0) Console: colour dummy device 80x25 Calibrating delay loop... 66.96 BogoMIPS Memory: 30776k available (1184k kernel code, 348k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. Squashfs 2.2-r2 (released 2005/09/08) © 2002-2005 Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:13:e4:af loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank Intel/Sharp Extended Query Table at 0x0035 cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00540000 : "root (squashfs)" 0x00540000-0x007e0000 : "var (jffs2)" 0x007e0000-0x00800000 : "FLFS (U-Boot)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.1.3 (2006.08.31-18:14+0000) multi-call mount: Mounting /dev/mtdblock/2 on /var failed: No such file or directory event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ Detected STB: Vendor: Nokia Model: D-BOX2 [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 $Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $ $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $ avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $ avia_gt_core: autodetecting chip type... GTX avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $ avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $ avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $ avia_gt_core: masking unhandled irq reg 1 bit 11 avia_gt_core: masking unhandled irq reg 1 bit 13 avia_gt_ucode: loaded ucode v001A avia_gt_ucode: ucode section filters disabled. avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning... avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $ avia_gt_gv: set_input_size (width=720, height=576) avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $ avia_gt_pcm_set_rate(44100) avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $ avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $ avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $ avia_gt_core: Loaded AViA eNX/GTX driver avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $ avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) Console: switching to colour frame buffer device 82x32 avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $ avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $ avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $ avia_gt_pcm_set_rate(44100) avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $ DVB: registering frontend 0:0 (VES1893)... avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $ avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $ avia_gt_proc: $Id: avia_gt_proc.c, v 0.1.3 2005/12/11 22:30:00 Skars & Merandos Exp $ avia_gt_proc: Description: GTX/ENX proc_dev Driver with proc_fs extension options: (demux reinit) enx_reset=1 (framer chan.) fc_reset=1 (clr avia reg) avia=0 (enx td trace) trace=1 (lock, unlock) spinlock=0 Schreiben ueber /proc/bus/gtx (delay) delay=500 Starting the automounter Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970 $Id: sectionsd.cpp,v 1.227 2006/06/08 20:19:32 houdini Exp $ [sectionsd] Caching max 6000 events [sectionsd] Caching 14 days [sectionsd] Events are old 60min after their end time /var/plugins/operations logcs_init /var/plugins/operations camd_init Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 17. Juni 2007 Autor Melden Share Geschrieben 17. Juni 2007 Da fehlt trotzdem noch etliches im Bootlog. Die interessanten Meldungen kommen am Ende (Laden der Kanallisten, erster Zap-Vorgang vom Start der Box her etc.), das fehlt hier alles... Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
sammy909 Geschrieben 18. Juni 2007 Melden Share Geschrieben 18. Juni 2007 Und wie komm ich daran, möchte Freitag weitermachen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
DeepBlue2000 Geschrieben 18. Juni 2007 Melden Share Geschrieben 18. Juni 2007 hi, hab gehört es gibt einen neuen Philips Tuner Treiber der auch auf Sagem laufen soll, der das Prob bei ISH mit QAM256 etwas besser lösen soll. hab so BER Werte mit meiner schwarzen Sagem zwischen 40.000 bis 70.000 bei den Privaten RTL/SAT1 usw... nun die frage, wo gibts den und wie bindet man den am besten ein ? [edit] hab mir mal das GLJ Image geflashed....und die BER Werte liege da bei 10.000 die scheinen anderen Tuner Treiber zu haben....aber wie find ich das raus ich will kein GLJ nutzen.... [/edit] Keywelt rulez gruss Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
diver Geschrieben 18. Juni 2007 Melden Share Geschrieben 18. Juni 2007 Hi Leute Hab´am Sontag mal das V1 beta 6 und das root update in die Box geflasht (wegen ide unterstützung) hatte vorher das beta 5 Nun ist mir ´ne Kleinigkeit aufgefallen : Lautstärkeregelung und Mute -Taste meiner Nokia Sat 2xi sind ohne Funktion hat vieleicht jemand ´ne Idee ?? Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
