Jump to content
skyline666

Kein Bild über HDMI aber Scart ist ok

Empfohlene Beiträge

Hallo User, 

 

 ich wollte gestern an meinem Fernseher einen alten AppleTV anschließen und habe dabei das HDMI Kabel meiner Zee2 genutzt.

Nach dem Testen habe ich dann die Coolie wieder angestöpselt und dann hatte ich die Situation, dass kein Bild mehr erschien.

Nur Ton erscheint aus dem Lautsprecher. 
Dann das gleiche noch mal mit HDMI auf einen PC Monitor probiert. Ergebnis gleich bis auf das dort der Coolstream 

Bildschirm (vermute ROM Bild) erscheint. 
Schon beim starten des Images kommt kein Bild. 
Bei Scart kommt zwar auch zwischendurch ein Bild mit wirren grünen Streifen aber dann das normale Fernsehbild. 
 

Habe ich etwas zerschossen an der Hardware beim stecken?

 

Könnte man noch was testen?

 

Mfg Skyline666

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen
Am 29.12.2019 um 08:13 schrieb skyline666:

Habe ich etwas zerschossen an der Hardware beim stecken?

 

Könnte man noch was testen?

 

 

Vermutlich HDMI Chip abgeschossen, mach mal ein Bootlog mit Putty.

Der HDMI Ausgang der Cooli ist empfindlich was statische Überspannung betrifft.

Netzteil würde ich auch mal überprüfen.

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen

Das ist mir mit meiner Neo V1 auch so gegangenen. Ich hab sie dann als defekt verkauft, der Käufer hat das mir dann bestätigt das der HDMI bei ihm auch nicht geht. 

Die Nevis Boxen sind da echt empfindlich. 

Auslöser hier war eine Umverkabelung der Sät, Netz, und HDMI Kabel um die Leitungsführung zu optimieren und Aufzuhübschen, ich hätte es einfach scheiße aussehen lassen sollen. 

bearbeitet von topie88

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen
Am 29.12.2019 um 09:08 schrieb Gandal:

 

Vermutlich HDMI Chip abgeschossen, mach mal ein Bootlog mit Putty.

Der HDMI Ausgang der Cooli ist empfindlich was statische Überspannung betrifft.

Netzteil würde ich auch mal überprüfen.

 

Hallo Gandal,

 

hier das bootlog!

 

Schau bitte mal mit Deiner fachlichen Kompetenz mal rüber. Dir schon im Voraus vielen Dank!

 

 


Starting Microloader ASM built on Mar 28 2016 18:03:24...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Starting Microloader C...
Chip: KRONOS
Found Internal MYSTI110 PHY on GMAC0
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
BOX MAC OK!
BOX: Type: ZEE Rev: 75500100
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 600 ms since POR

--------------------------------------------------------------------------------
| U-Boot 2009.08-00068-g69a4049 (Dec 10 2015 - 14:51:59)               CST HDx |
|------------------------------------------------------------------------------|
| Chipset information                                                          |
| Vendor: Entropic  Type: KRONOS           Revision: B0        Fuses: 00010001 |
|------------------------------------------------------------------------------|
| Clock information                                                            |
| *** not available yet ***                                                    |
|------------------------------------------------------------------------------|
| Frontpanel information                                                       |
| Vendor: CST       Version: 3.3           Display: OLED (128 x 64 px)         |
|------------------------------------------------------------------------------|
| Memory configuration                                                         |
| Start    | End      | Type    | Description                                  |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 1FFFFFFF | RAM     | System main memory bank #0 (512M)            |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K x  64)      |
  *** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit               |
|------------------------------------------------------------------------------|
| Network configuration                                                        |
| MAC: LIP 6300                    address: 00-C5-5C-25-BA-B7                  |
--------------------------------------------------------------------------------

Hit any key to stop autoboot:  0

SFC read: offset 0x100000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Coolstream Kernel (compressed)
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2981377 Bytes =  2.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.10.93 (image@server) (gcc version 6.3.1 20170109 (crosstool-NG 1) ) #1 SMP Sun Apr 15 15:27:43 CEST 2018
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Entropic Kronos STB Platform with FDT, model: CoolStream HD2 Kronos STB
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Early platform io descriptors mapping...
[    0.000000] PERCPU: Embedded 7 pages/cpu @80da8000 s5952 r8192 d14528 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 247144k/247144k available, 277144k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.000000]       .text : 0x80008000 - 0x806584f8   (6466 kB)
[    0.000000]       .init : 0x80659000 - 0x80687740   ( 186 kB)
[    0.000000]       .data : 0x80688000 - 0x806c8e60   ( 260 kB)
[    0.000000]        .bss : 0x806c8e60 - 0x806e3224   ( 105 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU debugfs-based tracing is enabled.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:350
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] Cortex A9 frequency at 600 MHz
[    0.000000] Initializing Cortex A9 Global Timer at Vir:0xFEA00200, using, at Freq:300 MHz
[    0.000000] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 14316ms
[    0.000000] smp_twd: clock not found -2
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.249862] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    0.292758] pid_max: default: 32768 minimum: 301
[    0.297561] Mount-cache hash table entries: 512
[    0.303983] CPU: Testing write buffer coherency: ok
[    0.309079] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.314707] Setting up static identity map for 0x803c47a0 - 0x803c47f8
[    0.321240] L310 cache controller enabled
[    0.325158] l2x0: 8 ways, CACHE_ID 0x410004c7, AUX_CTRL 0x32421001, Cache size: 131072 B
[    0.333783] Brought up 1 CPUs
[    0.336657] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[    0.342981] CPU: All CPU(s) started in SVC mode.
[    0.348245] devtmpfs: initialized
[    0.356639] NET: Registered protocol family 16
[    0.361753] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.475139] GMAC0: active interface is 1
[    0.479129] ChipID=0x1000 ChipRevID=0x100
[    0.483229] nx_dmac: Registered with 8 channels
[    0.510019] bio: create slab <bio-0> at 0
[    0.515383] GPIO: base febab000 (phys e06ab000)
[    0.519974] GPIO: base feb69000 (phys e0669000)
[    0.526358] SCSI subsystem initialized
[    0.531482] usbcore: registered new interface driver usbfs
[    0.537065] usbcore: registered new interface driver hub
[    0.542721] usbcore: registered new device driver usb
[    0.548157] pps_core: LinuxPPS API ver. 1 registered
[    0.553080] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.562363] PTP clock support registered
[    0.567932] cfg80211: Calling CRDA to update world regulatory domain
[    0.575726] Switching to clocksource arm_global_timer
[    0.599560] NET: Registered protocol family 2
[    0.604685] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.611749] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.618153] TCP: Hash tables configured (established 4096 bind 4096)
[    0.624476] TCP: reno registered
[    0.627617] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.633439] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.639880] NET: Registered protocol family 1
[    0.644492] RPC: Registered named UNIX socket transport module.
[    0.650368] RPC: Registered udp transport module.
[    0.654968] RPC: Registered tcp transport module.
[    0.659634] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.666226] PM: STB Platform power mgmt initialization.
[    0.797202] NFS: Registering the id_resolver key type
[    0.802279] Key type id_resolver registered
[    0.806359] Key type id_legacy registered
[    0.810381] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.816753] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.824728] msgmni has been set to 482
[    0.829765] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.837125] io scheduler noop registered
[    0.840977] io scheduler deadline registered
[    0.845839] io scheduler cfq registered (default)
[    0.851209] e06b2000.serial: ttyS0 at MMIO 0xe06b2000 (irq = 47) is a uart-ip3106
[    0.865585] loop: module loaded
[    0.869716] ahci-stb e0638000.sata: unable to find phy
[    0.874818] SATA: Enable mpll_ss_en (rd_val=0x571185, wr_val=0x5711a5)
[    0.881253] SATA: Enable rx_term_en0 (rd_val=0x277, wr_val=0x277)
[    0.887317] ahci-stb e0638000.sata: SSS flag set, parallel bus scan disabled
[    0.894325] ahci-stb e0638000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    0.903113] ahci-stb e0638000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    0.912581] ata4294967295: SATA PHY offline
[    0.917602] scsi0 : ahci_platform
[    0.921555] ata1: SATA max UDMA/133 mmio [mem 0xe0638000-0xe0638fff] port 0x100 irq 39
[    0.931025] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
[    0.943425] Bad block table found at page 262080, version 0x01
[    0.949940] Bad block table found at page 262016, version 0x01
[    0.956197] nand_read_bbt: bad block at 0x00001cf60000
[    0.961260] nand_read_bbt: bad block at 0x00001cfa0000
[    0.966387] 3 cmdlinepart partitions found on MTD device e0631000.flash_nand
[    0.973341] Creating 3 MTD partitions on "e0631000.flash_nand":
[    0.979207] 0x000000000000-0x000010000000 : "root0"
[    0.985757] 0x000010000000-0x000012000000 : "var"
[    0.991851] 0x000012000000-0x000020000000 : "root1"
[    1.000185] JEDEC ID = 0x1c3016 , Extended Device ID = 0x1c30
[    1.005931] nx_sfc e0632000.flash_sfc: en25q32 (4096 Kbytes)
[    1.011572] 5 cmdlinepart partitions found on MTD device e0632000.flash_sfc
[    1.018446] Creating 5 MTD partitions on "e0632000.flash_sfc":
[    1.024260] 0x000000000000-0x000000040000 : "uldr"
[    1.030646] 0x000000040000-0x0000000c0000 : "u-boot"
[    1.036952] 0x0000000c0000-0x0000000e0000 : "env"
[    1.043086] 0x0000000e0000-0x000000100000 : "spare"
[    1.049323] 0x000000100000-0x000000400000 : "kernel"
[    1.056379] tun: Universal TUN/TAP device driver, 1.6
[    1.061405] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.068051]  DWMAC1000
[    1.070350] stmmac - user ID: 0x36, Synopsys ID: 0x36
[    1.075329]  Ring mode enabled
[    1.078354]  DMA HW capability register supported
[    1.082866]  Enhanced/Alternate descriptors
[    1.087166]  Enabled extended descriptors
[    1.091151]  RX Checksum Offload Engine supported (type 2)
[    1.096584]  TX Checksum insertion supported
[    1.100824]  Wake-Up On Lan supported
[    1.104489]  Enable RX Mitigation via HW Watchdog Timer
[    1.124471] libphy: stmmac: probed
[    1.127791] eth0: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) active
[    1.134167] eth0: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
[    1.139806] eth0: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
[    1.145526] eth0: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
[    1.151224] eth0: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
[    1.156913] eth0: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
[    1.162622] eth0: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
[    1.168317] eth0: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
[    1.174026] eth0: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
[    1.179722] eth0: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
[    1.185430] eth0: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
[    1.191219] eth0: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
[    1.197002] eth0: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
[    1.202797] eth0: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
[    1.208579] eth0: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
[    1.214374] eth0: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
[    1.220163] eth0: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
[    1.225945] eth0: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
[    1.231740] eth0: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
[    1.237524] eth0: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
[    1.243317] eth0: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
[    1.249100] eth0: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
[    1.254896] eth0: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
[    1.260683] eth0: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
[    1.266467] eth0: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
[    1.272262] eth0: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
[    1.278045] eth0: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
[    1.283840] eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
[    1.289622] eth0: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
[    1.295416] eth0: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
[    1.301205] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
[    1.306988] eth0: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
[    1.313044] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.319464] ehci-platform: EHCI generic platform driver
[    1.324938] ehci-platform e066c000.usb: EHCI Host Controller
[    1.330565] ehci-platform e066c000.usb: new USB bus registered, assigned bus number 1
[    1.338383] ehci-platform e066c000.usb: irq 93, io mem 0xe066c000
[    1.360091] ehci-platform e066c000.usb: USB 2.0 started, EHCI 1.00
[    1.366240] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.372950] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.380103] usb usb1: Product: EHCI Host Controller
[    1.384923] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.390383] usb usb1: SerialNumber: e066c000.usb
[    1.395860] hub 1-0:1.0: USB hub found
[    1.399534] hub 1-0:1.0: 1 port detected
[    1.403709] ehci-platform e066d000.usb: EHCI Host Controller
[    1.409280] ehci-platform e066d000.usb: new USB bus registered, assigned bus number 2
[    1.417194] ehci-platform e066d000.usb: irq 94, io mem 0xe066d000
[    1.423247] ata1: SATA PHY offline
[    1.426571] ata1: SATA link down (SStatus 0 SControl 300)
[    1.440078] ehci-platform e066d000.usb: USB 2.0 started, EHCI 1.00
[    1.446233] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.452945] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.460101] usb usb2: Product: EHCI Host Controller
[    1.464921] usb usb2: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.470375] usb usb2: SerialNumber: e066d000.usb
[    1.475761] hub 2-0:1.0: USB hub found
[    1.479435] hub 2-0:1.0: 1 port detected
[    1.484046] usbcore: registered new interface driver usb-storage
[    1.490439] usbcore: registered new interface driver usbserial
[    1.497743] usbcore: registered new interface driver usbhid
[    1.503283] usbhid: USB HID core driver
[    1.507270] TCP: cubic registered
[    1.510517] NET: Registered protocol family 17
[    1.515327] Key type dns_resolver registered
[    1.519602] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 3
[    1.527137] ThumbEE CPU extension supported.
[    1.532426] ### dt-test ### No testcase data in device tree; not running tests
[    1.730080] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.881640] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    1.888259] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.895349] usb 1-1: Product: USB2.0 Hub
[    1.900632] hub 1-1:1.0: USB hub found
[    1.904641] hub 1-1:1.0: 4 ports detected
[    2.600058] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    2.752190] usb 2-1: New USB device found, idVendor=174c, idProduct=5136
[    2.758805] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    2.765890] usb 2-1: Product: AS2105
[    2.769415] usb 2-1: Manufacturer: ASMedia
[    2.773483] usb 2-1: SerialNumber: 00000000000000000000
[    2.779840] usb-storage 2-1:1.0: USB Mass Storage device detected
[    2.786109] scsi1 : usb-storage 2-1:1.0
[    3.791054] scsi 1:0:0:0: Direct-Access     ASMT     2105             0    PQ: 0 ANSI: 6
[    3.800888] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    4.624990] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    4.633348] sd 1:0:0:0: [sda] Write Protect is off
[    4.638842] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.673503]  sda: sda1
[    4.679350] sd 1:0:0:0: [sda] Attached SCSI disk
[    6.959898] VFS: Mounted root (jffs2 filesystem) on device 31:0.
[    6.967185] devtmpfs: mounted
[    6.970351] Freeing unused kernel memory: 184K (80659000 - 80687000)
init started: BusyBox v1.30.1 (2019-06-22 15:09:50 CEST)
[    7.853314] NET: Registered protocol family 10
try to mount /dev/mtdblock1 to /var
[    8.286337] jffs2: Empty flash at 0x01088ad8 ends at 0x01089000
starting /etc/init.d/S02loadmodules ...
Sat Jan  1 00:00:00 CET 2000
Creating device node for cs_display
Running insmod now .......
Driver modules loaded, please start the app now...
Creating device node for KAL
Creating device node for notifyq
Creating device node for platform
Creating device node for content
Creating device node for standby
Creating device node for video
Creating device node for audio
Creating device node for pvr
Creating device node for ci
Creating device node for cs_control
Creating device node for cs_ir
Creating device node for fb
starting /etc/init.d/S04mdev ...
[logoview] done with Timeout...
error connect socket /tmp/neutrino.sock: No such file or directory
starting /etc/init.d/S05mount ...
starting /etc/init.d/S50hostname ...
starting /etc/init.d/S51networking ...
Configuring network interfaces... Starting wlan0
Failed to connect to wpa_supplicant - wpa_ctrl_open: Success
Could not read interface wlan0 flags: No such device
Failed to initialize driver interface
done.
starting /etc/init.d/S52syslogd ...
Jan  1 00:00:14 CST-25BAB7 syslog.info syslogd started: BusyBox v1.30.1
starting /etc/init.d/S60autofs ...
 1 Jan 00:00:14 ntpdate[1137]: ntpdate 4.2.8p6@1.3265-o (1)
starting
starting /etc/init.d/S80dvdreadfs ...
starting /etc/init.d/S90inetd ...
starting /etc/init.d/S96nfsd ...
starting /var/etc/init.d/S9T_tuxcald ...
starting /var/etc/init.d/S9T_tuxmaild ...
Jan  1 00:00:15 CST-25BAB7 daemon.info : starting pid 1173, tty '': '/etc/init.d/start_neutrino'

