wiedzmin Geschrieben 4. April 2007 Melden Share Geschrieben 4. April 2007 moin moin hab da ein prob mit meine nokia box. habe die box an strom angeschlossen und die fährt nicht mal ganz hoch sondern fängt nach ca. 5 sec. die sachen von anfang an. das wiederholt sich die ganze zeit. sobalt ich die aber resete fährt sie ganz normal hoch und wenn ich glück habe bleibt es so und wenn nicht fährt sie nach paar min. wieder runter und das geht dann von anfang an. ab und zu bleib sie auch an. kennt jemand das problem? ist die box durch oder hängt es an image? bitte um info danke im voraus gruß wiedzmin Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Tunina Geschrieben 4. April 2007 Melden Share Geschrieben 4. April 2007 ist die box durch oder hängt es an image?Image bereits neu geflasht? War zuvor alles ok oder ist es eine neu erworbene Boxß Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
wiedzmin Geschrieben 4. April 2007 Autor Melden Share Geschrieben 4. April 2007 hab jetzt ne neue image drauf und das selbe problem. habe das schon seid paar tagen Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Admin SnowHead Geschrieben 4. April 2007 Admin Melden Share Geschrieben 4. April 2007 @wiedzmin Ein Bootlog könnte uns helfen Dir zu helfen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
wiedzmin Geschrieben 4. April 2007 Autor Melden Share Geschrieben 4. April 2007 hatte auch probs mit flashen. hier der log von hallenberg. vielleicht könnt ihr was draus erkännen. ûdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPSdebug: BMon V1.2 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID http://Hallenberg.com debug: HWrev 09 FPrev 0.81 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled debug: autoboot aborted from terminal dbox2:root> dbox2:root> boot net net net net net net net net net net debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Got BOOTP reply from Server IP 192.168.0.60, My IP 192.168.0.202 debug: Sending TFTP-request for file D/dboxifa_tmp/tftpboot/u-boot will verify ELF image, start= 0x800000, size= 140336 verify sig: 263 boot net: boot file has no valid signature Branching to 0x40000 U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14) CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Nokia, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-lcd'. Load address: 0x100000 Loading: *## done Bytes transferred = 7680 (1e00 hex) BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-fb'. Load address: 0x100000 Loading: *#################################### done Bytes transferred = 179877 (2bea5 hex) Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit Size: 8192 kB in 71 Sectors Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'kernel-yadd'. Load address: 0x100000 Loading: *################################################################# ################################################################# #################### done Bytes transferred = 763552 (ba6a0 hex) ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 763488 Bytes = 745.6 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK dbox2 - ImageFlashingAssistent - Hallenberg.com - Wilkommen auf ihrer dbox2 Starte Backup.... Schreibe Backup: 5504k von 8064k (68%)debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: WATCHDOG RESET debug: BMon V1.2 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID http://Hallenberg.com debug: HWrev 09 FPrev 0.81 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled debug: autoboot aborted from terminal dbox2:root> dbox2:root> boot net net net net net net net net net net debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Got BOOTP reply from Server IP 192.168.0.60, My IP 192.168.0.202 debug: Sending TFTP-request for file D/dboxifa_tmp/tftpboot/u-boot will verify ELF image, start= 0x800000, size= 140336 verify sig: 263 boot net: boot file has no valid signature Branching to 0x40000 U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14) CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Nokia, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-lcd'. Load address: 0x100000 Loading: *## done Bytes transferred = 7680 (1e00 hex) BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-fb'. Load address: 0x100000 Loading: *#################################### done Bytes transferred = 179877 (2bea5 hex) Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit Size: 8192 kB in 71 Sectors Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'kernel-yadd'. Load address: 0x100000 Loading: *################################################################# ################################################################# #################### done Bytes transferred = 763552 (ba6a0 hex) ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 763488 Bytes = 745.6 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: WATCHDOG RESET debug: BMon V1.2 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID http://Hallenberg.com debug: HWrev 09 FPrev 0.81 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled debug: autoboot aborted from terminal dbox2:root> dbox2:root> boot net net net net net net net net net net debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Got BOOTP reply from Server IP 192.168.0.60, My IP 192.168.0.202 debug: Sending TFTP-request for file D/dboxifa_tmp/tftpboot/u-boot will verify ELF image, start= 0x800000, size= 140336 verify sig: 263 boot net: boot file has no valid signature Branching to 0x40000 U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14) CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Nokia, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-lcd'. Load address: 0x100000 Loading: *## done Bytes transferred = 7680 (1e00 hex) BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-fb'. Load address: 0x100000 Loading: *#################################### done Bytes transferred = 179877 (2bea5 hex) Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit Size: 8192 kB in 71 Sectors Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'kernel-yadd'. Load address: 0x100000 Loading: *################################################################# ################################################################# #################### done Bytes transferred = 763552 (ba6a0 hex) ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 763488 Bytes = 745.6 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: WATCHDOG RESET debug: BMon V1.2 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID http://Hallenberg.com debug: HWrev 09 FPrev 0.81 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled debug: autoboot aborted from