stachi Geschrieben 19. Juni 2007 Melden Share Geschrieben 19. Juni 2007 @diver das sagt die Suchfunktion: Klick Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 19. Juni 2007 Autor Melden Share Geschrieben 19. Juni 2007 @DeepBlue2000 Ein Philips-Tunertreiber wird auf einer Sagem Kabel nie funktionieren und auch gar nicht erst geladen. Die Sagem hat eine völlig andere Tunerbestückung... @diver Was bitte willst Du in einem noHDD-Image mit dem Root-Update der HDD-Version? Flashe Dir das HDD-Image, und fertig. Anders bekommst Du nur Probleme und hast am Ende ein Image, bei dem nichts zusammenpaßt... Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
stachi Geschrieben 19. Juni 2007 Melden Share Geschrieben 19. Juni 2007 oh man das da V1 steht hab ich kommplett überlesen Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Stahlsi Geschrieben 20. Juni 2007 Melden Share Geschrieben 20. Juni 2007 Hallo, Ich habe das neue Keywelt Image V1 Beta6 auf meine Box gespielt und möchte damit eine Festplatte 250GB laufen lassen. Die Festplatte ist Formatiert,wird aber nicht gemountet. Warum !!??? Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
stachi Geschrieben 20. Juni 2007 Melden Share Geschrieben 20. Juni 2007 weil das V1 ohne hdd unterstützung ist, guck mal nach V2 Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Frankie7878 Geschrieben 22. Juni 2007 Melden Share Geschrieben 22. Juni 2007 Hallo ! Also aktuell habe ich auch das Problem das meine Nokia Box (2*500) nach den starten immer die Meldung "kein Kanal" anzeigt, nach den Umschalten läuft es direkt wieder . Ohh ich hoffe mal ich hab das richtigen Thread erwischt, da ich die Aktuelle April Version drauf habe . Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
dietz Geschrieben 22. Juni 2007 Melden Share Geschrieben 22. Juni 2007 Hi Hab das gleiche Problem mit 2Sagemboxen und dem neuesten keyweltimage(Kabel).Immer beim hochfahren, egal welcher Sender,kommt Kanal nicht verfügbar.Nach dem umschalten läuft alles ohne Probleme.Weiss jemand woran das liegen könnte? Gruss Dietz Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
sammy909 Geschrieben 22. Juni 2007 Melden Share Geschrieben 22. Juni 2007 Hi, noch ein Bootlog... Sending SIGKILL to all processes. The system is halted. debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: BMon V1.0 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID debug: HWrev X5 SWrev 0.81 debug: B/Ex/Fl(MB) 16/16/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS debug: Got Block #0032 will verify ELF image, start= 0x800000, size= 154948 verify sig: 262 Branching to 0x40000 U-Boot 1.1.4 (Tuxbox) (Apr 10 2006 - 22:44:42) CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache *** Warning: CPU Core has Silicon Bugs -- Check the Errata *** Board: DBOX2, Nokia, BMon V1.0 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB Scanning JFFS2 FS: .... done. FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 ### FS (squashfs) loading 'vmlinuz' to 0x100000 ### FS load complete: 696900 bytes loaded to 0x100000 ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 696836 Bytes = 680.5 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.32-dbox2 (image@tower) (gcc version 3.4.4) #1 Do Aug 31 20:09: 34 CEST 2006 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs Decrementer Frequency = 252000000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0) Console: colour dummy device 80x25 Calibrating delay loop... 66.96 BogoMIPS Memory: 30776k available (1184k kernel code, 348k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. Squashfs 2.2-r2 (released 2005/09/08) © 2002-2005 Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:13:e4:af loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank Intel/Sharp Extended Query Table at 0x0035 cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00540000 : "root (squashfs)" 0x00540000-0x007e0000 : "var (jffs2)" 0x007e0000-0x00800000 : "FLFS (U-Boot)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.1.3 (2006.08.31-18:14+0000) multi-call mount: Mounting /dev/mtdblock/2 on /var failed: No such file or directory event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ Detected STB: Vendor: Nokia Model: D-BOX2 [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 $Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $ $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $ avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $ avia_gt_core: autodetecting chip type... GTX avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $ avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $ avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $ avia_gt_core: masking unhandled irq reg 1 bit 11 avia_gt_core: masking unhandled irq reg 1 bit 13 avia_gt_ucode: loaded ucode v001A avia_gt_ucode: ucode section filters disabled. avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning... avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $ avia_gt_gv: set_input_size (width=720, height=576) avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $ avia_gt_pcm_set_rate(44100) avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $ avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $ avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $ avia_gt_core: Loaded AViA eNX/GTX driver avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $ avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) Console: switching to colour frame buffer device 82x32 avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $ avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $ avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $ avia_gt_pcm_set_rate(44100) avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $ DVB: registering frontend 0:0 (VES1893)... avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $ avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $ avia_gt_proc: $Id: avia_gt_proc.c, v 0.1.3 2005/12/11 22:30:00 Skars & Merandos Exp $ avia_gt_proc: Description: GTX/ENX proc_dev Driver with proc_fs extension options: (demux reinit) enx_reset=1 (framer chan.) fc_reset=1 (clr avia reg) avia=0 (enx td trace) trace=1 (lock, unlock) spinlock=0 Schreiben ueber /proc/bus/gtx (delay) delay=500 Starting the automounter Please press Enter to activate this console. Thu Jan 1 01:00:00 CET 1970 $Id: sectionsd.cpp,v 1.227 2006/06/08 20:19:32 houdini Exp $ [sectionsd] Caching max 6000 events [sectionsd] Caching 14 days [sectionsd] Events are old 60min after their end time /var/plugins/operations logcs_init /var/plugins/operations camd_init $Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 Kroki & Worschter Exp $ [zapit] MAX_SOCKETS=3 [zapit] PMT update enabled /var/plugins/operations cardserver_start /var/plugins/operations camd_start starte scam [getservices] /var/tuxbox/config/zapit/myservices.xml found. [getservices] dup transponder id 3 onid 85 [getservices] dup transponder id 11 onid 85 [getservices] dup transponder id 2 onid 85 [getservices] dup transponder id 4 onid 85 [getservices] dup transponder id 1 onid 85 /tmp/currentservices.xml: No such file or directory $Id: controld.cpp,v 1.124 2006/06/27 10:21:59 barf Exp $ [controld] Boxtype detected: (1, Nokia D-BOX2) [controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1 [yhttpd] Webserver nhttpd/3.1.2 (yhttpd_core/1.2.0) [LCDFONT] initializing core... [LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular) [LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold) [LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular) [LCDFONT] Intializing font cache... [yhttpd] Webserver starting... /var/plugins/operations epg_reinit neutrino: /lib/libpng12.so.0: no version information available (required by neut rino) [neutrino] frameBuffer Instance created 812k video mem avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) [neutrino] Software update enabled [neutrino] enable flash [lcdd] time-skin not found -> using default... [lcdd] weekday-skin not found -> using default... [lcdd] date-skin not found -> using default... [lcdd] month-skin not found -> using default... [LCDFONT] initializing core... [LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular) [LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold) [LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold) [LCDFONT] Intializing font cache... [LCDFONT] FTC_Face_Requester (Fix15/Bold) [LCDFONT] FTC_Face_Requester (Fix14/Bold) /dev/input/event1: No such file or directory [neutrino] menue setup [neutrino] received 43 sats [neutrino] registering as event client [neutrino] initialized everything avia_gt_core: masking unhandled irq reg 0 bit 6 avia_gt_core: masking unhandled irq reg 0 bit 7 PES, queue 0 normal. DMXDEV COMPAT: DMX_SET_FILTER pid 1 [CBasicClient] connect failed: /tmp/camd.sock01 avia_gt_core: masking unhandled irq reg 1 bit 15 DMXDEV COMPAT: DMX_STOP DMXDEV COMPAT: DMX_SET_FILTER pid 1 /tmp/camd.sock01: No such file or directory [CBasicClient] connect failed: /tmp/camd.sock02 /tmp/camd.sock02: No such file or directory [controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 4:3) [sectionsd] getUTC: read: Connection timed out Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