Please press Enter to activate this console. /var/plugins/operations camd_init
/var/plugins/operations cardserver_start
starte doscam
Sat Jan  1 00:00:16 CET 2000
/var/plugins/operations camd_start
/var/plugins/operations rezap
30 Dec 12:56:21 ntpdate[1137]: step time server 130.133.1.10 offset 631025765.066037 sec
/var/plugins/operations: line 262: 6: not found
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend3: No such file or directory
MON: The POD Monitor task has started. Version = 01, Release = 00, Subrelease = 01, PID: 1213
MON: Initializing
slot->inbound_queue : 76076070
slot->outbound_queue: 76075f18
xport_command_queue: 76075d00
MON: Start resource providers...
XPORT: POD Transport task started. PID: 1213
RM: Resource Manager thread started. PID: 1213
XPORT: transport connection #1 set to Idle
LINK: POD link task started with arg=0x00000000, PID: 1213
MON: Starting 9 resource(s).
MON starting 9 resources finished
MON after BR_POD_mon_start_rps
POD timer thread PID: 1213
comming in  add resource provider, rid=10041
RM before wait for db ready, pid: 1213
APPMMI thread starts, PID: 1213
UPGRADE thread is started, PID: 1213
comming in  add resource provider, rid=8e1001
HOSTCTRL thread is started, PID: 1213
comming in  add resource provider, rid=200041
SYSTIME resource start, PID: 1213
comming in  add resource provider, rid=240041
SYSTIME RP: System Time main loop processing started.
CA resource provider started with arg=0x00000000, PID: 1213
APPINFO thread starts, PID: 1213
comming in  add resource provider, rid=20043
APPINFO RP: resource provider is added, resource ID :0x20043
APPINFO RP: APPINFO resource provider main loop processing started.
RM after wait for db ready, pid: 1213
HOSTLANG_CNTY thread is started, PID: 1213
comming in  add resource provider, rid=8d1001
MMI thread is started, PID: 1213
comming in  add resource provider, rid=400041
CP resource start, PID: 1213
CP thread get delay time 0(s)
CP: Start of initialization...
HOSTCTRL RP: resource provider is added
ciappReportModuleStatus: status 9, gCardStatus: 0
PHYS-CI+: cs_ci_init_controller called
comming in  add resource provider, rid=410041
UPGRADE RP: resource provider is added
UPGRADE RP: UPGRADE resource provider main loop processing started.
RM: Resource Manager message processing started.
comming in  add resource provider, rid=30041
CA RP: Resource Provider main loop processing started.
HOSTLANG_CNTY RP: resource provider is added
MON after wait event
MON: Wait for all required resource providers to sign on....
APPMMI RP: resource provider is added
MMI RP: resource provider is added
HOSTCTRL RP: HOSTCTRL resource provider main loop processing started.
CP nvram: Root certificate file is for production
HOSTLANG_CNTY RP: HOSTLANG_CNTY resource provider main loop processing started.
LINK: hard reset complete.
LINK: slot #0 state = BR_POD_SLOT_NOT_INIT
MMI RP: MMI resource provider main loop processing started.
APPMMI RP: APPMMI resource provider main loop processing started.
dump mbuf....
LINK: slot #0 state = BR_POD_SLOT_CARD_NOT_PRESENT
RM: recvd LINK_STATUS tag(0x42), len=8
RM: No host-pod interface
RM: close all connections on slot 0
LINK: after bypass card
dump mbuf....
ciappReportModuleStatus: status 0, gCardStatus: 0
dump mbuf....
no CICAM brand id extension.
comming in  add resource provider, rid=8c1001
RM: recvd RM_RESOURCES_CHANGED tag(0x43), len=8
CP RP: resource provider is added
CP: Resource Provider main loop processing started.
2019-12-30 12:56:32.396 [sectionsd] start
2019-12-30 12:56:32.522 [sectionsd] starting
2019-12-30 12:56:32.689 [sectionsd] timeThread::run:: starting, pid 1213 (1672021168)
2019-12-30 12:56:32.796 [sectionsd] eitThread::run:: starting, pid 1213 (1669924016)
2019-12-30 12:56:32.811 [sectionsd] cnThread::run:: starting, pid 1213 (1667826864)
2019-12-30 12:56:32.821 [sectionsd] timeThread: get DVB time ch 0x000000000000 (isOpen 1)
2019-12-30 12:56:32.851 [sectionsd] freeSatThread::run:: starting, pid 1213 (1665729712)
[ConfigFile] Unable to open file /var/tuxbox/config/bookmarks for reading.
2019-12-30 12:56:34.040 [sectionsd] commandserviceStopped
2019-12-30 12:56:34.085 [sectionsd] cnThread: stop eit update filter (not active)
2019-12-30 12:56:34.088 [sectionsd] commandserviceStopped done
2019-12-30 12:56:34.130 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:34.302 [sectionsd] timeThread: get DVB time ch 0x00020085000a rc: -1 neutrino_sets_time 0
2019-12-30 12:56:34.309 [sectionsd] timeThread: Time set FAILED (enabled: ntp 0 dvb 1)
sh: you need to specify whom to kill
2019-12-30 12:56:35.030 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:35.070 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:35.344 [sectionsd] timeThread: get DVB time ch 0x00020085000a (isOpen 1)
2019-12-30 12:56:37.935 [sectionsd] timeThread: get DVB time ch 0x00020085000a rc: 8 neutrino_sets_time 0
2019-12-30 12:56:37.944 [sectionsd] SIsectionTIME::parse: TDT time: Mon Dec 30 12:56:36 2019
2019-12-30 12:56:37.949 [sectionsd] timeThread: timediff -1948979, current: 30.12.2019 12:56:37, dvb: Mon Dec 30 12:56:36 2019

2019-12-30 12:56:36.000 [sectionsd] cnThread::run:: time set: Mon Dec 30 12:56:36 2019

2019-12-30 12:56:36.006 [sectionsd] freeSatThread::run:: time set: Mon Dec 30 12:56:36 2019

2019-12-30 12:56:36.011 2019-12-30 12:56:36.011 [sectionsd] timeThread: Time set via DVB (TDT), going to sleep for 5 seconds.
[sectionsd] eitThread::run:: time set: Mon Dec 30 12:56:36 2019

 --- > rezapping
2019-12-30 12:56:36.732 [sectionsd] addEvent: ch 00020085000a running 0 (next) got_CN 0
2019-12-30 12:56:37.681 [sectionsd] addEvent: ch 00020085000a running 4 (curr) got_CN 2
2019-12-30 12:56:37.854 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:37.898 [sectionsd] cnThread: eit update filter, ch 0x00020085000a, current ver 0x0c  got events 3 (not active)
2019-12-30 12:56:41.050 [sectionsd] timeThread: get DVB time ch 0x00020085000a (isOpen 1)
2019-12-30 12:56:42.362 [sectionsd] timeThread: get DVB time ch 0x00020085000a rc: 29 neutrino_sets_time 0
2019-12-30 12:56:42.372 [sectionsd] SIsectionTIME::parse: TOT time: Mon Dec 30 12:56:42 2019
2019-12-30 12:56:42.376 [sectionsd] timeThread: timediff -376291, current: 30.12.2019 12:56:42, dvb: Mon Dec 30 12:56:42 2019

2019-12-30 12:56:42.389 [sectionsd] difference is < 120s, using adjtime(0, -376291). oldd(0, 0)
2019-12-30 12:56:42.399 [sectionsd] timeThread: Time set via DVB (TOT), going to sleep for 1800 seconds.
^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA^[OA
Dec 30 12:57:53 CST-25BAB7 daemon.info : starting pid 1174, tty '': '-/bin/sh'
Starting Microloader ASM built on Mar 28 2016 18:03:24...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Starting Microloader C...
Chip: KRONOS
Found Internal MYSTI110 PHY on GMAC0
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
BOX MAC OK!
BOX: Type: ZEE Rev: 75500100
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 600 ms since POR

 

 

 

 

 

 

 

 

 

 

 


--------------------------------------------------------------------------------
| U-Boot 2009.08-00068-g69a4049 (Dec 10 2015 - 14:51:59)               CST HDx |
|------------------------------------------------------------------------------|
| Chipset information                                                          |
| Vendor: Entropic  Type: KRONOS           Revision: B0        Fuses: 00010001 |
|------------------------------------------------------------------------------|
| Clock information                                                            |
| *** not available yet ***                                                    |
|------------------------------------------------------------------------------|
| Frontpanel information                                                       |
| Vendor: CST       Version: 3.3           Display: OLED (128 x 64 px)         |
|------------------------------------------------------------------------------|
| Memory configuration                                                         |
| Start    | End      | Type    | Description                                  |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 1FFFFFFF | RAM     | System main memory bank #0 (512M)            |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K x  64)      |
  *** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit               |
|------------------------------------------------------------------------------|
| Network configuration                                                        |
| MAC: LIP 6300                    address: 00-C5-5C-25-BA-B7                  |
--------------------------------------------------------------------------------