terminal dbox2:root> dbox2:root> boot net net net net net net net net net net debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Got BOOTP reply from Server IP 192.168.0.60, My IP 192.168.0.202 debug: Sending TFTP-request for file D/dboxifa_tmp/tftpboot/u-boot will verify ELF image, start= 0x800000, size= 140336 verify sig: 263 boot net: boot file has no valid signature Branching to 0x40000 U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14) CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Nokia, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-lcd'. Load address: 0x100000 Loading: *## done Bytes transferred = 7680 (1e00 hex) BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-fb'. Load address: 0x100000 Loading: *#################################### done Bytes transferred = 179877 (2bea5 hex) Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit Size: 8192 kB in 71 Sectors Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'kernel-yadd'. Load address: 0x100000 Loading: *################################################################# ################################################################# #################### done Bytes transferred = 763552 (ba6a0 hex) ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 763488 Bytes = 745.6 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK dbox2 - ImageFlashingAssistent - Hallenberg.com - Wilkommen auf ihrer dbox2 Starte Backup.... Schreibe Backup: 8064k von 8064k (100%) Backup abgeschlossen! Der Flashprozess wird nun gestartet... Lösche Sektoren: 63 von 63 (100%) Schreibe Daten: 8064k von 8064k (100%) Verifziere Daten: 8064k von 8064k (100%) Flashen beendet! Sie koennen die dbox jetzt ausschalten. Please press Enter to activate this console. debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: WATCHDOG RESET debug: BMon V1.2 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID http://Hallenberg.com debug: HWrev 09 FPrev 0.81 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled debug: autoboot aborted from terminal dbox2:root> dbox2:root> boot net net net net net net net net net net debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Got BOOTP reply from Server IP 192.168.0.60, My IP 192.168.0.202 debug: Sending TFTP-request for file D/dboxifa_tmp/tftpboot/u-boot will verify ELF image, start= 0x800000, size= 140336 verify sig: 263 boot net: boot file has no valid signature Branching to 0x40000 U-Boot 1.1.2 (Tuxbox) (Jun 12 2005 - 13:44:14) CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Nokia, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-lcd'. Load address: 0x100000 Loading: *## done Bytes transferred = 7680 (1e00 hex) BOOTP broadcast 1 Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'D/dboxifa_tmp/tftpboot/u-boot'. Load address: 0x100000 Loading: *Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename '/tftpboot/logo-fb'. Load address: 0x100000 Loading: *#################################### done Bytes transferred = 179877 (2bea5 hex) Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 Bank # 1: INTEL 28F320C3B (32M, bottom boot sect), 32 bit Size: 8192 kB in 71 Sectors Using SCC ETHERNET device TFTP from server 192.168.0.60; our IP address is 192.168.0.202 Filename 'kernel-yadd'. Load address: 0x100000 Loading: *################################################################# ################################################################# #################### done Bytes transferred = 763552 (ba6a0 hex) ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 763488 Bytes = 745.6 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK dbox2 - ImageFlashingAssistent - Hallenberg.com - Wilkommen auf ihrer dbox2 Starte Backup.... Schreibe Backup: 8064k von 8064k (100%) Backup abgeschlossen! Der Flashprozess wird nun gestartet... Lösche Sektoren: 63 von 63 (100%) Schreibe Daten: 8064k von 8064k (100%) Verifziere Daten: 8064k von 8064k (100%) Flashen beendet! Sie koennen die dbox jetzt ausschalten. Please press Enter to activate this console. ------ Zusatzinformationen ------ Gewählter Netzwerkadapter: D-Link DE-530+ PCI-Ethernetadapter - Paketplaner-Miniport (1) IP-Adresse des Netzwerkadapters: 192.168.0.60 IP-Adresse die die dbox bekommt: 192.168.0.202 Comport: Kommunikationsanschluss (COM1) Betriebssystem: Microsoft Windows XP Professional Service Pack 2 (Build 2600) CPU 1: AMD Athlon XP 2700+ @ 2160 MHz Dateiname des Images: KEYWELT_V1_SEPTEMBER_2x_SQUASHFS_2006.img Imagetyp: Zwei Flashs DBOX-IFA Version: 2.0 ------ Powered by http://www.dboxservice-hallenberg.de ------ nach bestimmte zeit hat er das image gefressen. ist nur einmal flashen gewesen, so habe ich es auch noch nicht gesehen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Tunina Geschrieben 4. April 2007 Melden Share Geschrieben 4. April 2007 nach bestimmte zeit hat er das image gefressen.ist nur einmal flashen gewesen, so habe ich es auch noch nicht gesehen. Bilde mir ein Texte lesen zu können. Ist/war für mich immer wichtig. Sorry, bei dieser Deiner Antwort bauche ich aber ne Glaskugel. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
wiedzmin Geschrieben 4. April 2007 Autor Melden Share Geschrieben 4. April 2007 nach bestimmte zeit hat er das image gefressen.ist nur einmal flashen gewesen, so habe ich es auch noch nicht gesehen. Bilde mir ein Texte lesen zu können. Ist/war für mich immer wichtig. Sorry, bei dieser Deiner Antwort bauche ich aber ne Glaskugel. ich weiss nicht was da nicht zum verstehen ist diese log ist nur aus einem flashen und so wie es im log aussieht hat der flashassisten öfter mal versucht zu flashen und habe auch ne vermutung das die box auch dabei immer wieder neu gestartet hat. ist das deutlicher für dich??? Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Tunina Geschrieben 4. April 2007 Melden Share Geschrieben 4. April 2007 nach bestimmte zeit hat er das image gefressen.ist nur einmal flashen gewesen, so habe ich es auch noch nicht gesehen. Meine Irritation bezog sich nicht auf das Log vom Assi, sondern auf den Kommentar. Möglicherweise habe ich den Kommentar schlicht nicht kapiert. Aber lassen wir das. Versuchs einfach mal nur mit dem Manager oder per FTP. Erst kürzlich hatte ich per FTP/Expertenfunktion Erfolg - nach dem es zuvor weder mit Manager und Assi funktioniert hatte. Ich weiß, dass das eigentlich nicht sein kann.... Sowas bringt mich aber immer wieder zu der Erkenntnis, - ich weiß, dass ich nichts weiß. (Sokrates - 469 bis 396 v. Chr.) Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Empfohlene Beiträge
Archiviert
Dieses Thema ist jetzt archiviert und für weitere Antworten gesperrt.