cd-killer Geschrieben 23. Juni 2007 Melden Share Geschrieben 23. Juni 2007 Hab das gleiche Problem mit 2Sagemboxen und dem neuesten keyweltimage(Kabel).Immer beim hochfahren, egal welcher Sender,kommt Kanal nicht verfügbar.Nach dem umschalten läuft alles ohne Probleme.Weiss jemand woran das liegen könnte? Aloha Habe 2xI Nokia Avia600 Sat mit KEYWELT_V1beta6_Sep_2x_noHDD_SQUASHFS_2006_Nokia-2xIntel-Avia600L_SAT und auch immer beim hochfahren, egal welcher Sender, kommt "Kanal nicht verfügbar". Nach dem umschalten läuft alles ohne Probleme. Ansonsten geht soweit alles stabil stay tuned Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 23. Juni 2007 Autor Melden Share Geschrieben 23. Juni 2007 Ich habe zu diesem "Kanal nicht verfügbar" beim Einschalten der Box keine plausible Erklärung. Am Image selber kann es normal nicht liegen, sonst müßte das generell immer auftreten. Ich hatte gestern eine Nokia SAT (Avia600) hier, hab die in den Debug gebracht und das KW-September-V1-Beta6 draufgespielt, so wie es im DL verfügbar ist. Die Box läuft auf Anhieb tadellos, da gibt's kein "Kanal nicht verfügbar"... Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Frankie7878 Geschrieben 24. Juni 2007 Melden Share Geschrieben 24. Juni 2007 Hallo ! Naja ich hab gestern zufällig eine Nokia Avia 500 Box Debugt und mit den Image bespielt, selber Fehler . ALso müsste es an den 500 Chip irgendwie liegen . Treiber usw habe ich auch schon bei der ersten Box geändert, bringt auch nichts . Vieleicht wenn es hilft, meine Sat Anlage läuft über einen Multischalter ( 4 Eingänge, 8 Ausgange ) obwohl andere Reciver alle Problemlos damit Problemlos laufen, naja hab diese bei anderen Images bis jetzt auch noch nicht erlebt . Zudem frirte das Image teilweise sehr schnell ein,aber seidem ich nur noch eine lehre Cam3 drin habe, scheint dieses Behoben zu sein . Frankie Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
deadlyblade Geschrieben 24. Juni 2007 Melden Share Geschrieben 24. Juni 2007 Wegen dem Problem, ersetzt mal die calbes.xml mit der ausm DownloadBereich, hatte damals bei mir geholfen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Donalt Geschrieben 24. Juni 2007 Melden Share Geschrieben 24. Juni 2007 "Kanal nicht verfügbar" Probiert mal: Hauptmenü>Keywelt settings>Zapit Einstellungen>Zapit tune-mode auf "EIN" schalten Ich hatte im Juni Version bei "AUS" schon Problemme gruss Donalt Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Luis942 Geschrieben 25. Juni 2007 Melden Share Geschrieben 25. Juni 2007 Ich habe zu diesem "Kanal nicht verfügbar" beim Einschalten der Box keine plausible Erklärung. Am Image selber kann es normal nicht liegen, sonst müßte das generell immer auftreten. Ich hatte gestern eine Nokia SAT (Avia600) hier, hab die in den Debug gebracht und das KW-September-V1-Beta6 draufgespielt, so wie es im DL verfügbar ist. Die Box läuft auf Anhieb tadellos, da gibt's kein "Kanal nicht verfügbar"... ich hab das problem auch mit dem kanal nicht verfügbar. ich habe ne nokia 2xi mit nem 600L chip. ich denke aber das es an den camd liegt, wi ich die enthaltene camd3 hatte war alles ok, als ich die mgcam oder die scam drauf gemacht habe hatte ich den fehler mit kanal nicht verfügbar nach dem start. wenn ich dann umstelle funktioniert alles perfekt. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 25. Juni 2007 Autor Melden Share Geschrieben 25. Juni 2007 @Luis942 Ein Em* ist für das Problem "Kanal nicht verfügbar" unter Garantie nicht verantwortlich... Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Luis942 Geschrieben 25. Juni 2007 Melden Share Geschrieben 25. Juni 2007 @Luis942 Ein Em* ist für das Problem "Kanal nicht verfügbar" unter Garantie nicht verantwortlich... ok, dachte ja nur, da ich das problem vorher nicht hatte.... Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
dietz Geschrieben 25. Juni 2007 Melden Share Geschrieben 25. Juni 2007 @merkwuerden Hi! So wie es scheint ist das "kanal nicht verfügbar" nach dem booten doch ein imageproblem. Hab auf meine sagem kabel 1x1mit HDD das image no hdd geflasht und da tritt das Problem auf.Beim hdd image alles bestens. Gruss Dietz Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Empfohlene Beiträge
Archiviert
Dieses Thema ist jetzt archiviert und für weitere Antworten gesperrt.