Hit any key to stop autoboot:  0

SFC read: offset 0x100000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Coolstream Kernel (compressed)
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2981377 Bytes =  2.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.10.93 (image@server) (gcc version 6.3.1 20170109 (crosstool-NG 1) ) #1 SMP Sun Apr 15 15:27:43 CEST 2018
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Entropic Kronos STB Platform with FDT, model: CoolStream HD2 Kronos STB
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Early platform io descriptors mapping...
[    0.000000] PERCPU: Embedded 7 pages/cpu @80da8000 s5952 r8192 d14528 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072

BusyBox v1.30.1 (2019-06-22 15:09:50 CEST) built-in shell (ash)

CST-25BAB7:/# Starting Microloader ASM built on Mar 28 2016 18:03:24...
-/bin/sh: Starting: not found
CST-25BAB7:/# Initializing PLLs...
-/bin/sh: Initializing: not found
CST-25BAB7:/# Initializing Clocks..
-/bin/sh: Initializing: not found
CST-25BAB7:/# Initializing DDR PLLs/Clocks...
-/bin/sh: Initializing: not found
CST-25BAB7:/# Initializing DDR controller...
-/bin/sh: Initializing: not found
CST-25BAB7:/# Initializing data section...
-/bin/sh: Initializing: not found
CST-25BAB7:/# Initializing stack ptr...
-/bin/sh: Initializing: not found
CST-25BAB7:/# Starting Microloader C...
-/bin/sh: Starting: not found
CST-25BAB7:/# Chip: KRONOS
-/bin/sh: Chip:: not found
CST-25BAB7:/# Found Internal MYSTI110 PHY on GMAC0
-/bin/sh: Found: not found
CST-25BAB7:/# Checking for Guide button press ...
-/bin/sh: Checking: not found
CST-25BAB7:/# GCS in ISA MODE
-/bin/sh: GCS: not found
CST-25BAB7:/# GCS: SFC DEVICE SETUP COMPLETE
-/bin/sh: GCS:: not found
CST-25BAB7:/# BOX MAC OK!
-/bin/sh: BOX: not found
CST-25BAB7:/# BOX: Type: ZEE Rev: 75500100
-/bin/sh: BOX:: not found
CST-25BAB7:/# Setting up default ATAG list...
-/bin/sh: Setting: not found
CST-25BAB7:/# Jumping to U-Boot ...
-/bin/sh: Jumping: not found
CST-25BAB7:/# BOOT_TIME: 600 ms since POR
-/bin/sh: BOOT_TIME:: not found
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/#
CST-25BAB7:/# ------------------------------------------------------------------
--------------
-/bin/sh: --------------------------------------------------------------------------------: not found
CST-25BAB7:/# | U-Boot 2009.08-00068-g69a4049 (Dec 10 2015 - 14:51:59)
     CST HDx |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# |-----------------------------------------------------------------
-------------|
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# | Chipset information
             |
> | Vendor: Entropic  Type: KRONOS           Revision: B0        Fuses: 00010001
 |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# |-----------------------------------------------------------------
-------------|
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# | Clock information
             |
> | *** not available yet ***
 |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# |-----------------------------------------------------------------
-------------|
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# | Frontpanel information
             |
> | Vendor: CST       Version: 3.3           Display: OLED (128 x 64 px)
 |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# |-----------------------------------------------------------------
-------------|
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# | Memory configuration
             |
> | Start    | End      | Type    | Description
 |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# |----------+----------+---------+---------------------------------
-------------|
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# | 00000000 | 1FFFFFFF | RAM     | System main memory bank #0 (512M
)            |
-/bin/sh: 1FFFFFFF: not found
-/bin/sh: 00000000: not found
-/bin/sh: -: not found
-/bin/sh: System: not found
-/bin/sh: RAM: not found
CST-25BAB7:/# | D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K
 x  64)      |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/#   *** Warning - bad CRC or SFC, using default environment
-/bin/sh: bin: not found
CST-25BAB7:/# | 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit
             |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# |-----------------------------------------------------------------
-------------|
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# | Network configuration
             |
> | MAC: LIP 6300                    address: 00-C5-5C-25-BA-B7
 |
-/bin/sh: syntax error: unexpected "|"
CST-25BAB7:/# ------------------------------------------------------------------
--------------
-/bin/sh: --------------------------------------------------------------------------------: not found
CST-25BAB7:/#
CST-25BAB7:/# Hit any key to stop autoboot:  0
-/bin/sh: Hit: not found
CST-25BAB7:/#
CST-25BAB7:/# SFC read: offset 0x100000, size 0x300000
-/bin/sh: SFC: not found
CST-25BAB7:/#  3145728 bytes read: OK
-/bin/sh: 3145728: not found
CST-25BAB7:/# ## Booting kernel from Legacy Image at 01000000 ...
CST-25BAB7:/#    Image Name:   Coolstream Kernel (compressed)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/#    Image Type:   ARM Linux Kernel Image (uncompressed)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/#    Data Size:    2981377 Bytes =  2.8 MB
-/bin/sh: Data: not found
CST-25BAB7:/#    Load Address: 00008000
-/bin/sh: Load: not found
CST-25BAB7:/#    Entry Point:  00008000
-/bin/sh: Entry: not found
CST-25BAB7:/#    Verifying Checksum ... OK
-/bin/sh: Verifying: not found
CST-25BAB7:/#    Loading Kernel Image ... OK
-/bin/sh: Loading: not found
CST-25BAB7:/# OK
-/bin/sh: OK: not found
CST-25BAB7:/# Uncompressing Linux... done, booting the kernel.
-/bin/sh: Uncompressing: not found
CST-25BAB7:/# [    0.000000] Booting Linux on physical CPU 0x0
sh: missing ]
CST-25BAB7:/# [    0.000000] Initializing cgroup subsys cpuset
sh: missing ]
CST-25BAB7:/# [    0.000000] Linux version 3.10.93 (image@server) (gcc version 6
.3.1 20170109 (crosstool-NG 1) ) #1 SMP Sun Apr 15 15:27:43 CEST 2018
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7)
, cr=10c53c7d
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT alias
ing instruction cache
sh: missing ]
CST-25BAB7:/# [    0.000000] Machine: Entropic Kronos STB Platform with FDT, mod
el: CoolStream HD2 Kronos STB
sh: missing ]
CST-25BAB7:/# [    0.000000] Memory policy: ECC disabled, Data cache writealloc
sh: missing ]
CST-25BAB7:/# [    0.000000] Early platform io descriptors mapping...
sh: missing ]
CST-25BAB7:/# [    0.000000] PERCPU: Embedded 7 pages/cpu @80da8000 s5952 r8192
d14528 u32768
sh: missing ]
CST-25BAB7:/# [    0.000000] Built 1 zonelists in Zone order, mobility grouping
on.  Total pages: 130048
sh: missing ]
CST-25BAB7:/# [    0.000000] Kernel command line: noinitrd console=ttyS0,115200n
8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128
k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1
) root=mtd:root0 rootfstype=jffs2 rw
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000] Dentry cache hash table entries: 65536 (order: 6, 2
62144 bytes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000] Inode-cache hash table entries: 32768 (order: 5, 13
1072 bytes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000] Memory: 512MB = 512MB total
sh: missing ]
CST-25BAB7:/# [    0.: 247144k/247144k available, 277144k reserved, 0K highmem
sh: missing ]
CST-25BAB7:/# [    0.000000] Virtual kernel memory layout:
sh: missing ]
CST-25BAB7:/# [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000  : 0xfff00000 - 0xfffe0000   ( 896 kB)
-/bin/sh: syntax error: 0 - 0x806e3224   ( 105 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU debugfs-based tracing is enabled.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:350
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] Cortex A9 frequency at 600 MHz
[    0.000000] Initializing Cortex A9 Global Timer at Vir:0xFEA00200, using, at Freq:300 MHz
[    0.000000] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 14316ms
[    0.000000] smp_twd: clock not found -2
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.249862] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    0.292758] pid_max: default: 32768 minimum: 301
[    0.297561] Mount-cache hash table entries: 512
[    0.303983] CPU: Testing write buffer coherency: ok
[    0.309079] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.314707] Setting up static identity map for 0x803c47a0 - 0x803c47f8
[    0.321240] L310 cache controller enabled
[    0.325158] l2x0: 8 ways, CACHE_ID 0x410004c7, AUX_CTRL 0x32421001, Cache size: 131072 B
[    0.333783] Brought up 1 CPUs
[    0.336657] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[    0.342981] CPU: All CPU(s) started in SVC mode.
[    0.348245] devtmpfs: initialized
[    0.356639] NET: Registered protocol family 16
[    0.361753] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.475139] GMAC0: active interface is 1
[    0.479129] ChipID=0x1000 ChipRevID=0x100
[    0.483229] nx_dmac: Registered with 8 channels
[    0.510019] bio: create slab <bio-0> at 0
[    0.515383] GPIO: base febab000 (phys e06ab000)
[    0.519974] GPIO: base feb69000 (phys e0669000)
[    0.526358] SCSI subsystem initialized
[    0.531482] usbcore: registered new interface driver usbfs
[    0.537065] usbcore: registered new interface driver hub
[    0.542721] usbcore: registered new device driver usb
[    0.548157] pps_core: LinuxPPS API ver. 1 registered
[    0.553080] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.562363] PTP clock support registered
[    0.567932] cfg80211: Calling CRDA to update world regulatory domain
[    0.575726] Switching to clocksource arm_global_timer
[    0.599560] NET: Registered protocol family 2
[    0.604685] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.611749] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.618153] TCP: Hash tables configured (established 4096 bind 4096)
[    0.624476] TCP: reno registered
[    0.627617] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.633439] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.639880] NET: Registered protocol family 1
[    0.644492] RPC: Registered named UNIX socket transport module.
[    0.650368] RPC: Registered udp transport module.
[    0.654968] RPC: Registered tcp transport module.
[    0.659634] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.666226] PM: STB Platform power mgmt initialization.
[    0.797202] NFS: Registering the id_resolver key type
[    0.802279] Key type id_resolver registered
[    0.806359] Key type id_legacy registered
[    0.810381] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.816753] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.824728] msgmni has been set to 482
[    0.829765unexpected "("
CST-25BAB7:/# [    0.000000]     vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000]     lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000]       .text : 0x80008000 - 0x806584f8   (6466 kB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000]       .init : 0x80659000 - 0x80687740   ( 186 kB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000]       .data : 0x80688000 - 6c8e60   ( 260 kB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000]        .bss : 0x806c8e60 - 0x806e3224   ( 105 kB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1,
Nodes=1
sh: missing ]
CST-25BAB7:/# [    0.000000] Hierarchical RCU implementation.
sh: missing ]
CST-25BAB7:/# [    0.000000]  RCU debugfs-based tracing is enabled.
sh: missing ]
CST-25BAB7:/# [    0.000000]  Additional per-CPU info printed with stalls.
sh: missing ]
CST-25BAB7:/# [    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=
1.
sh: missing ]
CST-25BAB7:/# [    0.000000] NR_IRQS:350
sh: missing ]
CST-25BAB7:/# [    0.000000] GIC CPU mask not found - kernel will fail to boot.
sh: missing ]
CST-25BAB7:/# [    0.000000] GIC CPU mask not found - kernel will fail to boot.
sh: missing ]
CST-25BAB7:/# [    0.000000] Cortex A9 frequency at 600 MHz
sh: missing ]
CST-25BAB7:/# [    0.000000] Initializing Cortex A9 Global Timer at Vir:0xFEA002
00, using, at Freq:300 MHz
sh: missing ]
CST-25BAB7:/# [    0.000000] sched_clock: 32 bits at 300MHz, resolution 3ns, wra
ps every 14316ms
sh: missing ]
CST-25BAB7:/# [    0.000000] smp_twd: clock not found -2
sh: missing ]
CST-25BAB7:/# [    0.000000] Console: colour dummy device 80x30
sh: missing ]
CST-25BAB7:/# [    0.000000] console [ttyS0] enabled
sh: missing ]
CST-25BAB7:/# [    0.249862] Calibrating delay loop... 1196.85 BogoMIPS (lpj=598
4256)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.292758] pid_max: default: 32768 minimum: 301
sh: missing ]
CST-25BAB7:/# [    0.297561] Mount-cache hash table entries: 512
sh: missing ]
CST-25BAB7:/# [    0.303983] CPU: Testing write buffer coherency: ok
sh: missing ]
CST-25BAB7:/# [    0.309079] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
sh: missing ]
CST-25BAB7:/# [    0.314707] Setting up static identity map for 0x803c47a0 - 0x8
03c47f8
sh: missing ]
CST-25BAB7:/# [    0.321240] L310 cache controller enabled
sh: missing ]
CST-25BAB7:/# [    0.325158] l2x0: 8 ways, CACHE_ID 0x410004c7, AUX_CTRL 0x32421
001, Cache size: 131072 B
sh: missing ]
CST-25BAB7:/# [    0.333783] Brought up 1 CPUs
sh: missing ]
CST-25BAB7:/# [    0.336657] SMP: Total of 1 processors activated (1196.85 BogoM
IPS).
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.342981] CPU: All CPU(s) started in SVC mode.
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.348245] devtmpfs: initialized
sh: missing ]
CST-25BAB7:/# [    0.356639] NET: Registered protocol family 16
sh: missing ]
CST-25BAB7:/# [    0.361753] DMA: preallocated 256 KiB pool for atomic coherent
allocations
sh: missing ]
CST-25BAB7:/# [    0.475139] GMAC0: active interface is 1
sh: missing ]
CST-25BAB7:/# [    0.479129] ChipID=0x1000 ChipRevID=0x100
sh: missing ]
CST-25BAB7:/# [    0.483229] nx_dmac: Registered with 8 channels
sh: missing ]
CST-25BAB7:/# [    0.510019] bio: create slab <bio-0> at 0
-/bin/sh: can't open bio-0: no such file
CST-25BAB7:/# [    0.515383] GPIO: base febab000 (phys e06ab000)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.519974] GPIO: base feb69000 (phys e0669000)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.526358] SCSI subsystem initialized
sh: missing ]
CST-25BAB7:/# [    0.531482] usbcore: registered new interface driver usbfs
sh: missing ]
CST-25BAB7:/# [    0.537065] usbcore: registered new interface driver hub
sh: missing ]
CST-25BAB7:/# [    0.542721] usbcore: registered new device driver usb
sh: missing ]
CST-25BAB7:/# [    0.548157] pps_core: LinuxPPS API ver. 1 registered
sh: missing ]
CST-25BAB7:/# [    0.553080] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
 Rodolfo Giometti <giometti@linux.it>
-/bin/sh: syntax error: unexpected newline
CST-25BAB7:/# [    0.562363] PTP clock support registered
sh: missing ]
CST-25BAB7:/# [    0.567932] cfg80211: Calling CRDA to update world regulatory d
omain
sh: missing ]
CST-25BAB7:/# [    0.575726] Switching to clocksource arm_global_timer
sh: missing ]
CST-25BAB7:/# [    0.599560] NET: Registered protocol family 2
sh: missing ]
CST-25BAB7:/# [    0.604685] TCP established hash table entries: 4096 (order: 3,
 32768 bytes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.611749] TCP bind hash table entries: 4096 (order: 3, 32768
bytes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.618153] TCP: Hash tables configured (established 4096 bind
4096)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.624476] TCP: reno registered
sh: missing ]
CST-25BAB7:/# [    0.627617] UDP hash table entries: 256 (order: 1, 8192 bytes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.633439] UDP-Lite hash table entries: 256 (order: 1, 8192 by
tes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.639880] NET: Registered protocol family 1
sh: missing ]
CST-25BAB7:/# [    0.644492] RPC: Registered named UNIX socket transport module.
sh: missing ]
CST-25BAB7:/# [    0.650368] RPC: Registered udp transport module.
sh: missing ]
CST-25BAB7:/# [    0.654968] RPC: Registered tcp transport module.
sh: missing ]
CST-25BAB7:/# [    0.659634] RPC: Registered tcp NFSv4.1 backchannel transport m
odule.
sh: missing ]
CST-25BAB7:/# [    0.666226] PM: STB Platform power mgmt initialization.
sh: missing ]
CST-25BAB7:/# [    0.797202] NFS: Registering the id_resolver key type
sh: missing ]
CST-25BAB7:/# [    0.802279] Key type id_resolver registered
sh: missing ]
CST-25BAB7:/# [    0.806359] Key type id_legacy registered
sh: missing ]
CST-25BAB7:/# [    0.810381] Installing knfsd (copyright (C) 1996 okir@monad.swb
.de).
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.816753] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006
Red Hat, Inc.
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.824728] msgmni has been set to 482
sh: missing ]
CST-25BAB7:/# [    0.829765] Block layer SCSI generic (bsg) driver version 0.4 l
oaded (major 252)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.837125] io scheduler noop registere840977] io scheduler dea
dline registered
sh: missing ]
CST-25BAB7:/# [    0.845839] io scheduler cfq registered (default)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.851209] e06b2000.serial: ttyS0 at MMIO 0xe06b2000 (irq = 47
) is a uart-ip3106
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.865585] loop: module loaded
sh: missing ]
CST-25BAB7:/# [    0.869716] ahci-stb e0638000.sata: unable to find phy
sh: missing ]
CST-25BAB7:/# [    0.874818] SATA: Enable mpll_ss_en (rd_val=0x571185, wr_val=0x
5711a5)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.881253] SATA: Enable rx_term_en0 (rd_val=0x277, wr_val=0x27
7)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.887317] ahci-stb e0638000.sata: SSS flag set, parallel bus
scan disabled
sh: missing ]
CST-25BAB7:/# [    0.894325] ahci-stb e0638000.sata: AHCI 0001.0300 32 slots 1 p
orts 3 Gbps 0x1 impl platform mode
sh: missing ]
CST-25BAB7:/# [    0.903113] ahci-stb e0638000.sata: ags: ncq sntf stag pm led c
lo only pmp pio slum part ccc apst
00 : "root0"
[    0.985757] 0x000010000000-0x000012000000 : "var"
[    0.991851] 0x000012000000-0x000020000000 : "root1"
[    1.000185] JEDEC ID = 0x1c3016 , Extended Device ID = 0x1c30
[    1.005931] nx_sfc e0632000.flash_sfc: en25q32 (4096 Kbytes)
[    1.011572] 5 cmdlinepart partitions found on MTD device e0632000.flash_sfc
[    1.018446] Creating 5 MTD partitions on "e0632000.flash_sfc":
[    1.024260] 0x000000000000-0x000000040000 : "uldr"
[    1.030646] 0x000000040000-0x0000000c0000 : "u-boot"
[    1.036952] 0x0000000c0000-0x0000000e0000 : "env"
[    1.043086] 0x0000000e0000-0x000000100000 : "spare"
[    1.049323] 0x000000100000-0x000000400000 : "kernel"
[    1.056379] tun: Universal TUN/TAP device driver, 1.6
[    1.061405] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.068051]  DWMAC1000
[    1.070350] stmmac - user ID: 0x36, Synopsys ID: 0x36
[    1.075329]  Ring mode enabled
[    1.078354]  DMA HW capability register supported
[    1.082866]  Enhanced/Alternate descriptors
[    1.087166]  Enabled extended descriptors
[    1.091151]  RX Checksum Offload Engine supported (type 2)
[    1.096584]  TX Checksum insertion supported
[    1.100824]  Wake-Up On Lan supported
[    1.104489]  Enable RX Mitigation via HW Watchdog Timer
[    1.124471] libphy: stmmac: probed
[    1.127791] eth0: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) active
[    1.134167] eth0: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
[    1.139806] eth0: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
[    1.145526] eth0: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
[    1.151224] eth0: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
[    1.156913] eth0: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
[    1.162622] eth0: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
[    1.168317] eth0: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
[    1.174026] eth0: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
[    1.179722] eth0: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
[    1.185430] eth0: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
[    1.191219] eth0: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
[    1.197002] eth0: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
[    1.202797] eth0: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
[    1.208579] eth0: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
[    1.214374] eth0: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
[    1.220163] eth0: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
[    1.225945] eth0: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
[    1.231740] eth0: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
[    1.237524] eth0: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
[    1.243317] eth0: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
[    1.249100] eth0: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
[    1.254896] eth0: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
[    1.260683] eth0: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
[    1.266467] eth0: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
[    1.272262] eth0: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
[    1.278045] eth0: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
[    1.283840] eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
[    1.289622] eth0: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
[    1.295416] eth0: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
[    1.301205] eth0: PHY ID 00000000 at 30 IRQsh: missing ]
CST-25BAB7:/# [    0.912581] ata4294967295: SATA PHY offline
sh: missing ]
CST-25BAB7:/# [    0.917602] scsi0 : ahci_platform
sh: missing ]
CST-25BAB7:/# [    0.921555] ata1: SATA max UDMA/133 mmio [mem 0xe0638000-0xe063
8fff] port 0x100 irq 39
sh: missing ]
CST-25BAB7:/# [    0.931025] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (
Toshiba NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    0.943425] Bad block table found at page 262080, version 0x01
sh: missing ]
CST-25BAB7:/# [    0.949940] Bad block table found at page 262016, version 0x01
sh: missing ]
CST-25BAB7:/# [    0.956197] nand_read_bbt: bad block at 0x00001cf60000
sh: missing ]
CST-25BAB7:/# [    0.961260] nand_read_bbt: bad block at 0x00001cfa0000
sh: missing ]
CST-25BAB7:/# [    0.966387] 3 cmdlinepart partitions found on MTD device e06310
00.flash_nand
sh: missing ]
CST-25BAB7:/# [    0.973341] Creating 3 MTD partitions on "e0631000.flash_nand":
sh: missing ]
CST-25BAB7:/# [    0.979207] 0x000000000000-0x000010000000 : "root0"
sh: missing ]
CST-25BAB7:/# [    0.985757] 0x000010000000-0x000012000000 : "var"
sh: missing ]
CST-25BAB7:/# [    0.991851] 0x000012000000-0x000020000000 : "root1"
sh: missing ]
CST-25BAB7:/# [    1.000185] JEDEC ID = 0x1c3016 , Extended Device ID = 0x1c30
sh: missing ]
CST-25BAB7:/# [    1.005931] nx_sfc e0632000.flash_sfc: en25q32 (4096 Kbytes)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.011572] 5 cmdlinepart partitions found on MTD device e06320
00.flash_sfc
sh: missing ]
CST-25BAB7:/# [    1.018446] Creating 5 MTD partitions on "e0632000.flash_sfc":
sh: missing ]
CST-25BAB7:/# [    1.024260] 0x000000000000-0x000000040000 : "uldr"
sh: missing ]
CST-25BAB7:/# [    1.030646] 0x000000040000-0x0000000c0000 : "u-boot"
sh: missing ]
CST-25BAB7:/# [    1.036952] 0x0000000c0000-0x0000000e0000 : "env"
sh: missing ]
CST-25BAB7:/# [    1.043086] 0x0000000e0000-0x000000100000 : "spare"
sh: missing ]
CST-25BAB7:/# [    1.049323] 0x000000100000-0x000000400000 : "kernel"
sh: missing ]
CST-25BAB7:/# [    1.056379] tun: Universal TUN/TAP device driver, 1.6
sh: missing ]
CST-25BAB7:/# [    1.061405] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.c
om>
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.068051]  DWMAC1000
sh: missing ]
CST-25BAB7:/# [    1.070350] stmmac - user ID: 0x36, Synopsys ID: 0x36
sh: missing ]
CST-25BAB7:/# [    1.075329]  Ring mode enabled
sh: missing ]
CST-25BAB7:/# [    1.078354]  DMA HW capability register supported
sh: missing ]
CST-25BAB7:/# [    1.082866]  Enhanced/Alternate descriptors
sh: missing ]
CST-25BAB7:/# [    1.087166]  Enabled extended descriptors
sh: missing ]
CST-25BAB7:/# [    1.091151]  RX Checksum Offload Engine supported (type 2)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.096584]  TX Checksum insertion supported
sh: missing ]
CST-25BAB7:/# [    1.100824]  Wake-Up On Lan supported
sh: missing ]
CST-25BAB7:/# [    1.104489]  Enable RX Mitigation via HW Watchdog Timer
sh: missing ]
CST-25BAB7:/# [    1.124471] libphy: stmmac: probed
sh: missing ]
CST-25BAB7:/# [    1.127791] eth0: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) a
ctive
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.134167] eth0: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.139806] eth0: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.145526] eth0: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.151224] eth0: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.156913] eth0: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.162622] eth0: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.168317] eth0: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.174026] eth0: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.179722] eth0: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.185430] eth0: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.191219] eth0: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.197002] eth0: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.202797] eth0: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.208579] eth0: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.214374] eth0: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.220163] eth0: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.225945] eth0: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.231740] eth0: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.237524] eth0: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.243317] eth0: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.249100] eth0: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.254896] eth0: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.260683] eth0: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.266467] eth0: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.272262] eth0: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.278045] eth0: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.283840] eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.289622] eth0: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.295416] eth0: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.301205] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.306988] eth0: PHY ID 00000000 at 31 I POLL (stmmac-0:1f)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.313044] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
 Driver
-/bin/sh: syntax error: unexpected "("
366240] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.372950] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.380103] usb usb1: Product: EHCI Host Controller
[    1.384923] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.390383] usb usb1: SerialNumber: e066c000.usb
[    1.395860] hub 1-0:1.0: USB hub found
[    1.399534] hub 1-0:1.0: 1 port detected
[    1.403709] ehci-platform e066d000.usb: EHCI Host Controller
[    1.409280] ehci-platform e066d000.usb: new USB bus registered, assigned bus number 2
[    1.417194] ehci-platform e066d000.usb: irq 94, io mem 0xe066d000
[    1.423247] ata1: SATA PHY offline
[    1.426571] ata1: SATA link down (SStatus 0 SControl 300)
[    1.440078] ehci-platform e066d000.usb: USB 2.0 started, EHCI 1.00
[    1.446233] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.452945] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.460101] usb usb2: Product: EHCI Host Controller
[    1.464921] usb usb2: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.470375] usb usb2: SerialNumber: e066d000.usb
[    1.475761] hub 2-0:1.0: USB hub found
[    1.479435] hub 2-0:1.0: 1 port detected
[    1.484046] usbcore: registered new interface driver usb-storage
[    1.490439] usbcore: registered new interface driver usbserial
[    1.497743] usbcore: registered new interface driver usbhid
[    1.503283] usbhid: USB HID core driver
[    1.507270] TCP: cubic registered
[    1.510517] NET: Registered protocol family 17
[    1.515327] Key type dns_resolver registered
[    1.519602] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 3
[    1.527137] ThumbEE CPU extension supported.
[    1.532426] ### dt-test ### No testcase data in device tree; not running tests
[    1.730080] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.881640] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    1.888259] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.895349] usb 1-1: Product: USB2.0 Hub
[    1.900632] hub 1-1:1.0: USB hub found
[    1.904641] hub 1-1:1.0: 4 ports detected
[    2.600058] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    2.752190] usb 2-1: New USB device found, idVendor=174c, idProduct=5136
[    2.758805] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    2.765890] usb 2-1: Product: AS2105
[    2.769415] usb 2-1: Manufacturer: ASMedia
[    2.773483] usb 2-1: SerialNumber: 00000000000000000000
[    2.779840] usb-storage 2-1:1.0: USB Mass Storage device detected
[    2.786109] scsi1 : usb-storage 2-1:1.0
[    3.791054] scsi 1:0:0:0: Direct-Access     ASMT     2105             0    PQ: 0 ANSI: 6
[    3.800888] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    4.624990] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[    4.633348] sd 1:0:0:0: [sda] Write Protect is off
[    4.638842] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    4.673503]  sda: sda1
[    4.679350] sd 1:0:0:0: [sda] Attached SCSI disk
[    6.959898] VFS: Mounted root (jffs2 filesystem) on device 31:0.
[    6.967185] devtmpfs: mounted
[    6.970351] Freeing unused kernel memory: 184K (80659000 - 80687000)
init started: BusyBox v1.30.1 (2019-06-22 15:09:50 CEST)
[    7.853314] NET: Registered protocol family 10
try to mount /dev/mtdblock1 to /var
[    8.286337] jffs2: Empty flash at 0x01088ad8 ends at 0x01089000
starting /etc/init.d/S02loadmodules ...
Sat Jan  1 00:00:00 CET 2000
Creating device node for cs_display
Running insmod now .......
Driver modules loaded, please start the app now...
Creating device node for KAL
Creating device node for notifyq
CST-25BAB7:/# [    1.319464] ehci-platformplatform driver

sh: missing ]
CST-25BAB7:/# [    1.324938] ehci-platform e066c000.usb: EHCI Host Controller
sh: missing ]
CST-25BAB7:/# [    1.330565] ehci-platform e066c000.usbus registered, assigned b
us number 1
sh: missing ]
CST-25BAB7:/# [    1.338383] ehci-platform e066c000.usb: irq 93, io mem 0xe066c0
00
sh: missing ]
CST-25BAB7:/# [    1.360091] e-platform e066c000.usb: USB 2.0 started, EHCI 1.00
sh: missing ]
CST-25BAB7:/# [    1.366240] usb usb1: New USB device found, idVendor=1d6b, idPr
oduct=0002
sh: missing ]
CST-25BAB7:/# [    1.372950] usb usb1: New USB device strings: Mfr=3, Product=2,
 SerialNumber=1
sh: missing ]
CST-25BAB7:/# [    1.380103] usb usb1: Product: EHCI Host Controller
sh: missing ]
CST-25BAB7:/# [    1.384923] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
sh: missing ]
CST-25BAB7:/# [    1.390383] usb usb1: SerialNumber: e066c000.usb
sh: missing ]
CST-25BAB7:/# [    1.395860] hub 1-0:1.0: USB hub found
sh: missing ]
CST-25BAB7:/# [    1.399534] hub 1-0:1.0: 1 port detected
sh: missing ]
CST-25BAB7:/# [    1.403709] ehci-platform e066d000.usb: EHCI Host Controller
sh: missing ]
CST-25BAB7:/# [    1.409280] ehci-platform e066d000.usb: new USB bus registered,
 assigned bus number 2
sh: missing ]
CST-25BAB7:/# [    1.417194] ehci-platform e066d000.usb: irq 94, io mem 0xe066d0
00
sh: missing ]
CST-25BAB7:/# [    1.423247] ata1: SATA PHY offline
sh: missing ]
CST-25BAB7:/# [    1.426571] ata1: SATA link down (SStatus 0 SControl 300)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    1.440078] ehci-platform e066d000.usb: USB 2.0 started, EHCI 1
.00
sh: missing ]
CST-25BAB7:/# [    1.446233] usb usb2: New USB device found, idVendor=1d6b, idPr
oduct=0002
sh: missing ]
CST-25BAB7:/# [    1.452945] usb usb2: New USB device strings: Mfr=3, Product=2,
 SerialNumber=1
sh: missing ]
CST-25BAB7:/# [    1.460101] usb usb2: Product: EHCI Host Controller
sh: missing ]
CST-25BAB7:/# [    1.464921] usb usb2: Manufacturer: Linux 3.10.93 ehci_hcd
sh: missing ]
CST-25BAB7:/# [    1.470375] usb usb2: SerialNumber: e066d000.usb
sh: missing ]
CST-25BAB7:/# [    1.475761] hub 2-0:1.0: USB hub found
sh: missing ]
CST-25BAB7:/# [    1.479435] hub 2-0:1.0: 1 port detected
sh: missing ]
CST-25BAB7:/# [    1.484046] usbcore: registered new interface driver usb-storag
e
sh: missing ]
CST-25BAB7:/# [    1.490439] usbcore: registered new interface driver usbserial
sh: missing ]
CST-25BAB7:/# [    1.497743] usbcore: registered new interface driver usbhid
sh: missing ]
CST-25BAB7:/# [    1.503283] usbhid: USB HID core driver
sh: missing ]
CST-25BAB7:/# [    1.507270] TCP: cubic registered
sh: missing ]
CST-25BAB7:/# [    1.510517] NET: Registered protocol family 17
sh: missing ]
CST-25BAB7:/# [    1.515327] Key type dns_resolver registered
sh: missing ]
CST-25BAB7:/# [    1.519602] VFP support v0.3: implementor 41 architecture 3 par
t 30 variant 9 rev 3
sh: missing ]
CST-25BAB7:/# [    1.527137] ThumbEE CPU extension supported.
sh: missing ]
CST-25BAB7:/# [    1.532426] ### dt-test ### No testcase data in device tree; no
t running tests
sh: missing ]
CST-25BAB7:/# [    1.730080] usb 1-1: new high-speed USB device number 2 using e
hci-platform
sh: missing ]
CST-25BAB7:/# [    1.881640] usb 1-1: New USB device found, idVendor=05e3, idPro
duct=0608
sh: missing ]
CST-25BAB7:/# [    1.888259] usb 1-1: New USB device strings: Mfr=0, Product=1,
SerialNumber=0
sh: missing ]
CST-25BAB7:/# [    1.895349] usb 1-1: Product: USB2.0 Hub
sh: missing ]
CST-25BAB7:/# [    1.900632] hub 1-1:1.0: USB hub found
sh: missing ]
CST-25BAB7:/# [    1.904641] hub 1-1:1.0: 4 ports detected
sh: missing ]
CST-25BAB7:/# [    2.600058] usb 2-1: new high-speed USB device number 2 using e
hci-platform
sh: missing ]
CST-25BAB7:/# [    2.752190] usb 2-1: New USB device found, idVendor=174c, idPro
duct=5136
sh: missing ]
CST-25BAB7:/# [    2.758805] usb 2-1: New USB device strings: Mfr=2, Product=3,
SerialNumber=1
sh: missing ]
CST-25BAB7:/# [    2.765890] usb 2-1: Product: AS2105
sh: missing ]
CST-25BAB7:/# [    2.769415] usb 2-1: Manufacturer: ASMedia
sh: missing ]
CST-25BAB7:/# [    2.773483] usb 2-1: SerialNumber: 00000000000000000000
sh: missing ]
CST-25BAB7:/# [    2.779840] usb-storage 2-1:1.0: USB Mass Storage device detect
ed
sh: missing ]
CST-25BAB7:/# [    2.786109] scsi1 : usb-storage 2-1:1.0
sh: missing ]
CST-25BAB7:/# [    3.791054] scsi 1:0:0:0: Direct-Access     ASMT     2105
       0    PQ: 0 ANSI: 6
sh: missing ]
CST-25BAB7:/# [    3.800888] sd 1:0:0:0: Attached scsi generic sg0 type 0
sh: missing ]
CST-25BAB7:/# [    4.624990] sd 1:0:0:0: [sda] 1953525168 512-byte logical block
s: (1.00 TB/931 GiB)
-/bin/sh: syntax error: unexpected "("
CST-25BAB7:/# [    4.633348] sd 1:0:0:0: [sda] Write Protect is off
sh: missing ]
CST-25BAB7:/# [    4.638842] sd 1:0:0:0: [sda] Write cache: enabled, read cache:
 enabled, doesn't support DPO or FUA
> [    4.673503]  sda: sda1
> [    4.679350] sd 1:0:0:0: [sda] Attached SCSI disk
> [    6.959898] VFS: Mounted root (jffs2 filesystem) on device 31:0.
> [    6.967185] devtmpfs: mounted
> [    6.970351] Freeing unused kernel memory: 184K (80659000 - 80687000)
> init started: BusyBox v1.30.1 (2019-06-22 15:09:50 CEST)
> [    7.853314] NET: Registered protocol family 10
> try to mount /dev/mtdblock1 to /var
> [    8.286337] jffs2: Empty flash at 0x01088ad8 ends at 0x01089000
> starting /etc/init.d/S02loadmodules ...
> Sat Jan  1 00:00:00 CET 2000
> Creating device node for cs_display
> Running insmod now .......
> Driver modules loaded, please start the app now...
> Creating device node for KAL
> Creating device node for notifyq
> Creating device node for platform
> Creating d
> Creating device node for standby
> Creating device node for video
> Creating device node for audio
> Creating device node for pvr
> Creating device node for ci
> Creating device node for cs_control
> Creating device node for cs_ir
> Creating device node for fb
> starting /etc/init.d/S04mdev ...
> [logoview] done with Timeout...
> error connect socket /tmp/neutrino.sock: No such file or directory
> starting /etc/init.d/S05mount ...
> starting /etc/init.d/S50hostname ...
> starting /etc/init.d/S51networking ...
> Configuring network interfaces... Starting wlan0
> Failed to connect to wpa_supplicant - wpa_ctrl_open: Success
> Could not read interface wlan0 flags: No such device
> Failed to initialize driver interface
> done.
> starting /etc/init.d/S52syslogd ...
> Jan  1 00:00:14 CST-25BAB7 syslog.info syslogd started: BusyBox v1.30.1
> starting /etc/init.d/S60autofs ...
>  1 Jan 00:00:14 ntpdate[1137]: ntpdate 4.2.8p6@1.3265-o (1)
> starting
> starting /etc/init.d/S80dvdreadfs ...
> starting /etc/init.d/S90inetd ...
> starting /etc/init.d/S96nfsd ...
> starting /var/etc/init.d/S9T_tuxcald ...
> starting /var/etc/init.d/S9T_tuxmaild ...
> Jan  1 00:00:15 CST-25BAB7 daemon.info : starting pid 1173, tty '': '/etc/init
.d/start_neutrino'
>
> Please press Enter to activate this console. /var/plugins/operations camd_init
> /var/plugins/operations cardserver_start
> starte doscam
> Sat Jan  1 00:00:16 CET 2000
> /var/plugins/operations camd_start
> /var/plugins/operations rezap
> 30 Dec 12:56:21 ntpdate[1137]: step time server 130.133.1.10 offset 631025765.
066037 sec
> /var/plugins/operations: line 262: 6: not found
> [frontend.cpp:Open:284] /dev/dvb/adapter0/frontend2: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter0/frontend3: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend0: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend1: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend2: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend3: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend0: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend1: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend2: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend3: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend0: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend1: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend2: No such file or directory
> [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend3: No such file or directory
> MON: The POD Monitor task has started. Version = 01, Release = 00, Subrelease
= 01, PID: 1213
> MON: Initializing
> slot->inbound_queue : 76076070
> slot->outbound_queue: 76075f18
> xport_command_queue: 76075d00
> MON: Start resource providers...
> XPORT: POD Transport task started. PID: 1213
> RM: Resource Manager thread started. PID: 1213
> XPORT: transport connection #1 set to Idle
> LINK: POD link task started with arg=0x00000000, PID: 1213
> MON: Starting 9 resource(s).
> MON starting 9 resources finished
> MON after BR_POD_mon_start_rps
> POD timer thread PID: 1213
> comming in  add resource provider, rid=10041
> RM before wait for db ready, pid: 1213
> APPMMI thread starts, PID: 1213
> UPGRADE thread is started, PID: 1213
> comming in  add resource provider, rid=8e1001
> HOSTCTRL thread is started, PID: 1213
> comming in  add resource provider, rid=200041
> SYSTIME resource start, PID: 1213
> comming in  add resource provider, rid=240041
> SYSTIME RP: System Time main loop processing started.
> CA resource provider started with arg=0x00000000, PID: 1213
> APPINFO thread starts, PID: 1213
> comming in  add resource provider, rid=20043
> APPINFO RP: resource provider is added, resource ID :0x20043
> APPINFO RP: APPINFO resource provider main loop processing started.
> RM after wait for db ready, pid: 1213
> HOSTLANG_CNTY thread is started, PID: 1213
> comming in  add resource provider, rid=8d1001
> MMI thread is started, PID: 1213
> comming in  add resource provider, rid=400041
> CP resource start, PID: 1213
> CP thread get delay time 0(s)
> CP: Start of initialization...
> HOSTCTRL RP: resource provider is added
> ciappReportModuleStatus: status 9, gCardStatus: 0
> PHYS-CI+: cs_ci_init_controller called
> comming in  add resource provider, rid=410041
> UPGRADE RP: resource provider is added
> UPGRADE RP: UPGRADE resource provider main loop processing started.
> RM: Resource Manager message processing started.
> comming in  add resource provider, rid=30041
> CA RP: Resource Provider main loop processing started.
> HOSTLANG_CNTY RP: resource provider is added
> MON after wait event
> MON: Wait for all required resource providers to sign on....

2019-12-30 12:56:34.088 [sectionsd] commandserviceStopped done
2019-12-30 12:56:34.130 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:34.302 [sectionsd] timeThread: get DVB time ch 0x00020085000a rc: -1 neutrino_sets_time 0
2019-12-30 12:56:34.309 [sectionsd] timeThread: Time set FAILED (enabled: ntp 0 dvb 1)
sh: you need to specify whom to kill
2019-12-30 12:56:35.030 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:35.070 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:35.344 [sectionsd] timeThread: get DVB time ch 0x00020085000a (isOpen 1)
2019-12-30 12:56:37.935 [sectionsd] timeThread: get DVB time ch 0x00020085000a rc: 8 neutrino_sets_time 0
2019-12-30 12:56:37.944 [sectionsd] SIsectionTIME::parse: TDT time: Mon Dec 30 12:56:36 2019
2019-12-30 12:56:37.949 [sectionsd] timeThread: timediff -1948979, current: 30.12.2019 12:56:37, dvb: Mon Dec 30 12:56:36 2019

2019-12-30 12:56:36.000 [sectionsd] cnThread::run:: time set: Mon Dec 30 12:56:36 2019

2019-12-30 12:56:36.006 [sectionsd] freeSatThread::run:: time set: Mon Dec 30 12:56:36 2019

2019-12-30 12:56:36.011 2019-12-30 12:56:36.011 [sectionsd] timeThread: Time set via DVB (TDT), going to sleep for 5 seconds.
[sectionsd] eitThread::run:: time set: Mon Dec 30 12:56:36 2019

 --- > rezapping
2019-12-30 12:56:36.732 [sectionsd] addEvent: ch 00020085000a running 0 (next) got_CN 0
2019-12-30 12:56:37.681 [sectionsd] addEvent: ch 00020085000a running 4 (curr) got_CN 2
2019-12-30 12:56:37.854 [sectionsd] commandserviceChanged: Service change to 48d200020085000a demux #0
2019-12-30 12:56:37.898 [sectionsd] cnThread: eit update filter, ch 0x00020085000a, current ver 0x0c  got events 3 (not active)
2019-12-30 12:56:41.050 [sectionsd] timeThread: get DVB time ch 0x00020085000a (isOpen 1)
2019-12-30 12:56:42.362 [sectionsd] timeThread: get DVB time ch 0x00020085000a rc: 29 neutrino_sets_time 0
2019-12-30 12:56:42.372 [sectionsd] SIsectionTIME::parse: TOT time: Mon Dec 30 12:56:42 2019
2019-12-30 12:56:42.376 [sectionsd] timeThread: timediff -376291, current: 30.12.2019 12:56:42, dvb: Mon Dec 30 12:56:42 2019

2019-12-30 12:56:42.389 [sectionsd] difference is < 120s, using adjtime(0, -376291). oldd(0, 0)
2019-12-30 12:56:42.399 [sectionsd] timeThread: Time set via DVB (TOT), going to sle> APPMMI RP: resource provider is added
> MMI RP: resource provider is added
> HOSTCTRL RP: HOSTCTRL resource provider main loop processing started.
> CP nvram: Root certificate file is for production
> HOSTLANG_CNTY RP: HOSTLANG_CNTY resource provider main loop processing started
.
> LINK: hard reset complete.
> LINK: slot #0 state = BR_POD_SLOT_NOT_INIT
> MMI RP: MMI resource provider main loop processing started.
> APPMMI RP: APPMMI resource provider main loop processing started.
> dump mbuf....
> LINK: slot #0 state = BR_POD_SLOT_CARD_NOT_PRESENT
> RM: recvd LINK_STATUS tag(0x42), len=8
> RM: No host-pod interface
> RM: close all connections on slot 0
> LINK: after bypass card
> dump mbuf....
> ciappReportModuleStatus: status 0, gCardStatus: 0
> dump mbuf....
> no CICAM brand id extension.
> comming in  add resource provider, rid=8c1001
> RM: recvd RM_RESOURCES_CHANGED tag(0x43), len=8
> CP RP: resource provider is added
> CP: Resource Provider main loop processing started.
> 2019-12-30 12:56:32.396 [sectionsd] start
> 2019-12-30 12:56:32.522 [sectionsd] starting
> 2019-12-30 12:56:32.689 [sectionsd] timeThread::run:: starting, pid 1213 (1672
021168)
> 2019-12-30 12:56:32.796 [sectionsd] eitThread::run:: starting, pid 1213 (16699
24016)
> 2019-12-30 12:56:32.811 [sectionsd] cnThread::run:: starting, pid 1213 (166782
6864)
> 2019-12-30 12:56:32.821 [sectionsd] timeThread: get DVB time ch 0x000000000000
 (isOpen 1)
> 2019-12-30 12:56:32.851 [sectionsd] freeSatThread::run:: starting, pid 1213 (1
665729712)
> [ConfigFile] Unable to open file /var/tuxbox/config/bookmarks for reading.
> 2019-12-30 12:56:34.040 [sectionsd] commandserviceStopped
> 2019-12-30 12:56:34.085 [sectionsd] cnThread: stop eit update filter (not acti
ve)
> 2019-12-30 12:56:34.088 [sectionsd] commandserviceStopped done
> 2019-12-30 12:56:34.130 [sectionsd] commandserviceChanged: Service change to 4
8d200020085000a demux #0
> 2019-12-30 12:56:34.302 [sectionsd] timeThread: get DVB time ch 0x00020085000a
 rc: -1 neutrino_sets_time 0
> 2019-12-30 12:56:34.309 [sectionsd] timeThread: Time set FAILED (enabled: ntp
0 dvb 1)
> sh: you need to specify whom to kill
> 2019-12-30 12:56:35.030 [sectionsd] commandserviceChanged: Service change to 4
8d200020085000a demux #0
> 2019-12-30 12:56:35.070 [sectionsd] commandserviceChanged: Service change to 4
8d200020085000a demux #0
> 2019-12-30 12:56:35.344 [sectionsd] timeThread: get DVB time ch 0x00020085000a
 (isOpen 1)
> 2019-12-30 12:56:37.935 [sectionsd] timeThread: get DVB time ch 0x00020085000a
 rc: 8 neutrino_sets_time 0
> 2019-12-30 12:56:37.944 [sectionsd] SIsectionTIME::parse: TDT time: Mon Dec 30
 12:56:36 2019
> 2019-12-30 12:56:37.949 [sectionsd] timeThread: timediff -1948979, current: 30
.12.2019 12:56:37, dvb: Mon Dec 30 12:56:36 2019
>
> 2019-12-30 12:56:36.000 [sectionsd] cnThread::run:: time set: Mon Dec 30 12:56
:36 2019
>
> 2019-12-30 12:56:36.006 [sectionsd] freeSatThread::run:: time set: Mon Dec 30
12:56:36 2019
>
> 2019-12-30 12:56:36.011 2019-12-30 12:56:36.011 [sectionsd] timeThread: Time s
et via DVB (TDT), going to sleep for 5 seconds.
> [sectionsd] eitThread::run:: time set: Mon Dec 30 12:56:36 2019
>
>  --- > rezapping
> 2019-12-30 12:56:36.732 [sectionsd] addEvent: ch 00020085000a running 0 (next)
 got_CN 0
> 2019-12-30 12:56:37.681 [sectionsd] addEvent: ch 00020085000a running 4 (curr)
 got_CN 2
> 2019-12-30 12:56:37.854 [sectionsd] commandserviceChanged: Service change to 4
8d200020085000a demux #0
> 2019-12-30 12:56:37.898 [sectionsd] cnThread: eit update filter, ch 0x00020085
000a, current ver 0x0c  got events 3 (not active)
> 2019-12-30 12:56:41.050 [sectionsd] timeThread: get DVB time ch 0x00020085000a
 (isOpen 1)
> 2019-12-30 12:56:42.362 [sectionsd] timeThread: get DVB time ch 0x00020085000a
 rc: 29 neutrino_sets_time 0
> 2019-12-30 12:56:42.372 [sectionsd] SIsectionTIME::parse: TOT time: Mon Dec 30
 12:56:42 2019
> 2019-12-30 12:56:42.376 [sectionsd] timeThread: timediff -376291, current: 30.
12.2019 12:56:42, dvb: Mon Dec 30 12:56:42 2019
>
> 2019-12-30 12:56:42.389 [sectionsd] difference is < 120s, using adjtime(0, -37
6291). oldd(0, 0)
> 2019-12-30 12:56:42.399 [sectionsd] timeThread: Time set via DVB (TOT), going
to sleep for 1800 seconds.

Mfg Skyline666

 

 

 

bearbeitet von Gandal
Bitte Spoiler-Tag's verwenden, Danke.

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen
vor einer Stunde schrieb Don de Deckelwech:

Hi,

flashe mal neu, das Bootlog sieht nicht wirklich gesund aus.

 

Ciao,

DdD.

 

Meinst Du das ganze Image oder nur einen Teil wie den Kernel etc?

 

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen

Wie @DdD schon festgestellt hat sieht das Bootlog nicht wirklich gut aus, nochmal Flashen ( Komplettes Image ) und dann testen wie empfohlen wäre auch mein Tip gewesen.

 

Das dadurch das HDMI Problem behoben wird glaube ich allerdings nicht aber mal abwarten.

 

Sollte es nach dem neuerlichen Flashen noch immer Probleme mit dem HDMI Ausgang geben dann ist der Chip hier defekt.

https://www.onsemi.com/pub/Collateral/CM2020-00TR-D.PDF

 

 

 

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen
vor einer Stunde schrieb skyline666:

 

Meinst Du das ganze Image oder nur einen Teil wie den Kernel etc?

 

 

Und hier nach einem kompletten Online Image Flash! Die Einstellungen sind aber alle übernommen worden.

Damit Favoriten und Videoeinstellungen alle identisch.

 


Starting Microloader ASM built on Mar 28 2016 18:03:24...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Starting Microloader C...
Chip: KRONOS
Found Internal MYSTI110 PHY on GMAC0
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
BOX MAC OK!
BOX: Type: ZEE Rev: 75500100
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 599 ms since POR

 

 

 

 

 

 

 

 

 

 

 


--------------------------------------------------------------------------------
| U-Boot 2009.08-00068-g69a4049 (Dec 10 2015 - 14:51:59)               CST HDx |
|------------------------------------------------------------------------------|
| Chipset information                                                          |
| Vendor: Entropic  Type: KRONOS           Revision: B0        Fuses: 00010001 |
|------------------------------------------------------------------------------|
| Clock information                                                            |
| *** not available yet ***                                                    |
|------------------------------------------------------------------------------|
| Frontpanel information                                                       |
| Vendor: CST       Version: 3.3           Display: OLED (128 x 64 px)         |
|------------------------------------------------------------------------------|
| Memory configuration                                                         |
| Start    | End      | Type    | Description                                  |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 1FFFFFFF | RAM     | System main memory bank #0 (512M)            |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K x  64)      |
  *** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit               |
|------------------------------------------------------------------------------|
| Network configuration                                                        |
| MAC: LIP 6300                    address: 00-C5-5C-25-BA-B7                  |
--------------------------------------------------------------------------------

Hit any key to stop autoboot:  0

SFC read: offset 0x100000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Coolstream Kernel (compressed)
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2981377 Bytes =  2.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.10.93 (image@server) (gcc version 6.3.1 20170109                                                                                                      (crosstool-NG 1) ) #1 SMP Sun Apr 15 15:27:43 CEST 2018
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instructio                                                                                                     n cache
[    0.000000] Machine: Entropic Kronos STB Platform with FDT, model: CoolStream                                                                                                      HD2 Kronos STB
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Early platform io descriptors mapping...
[    0.000000] PERCPU: Embedded 7 pages/cpu @80da8000 s5952 r8192 d14528 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                                                                                     es: 130048
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e06                                                                                                     32000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),                                                                                                     -(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:roo                                                                                                     t0 rootfstype=jffs2 rw
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 247144k/247144k available, 277144k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.000000]       .text : 0x80008000 - 0x806584f8   (6466 kB)
[    0.000000]       .init : 0x80659000 - 0x80687740   ( 186 kB)
[    0.000000]       .data : 0x80688000 - 0x806c8e60   ( 260 kB)
[    0.000000]        .bss : 0x806c8e60 - 0x806e3224   ( 105 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU debugfs-based tracing is enabled.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:350
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] Cortex A9 frequency at 600 MHz
[    0.000000] Initializing Cortex A9 Global Timer at Vir:0xFEA00200, using, at                                                                                                      Freq:300 MHz
[    0.000000] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 14316                                                                                                     ms
[    0.000000] smp_twd: clock not found -2
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.249863] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    0.292752] pid_max: default: 32768 minimum: 301
[    0.297555] Mount-cache hash table entries: 512
[    0.303979] CPU: Testing write buffer coherency: ok
[    0.309071] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.314697] Setting up static identity map for 0x803c47a0 - 0x803c47f8
[    0.321224] L310 cache controller enabled
[    0.325144] l2x0: 8 ways, CACHE_ID 0x410004c7, AUX_CTRL 0x32421001, Cache siz                                                                                                     e: 131072 B
[    0.333771] Brought up 1 CPUs
[    0.336653] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[    0.342974] CPU: All CPU(s) started in SVC mode.
[    0.348241] devtmpfs: initialized
[    0.356601] NET: Registered protocol family 16
[    0.361716] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.475090] GMAC0: active interface is 1
[    0.479081] ChipID=0x1000 ChipRevID=0x100
[    0.483178] nx_dmac: Registered with 8 channels
[    0.510220] bio: create slab <bio-0> at 0
[    0.515414] GPIO: base febab000 (phys e06ab000)
[    0.520005] GPIO: base feb69000 (phys e0669000)
[    0.526384] SCSI subsystem initialized
[    0.531504] usbcore: registered new interface driver usbfs
[    0.537081] usbcore: registered new interface driver hub
[    0.542743] usbcore: registered new device driver usb
[    0.548175] pps_core: LinuxPPS API ver. 1 registered
[    0.553101] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giome                                                                                                     tti <giometti@linux.it>
[    0.562385] PTP clock support registered
[    0.567952] cfg80211: Calling CRDA to update world regulatory domain
[    0.575759] Switching to clocksource arm_global_timer
[    0.599661] NET: Registered protocol family 2
[    0.604972] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.612059] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.618469] TCP: Hash tables configured (established 4096 bind 4096)
[    0.624815] TCP: reno registered
[    0.627954] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.633802] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.640287] NET: Registered protocol family 1
[    0.645031] RPC: Registered named UNIX socket transport module.
[    0.650873] RPC: Registered udp transport module.
[    0.655507] RPC: Registered tcp transport module.
[    0.660180] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.666735] PM: STB Platform power mgmt initialization.
[    0.797799] NFS: Registering the id_resolver key type
[    0.802863] Key type id_resolver registered
[    0.806942] Key type id_legacy registered
[    0.810970] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.817333] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.825287] msgmni has been set to 482
[    0.830388] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2                                                                                                     52)
[    0.837679] io scheduler noop registered
[    0.841625] io scheduler deadline registered
[    0.846480] io scheduler cfq registered (default)
[    0.851842] e06b2000.serial: ttyS0 at MMIO 0xe06b2000 (irq = 47) is a uart-ip                                                                                                     3106
[    0.866249] loop: module loaded
[    0.870454] ahci-stb e0638000.sata: unable to find phy
[    0.875503] SATA: Enable mpll_ss_en (rd_val=0x571185, wr_val=0x5711a5)
[    0.882039] SATA: Enable rx_term_en0 (rd_val=0x277, wr_val=0x277)
[    0.888052] ahci-stb e0638000.sata: SSS flag set, parallel bus scan disabled
[    0.895088] ahci-stb e0638000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x                                                                                                     1 impl platform mode
[    0.903874] ahci-stb e0638000.sata: flags: ncq sntf stag pm led clo only pmp                                                                                                      pio slum part ccc apst
[    0.913332] ata4294967295: SATA PHY offline
[    0.918344] scsi0 : ahci_platform
[    0.922494] ata1: SATA max UDMA/133 mmio [mem 0xe0638000-0xe0638fff] port 0x1                                                                                                     00 irq 39
[    0.932053] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 5                                                                                                     12MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
[    0.944476] Bad block table found at page 262080, version 0x01
[    0.951044] Bad block table found at page 262016, version 0x01
[    0.957246] nand_read_bbt: bad block at 0x00001cf60000
[    0.962304] nand_read_bbt: bad block at 0x00001cfa0000
[    0.967432] 3 cmdlinepart partitions found on MTD device e0631000.flash_nand
[    0.974389] Creating 3 MTD partitions on "e0631000.flash_nand":
[    0.980262] 0x000000000000-0x000010000000 : "root0"
[    0.986772] 0x000010000000-0x000012000000 : "var"
[    0.992856] 0x000012000000-0x000020000000 : "root1"
[    1.001170] JEDEC ID = 0x1c3016 , Extended Device ID = 0x1c30
[    1.006912] nx_sfc e0632000.flash_sfc: en25q32 (4096 Kbytes)
[    1.012568] 5 cmdlinepart partitions found on MTD device e0632000.flash_sfc
[    1.019425] Creating 5 MTD partitions on "e0632000.flash_sfc":
[    1.025242] 0x000000000000-0x000000040000 : "uldr"
[    1.031596] 0x000000040000-0x0000000c0000 : "u-boot"
[    1.037898] 0x0000000c0000-0x0000000e0000 : "env"
[    1.044025] 0x0000000e0000-0x000000100000 : "spare"
[    1.050476] 0x000000100000-0x000000400000 : "kernel"
[    1.057173] tun: Universal TUN/TAP device driver, 1.6
[    1.062191] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.068898]  DWMAC1000
[    1.071203] stmmac - user ID: 0x36, Synopsys ID: 0x36
[    1.076179]  Ring mode enabled
[    1.079204]  DMA HW capability register supported
[    1.083713]  Enhanced/Alternate descriptors
[    1.088016]  Enabled extended descriptors
[    1.092001]  RX Checksum Offload Engine supported (type 2)
[    1.097434]  TX Checksum insertion supported
[    1.101674]  Wake-Up On Lan supported
[    1.105342]  Enable RX Mitigation via HW Watchdog Timer
[    1.125383] libphy: stmmac: probed
[    1.128702] eth0: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) active
[    1.135080] eth0: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
[    1.140748] eth0: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
[    1.146419] eth0: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
[    1.152150] eth0: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
[    1.157824] eth0: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
[    1.163557] eth0: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
[    1.169228] eth0: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
[    1.174955] eth0: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
[    1.180659] eth0: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
[    1.186336] eth0: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
[    1.192146] eth0: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
[    1.197913] eth0: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
[    1.203729] eth0: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
[    1.209490] eth0: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
[    1.215302] eth0: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
[    1.221092] eth0: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
[    1.226857] eth0: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
[    1.232668] eth0: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
[    1.238434] eth0: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
[    1.244246] eth0: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
[    1.250011] eth0: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
[    1.255826] eth0: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
[    1.261609] eth0: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
[    1.267378] eth0: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
[    1.273192] eth0: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
[    1.278955] eth0: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
[    1.284768] eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
[    1.290554] eth0: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
[    1.296322] eth0: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
[    1.302134] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
[    1.307900] eth0: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
[    1.314193] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.320640] ehci-platform: EHCI generic platform driver
[    1.325896] ehci-platform e066c000.usb: EHCI Host Controller
[    1.331498] ehci-platform e066c000.usb: new USB bus registered, assigned bus                                                                                                      number 1
[    1.339338] ehci-platform e066c000.usb: irq 93, io mem 0xe066c000
[    1.360083] ehci-platform e066c000.usb: USB 2.0 started, EHCI 1.00
[    1.366234] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.372943] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=                                                                                                     1
[    1.380100] usb usb1: Product: EHCI Host Controller
[    1.384918] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.390381] usb usb1: SerialNumber: e066c000.usb
[    1.395808] hub 1-0:1.0: USB hub found
[    1.399486] hub 1-0:1.0: 1 port detected
[    1.403658] ehci-platform e066d000.usb: EHCI Host Controller
[    1.409232] ehci-platform e066d000.usb: new USB bus registered, assigned bus                                                                                                      number 2
[    1.417146] ehci-platform e066d000.usb: irq 94, io mem 0xe066d000
[    1.423200] ata1: SATA PHY offline
[    1.426523] ata1: SATA link down (SStatus 0 SControl 300)
[    1.440080] ehci-platform e066d000.usb: USB 2.0 started, EHCI 1.00
[    1.446230] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.452941] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=                                                                                                     1
[    1.460095] usb usb2: Product: EHCI Host Controller
[    1.464916] usb usb2: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.470370] usb usb2: SerialNumber: e066d000.usb
[    1.475756] hub 2-0:1.0: USB hub found
[    1.479429] hub 2-0:1.0: 1 port detected
[    1.484043] usbcore: registered new interface driver usb-storage
[    1.490441] usbcore: registered new interface driver usbserial
[    1.497753] usbcore: registered new interface driver usbhid
[    1.503295] usbhid: USB HID core driver
[    1.507290] TCP: cubic registered
[    1.510528] NET: Registered protocol family 17
[    1.515336] Key type dns_resolver registered
[    1.519614] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9                                                                                                      rev 3
[    1.527148] ThumbEE CPU extension supported.
[    1.532441] ### dt-test ### No testcase data in device tree; not running test                                                                                                     s
[    1.730082] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.881971] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    1.888587] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.895680] usb 1-1: Product: USB2.0 Hub
[    1.900869] hub 1-1:1.0: USB hub found
[    1.904970] hub 1-1:1.0: 4 ports detected
[    2.600059] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    2.752267] usb 2-1: New USB device found, idVendor=174c, idProduct=5136
[    2.758877] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    2.765966] usb 2-1: Product: AS2105
[    2.769487] usb 2-1: Manufacturer: ASMedia
[    2.773556] usb 2-1: SerialNumber: 00000000000000000000
[    2.779908] usb-storage 2-1:1.0: USB Mass Storage device detected
[    2.786188] scsi1 : usb-storage 2-1:1.0
[    3.791011] scsi 1:0:0:0: Direct-Access     ASMT     2105             0    PQ                                                                                                     : 0 ANSI: 6
[    3.800833] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    4.638587] sd 1:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/93                                                                                                     1 GiB)
[    4.646925] sd 1:0:0:0: [sda] Write Protect is off
[    4.652587] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, does                                                                                                     n't support DPO or FUA
[    4.687095]  sda: sda1
[    4.692953] sd 1:0:0:0: [sda] Attached SCSI disk
[    6.962741] VFS: Mounted root (jffs2 filesystem) on device 31:0.
[    6.969994] devtmpfs: mounted
[    6.973185] Freeing unused kernel memory: 184K (80659000 - 80687000)
init started: BusyBox v1.30.1 (2019-06-22 15:09:50 CEST)
[    7.850015] NET: Registered protocol family 10
try to mount /dev/mtdblock1 to /var
[    8.315047] jffs2: Empty flash at 0x0120aab4 ends at 0x0120b000
starting /etc/init.d/S02loadmodules ...
Sat Jan  1 00:00:00 CET 2000
Creating device node for cs_display
Running insmod now .......
Driver modules loaded, please start the app now...
Creating device node for KAL
Creating device node for notifyq
Creating device node for platform
Creating device node for content
Creating device node for standby
Creating device node for video
Creating device node for audio
Creating device node for pvr
Creating device node for ci
Creating device node for cs_control
Creating device node for cs_ir
Creating device node for fb
starting /etc/init.d/S04mdev ...
[logoview] done with Timeout...
error connect socket /tmp/neutrino.sock: No such file or directory
starting /etc/init.d/S05mount ...
starting /etc/init.d/S50hostname ...
starting /etc/init.d/S51networking ...
Configuring network interfaces... Starting wlan0
Failed to connect to wpa_supplicant - wpa_ctrl_open: Success
Could not read interface wlan0 flags: No such device
Failed to initialize driver interface
done.
starting /etc/init.d/S52syslogd ...
Jan  1 00:00:14 CST-25BAB7 syslog.info syslogd started: BusyBox v1.30.1
starting /etc/init.d/S60autofs ...
 1 Jan 00:00:14 ntpdate[1137]: ntpdate 4.2.8p6@1.3265-o (1)
starting
starting /etc/init.d/S80dvdreadfs ...
starting /etc/init.d/S90inetd ...
starting /etc/init.d/S96nfsd ...
starting /var/etc/init.d/S9T_tuxcald ...
starting /var/etc/init.d/S9T_tuxmaild ...
Jan  1 00:00:15 CST-25BAB7 daemon.info : starting pid 1173, tty '': '/etc/init.d                                                                                                     /start_neutrino'

Please press Enter to activate this console. /var/plugins/operations camd_init
/var/plugins/operations cardserver_start
starte doscam
Sat Jan  1 00:00:16 CET 2000
/var/plugins/operations camd_start
/var/plugins/operations rezap
30 Dec 14:54:44 ntpdate[1137]: step time server 130.133.1.10 offset 631032867.38                                                                                                     1664 sec
/var/plugins/operations: line 262: 6: not found
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend3: No such file or directory
MON: The POD Monitor task has started. Version = 01, Release = 00, Subrelease =                                                                                                      01, PID: 1213
MON: Initializing
slot->inbound_queue : 7608a070
slot->outbound_queue: 76089f18
xport_command_queue: 76089d00
MON: Start resource providers...
MON: Starting 9 resource(s).
XPORT: POD Transport task started. PID: 1213
RM: Resource Manager thread started. PID: 1213
LINK: POD link task started with arg=0x00000000, PID: 1213
ciappReportModuleStatus: status 9, gCardStatus: 0
MON starting 9 resources finished
MON after BR_POD_mon_start_rps
CA resource provider started with arg=0x00000000, PID: 1213
SYSTIME resource start, PID: 1213
CP resource start, PID: 1213
APPMMI thread starts, PID: 1213
UPGRADE thread is started, PID: 1213
HOSTLANG_CNTY thread is started, PID: 1213
HOSTCTRL thread is started, PID: 1213
MMI thread is started, PID: 1213
APPINFO thread starts, PID: 1213
CP thread get delay time 0(s)
XPORT: transport connection #1 set to Idle
comming in  add resource provider, rid=10041
POD timer thread PID: 1213
PHYS-CI+: cs_ci_init_controller called
LINK: hard reset complete.
CP: Start of initialization...
comming in  add resource provider, rid=200041
HOSTCTRL RP: resource provider is added
HOSTCTRL RP: HOSTCTRL resource provider main loop processing started.
comming in  add resource provider, rid=30041
comming in  add resource provider, rid=20043
comming in  add resource provider, rid=8e1001
UPGRADE RP: resource provider is added
UPGRADE RP: UPGRADE resource provider main loop processing started.
LINK: slot #0 state = BR_POD_SLOT_NOT_INIT
RM before wait for db ready, pid: 1213
APPINFO RP: resource provider is added, resource ID :0x20043
CA RP: Resource Provider main loop processing started.
CP nvram: Root certificate file is for production
comming in  add resource provider, rid=410041
APPMMI RP: resource provider is added
APPMMI RP: APPMMI resource provider main loop processing started.
APPINFO RP: APPINFO resource provider main loop processing started.
comming in  add resource provider, rid=240041
SYSTIME RP: System Time main loop processing started.
comming in  add resource provider, rid=8d1001
HOSTLANG_CNTY RP: resource provider is added
HOSTLANG_CNTY RP: HOSTLANG_CNTY resource provider main loop processing started.
dump mbuf....
RM after wait for db ready, pid: 1213
MON after wait event
MON: Wait for all required resource providers to sign on....
RM: Resource Manager message processing started.
LINK: slot #0 state = BR_POD_SLOT_CARD_NOT_PRESENT
RM: recvd LINK_STATUS tag(0x42), len=8
RM: No host-pod interface
RM: close all connections on slot 0
comming in  add resource provider, rid=400041
MMI RP: resource provider is added
MMI RP: MMI resource provider main loop processing started.
LINK: after bypass card
dump mbuf....
ciappReportModuleStatus: status 0, gCardStatus: 0
dump mbuf....
no CICAM brand id extension.
comming in  add resource provider, rid=8c1001
RM: recvd RM_RESOURCES_CHANGED tag(0x43), len=8
CP RP: resource provider is added
CP: Resource Provider main loop processing started.
2019-12-30 14:54:54.218 [sectionsd] start
2019-12-30 14:54:54.282 [sectionsd] starting
2019-12-30 14:54:54.385 [sectionsd] timeThread::run:: starting, pid 1213 (167210                                                                                                     3088)
2019-12-30 14:54:54.391 [sectionsd] eitThread::run:: starting, pid 1213 (1670005                                                                                                     936)
2019-12-30 14:54:54.398 2019-12-30 14:54:54.407 [sectionsd] cnThread::run:: star                                                                                                     ting, pid 1213 (1667908784)
[sectionsd] freeSatThread::run:: starting, pid 1213 (1665811632)
2019-12-30 14:54:54.517 [sectionsd] timeThread: get DVB time ch 0x000000000000 (                                                                                                     isOpen 1)
[ConfigFile] Unable to open file /var/tuxbox/config/bookmarks for reading.
2019-12-30 14:54:55.895 [sectionsd] commandserviceStopped
2019-12-30 14:54:55.902 [sectionsd] cnThread: stop eit update filter (not active                                                                                                     )
2019-12-30 14:54:55.911 [sectionsd] commandserviceStopped done
2019-12-30 14:54:55.942 [sectionsd] commandserviceChanged: Service change to 221                                                                                                     42710f001c764 demux #0
2019-12-30 14:54:55.947 [sectionsd] timeThread: get DVB time ch 0x2710f001c764 r                                                                                                     c: -1 neutrino_sets_time 0
2019-12-30 14:54:56.160 [sectionsd] timeThread: Time set FAILED (enabled: ntp 0                                                                                                      dvb 1)
sh: you need to specify whom to kill
2019-12-30 14:54:56.862 [sectionsd] commandserviceChanged: Service change to 221                                                                                                     42710f001c764 demux #0
2019-12-30 14:54:57.186 [sectionsd] timeThread: get DVB time ch 0x2710f001c764 (                                                                                                     isOpen 1)
2019-12-30 14:54:57.485 [sectionsd] timeThread: get DVB time ch 0x2710f001c764 r                                                                                                     c: 8 neutrino_sets_time 0
2019-12-30 14:54:57.495 [sectionsd] SIsectionTIME::parse: TDT time: Mon Dec 30 1                                                                                                     4:54:28 2019
2019-12-30 14:54:57.498 [sectionsd] timeThread: timediff -29498799, current: 30.                                                                                                     12.2019 14:54:57, dvb: Mon Dec 30 14:54:28 2019

2019-12-30 14:54:28.000 [sectionsd] eitThread::run:: time set: Mon Dec 30 14:54:                                                                                                     28 2019

2019-12-30 14:54:28.009 2019-12-30 14:54:28.009 [sectionsd] cnThread::run:: time                                                                                                      set: Mon Dec 30 14:54:28 2019

[sectionsd] freeSatThread::run:: time set: Mon Dec 30 14:54:28 2019

2019-12-30 14:54:28.019 [sectionsd] timeThread: Time set via DVB (TDT), going to                                                                                                      sleep for 5 seconds.
2019-12-30 14:54:28.109 [sectionsd] addEvent: ch 2710f001c764 running 4 (curr) g                                                                                                     ot_CN 0
2019-12-30 14:54:28.608 [sectionsd] addEvent: ch 2710f001c764 running 1 (next) g                                                                                                     ot_CN 1
2019-12-30 14:54:30.058 [sectionsd] cnThread: eit update filter, ch 0x2710f001c7                                                                                                     64, current ver 0x08  got events 3 (not active)
 --- > rezapping
2019-12-30 14:54:32.539 [sectionsd] commandserviceChanged: Service change to 221                                                                                                     42710f001c764 demux #0
2019-12-30 14:54:33.074 [sectionsd] timeThread: get DVB time ch 0x2710f001c764 (                                                                                                     isOpen 1)
2019-12-30 14:54:35.477 [sectionsd] timeThread: get DVB time ch 0x2710f001c764 r                                                                                                     c: 29 neutrino_sets_time 0
2019-12-30 14:54:35.485 [sectionsd] SIsectionTIME::parse: TOT time: Mon Dec 30 1                                                                                                     4:54:35 2019
2019-12-30 14:54:35.494 [sectionsd] timeThread: timediff -494060, current: 30.12                                                                                                     .2019 14:54:35, dvb: Mon Dec 30 14:54:35 2019

2019-12-30 14:54:35.505 [sectionsd] difference is < 120s, using adjtime(0, -4940                                                                                                     60). oldd(0, 0)
2019-12-30 14:54:35.511 [sectionsd] timeThread: Time set via DVB (TOT), going to                                                                                                      sleep for 1800 seconds.

 

 

bearbeitet von Gandal
OK, den nächsten Betrag lösche ich einfach wenn keine Spoiler-Tags verwendet werden.

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen

Ja die Box läuft hoch. Aber nur über Scart kann ich den Stratbildschirm und später auch das Fernsehbild sehen. Beim Booten wird erst das Coolstream Logo aus dem Boot (meine Vermutung) angezeigt! Selbst dann das Startbild des Image wird nicht gezeigt und auf dem Bildschirm tanzen grüne Streifen senkrecht und wagerecht auf schwarzen Grund.

Sobald dann auch das normale Fernsehbild erscheint kommt dieses auch auf den Fernseher!

Wie geschrieben ist bei der Nutzung nur HDMI alles schwarz bis zum Fernseh(TON). Da ja kein Bild erscheint.

Damit bin ich bei Euch, dass dies den Chip zerstört hat, der das HDMI Signal rausgibt.

 

Du hast jetzt das PDF zum Chip gesandt. Auf der Platine glaube ich diesen neben dem Kühler gefunden zu haben. Die Hoffnung! Ist gesockelt war natürlich die Ente in 2019!

Kann man so eine Mittenplatine nachkaufen und oder Reparieren?

Oder wird die  Coolie jetzt zum Elektroschrott?

 

 

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen

Hi,

also das Bootlog hört zu früh auf, da müsste noch ne Menge mehr kommen.

 

Und hast du eigentlich schon den Standardtrick bei HDMI-Problemen versucht:

Beide Geräte auschalten, beide Stecker ziehen und mind 2 Minuten warten. Dann zuerst den TV anmachen und komplett starten lassen, danach erst die Box einschalten und dabei die Daumen drücken. ;)

 

Ciao,

DdD.

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen

Das müsst Ihr mir jetzt mal erklären! Im Vorfeld hätte ich mindestens 50€ gewettet, dass der "Standardtrick" soviel hilft wie streicheln und oder beten!

 

Erst einmal vielen Dank! JA ES LÄUFT WIEDER AUF HDMI OHNE PROBLEME!

 

Aber bitte mal erklären was passiert ist und wie es behoben wurde, dass glaubt mir sonst niemand.

 

Vielen Dank Euch für die Hilfe!

 

 

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen
vor 20 Minuten schrieb skyline666:

Du hast jetzt das PDF zum Chip gesandt. Auf der Platine glaube ich diesen neben dem Kühler gefunden zu haben. Die Hoffnung! Ist gesockelt war natürlich die Ente in 2019!

Kann man so eine Mittenplatine nachkaufen und oder Reparieren?

 

Reparieren ist möglich, entweder selbder machen oder jemanden suchen der das erledigt.

Zu kaufen wird es die Platine kaum mehr geben, vielleicht aus einer defekten Box falls so was irgendwo angeboten wird.

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen
vor 3 Minuten schrieb skyline666:

Aber bitte mal erklären was passiert ist und wie es behoben wurde, dass glaubt mir sonst niemand.

 

 

Das Zauberwort heisst HDMI-CEC

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen

Hi,

ohne es genau zu wissen, erkläre ich es mir so, dass der TV sich da iwas merkt, bzw durch das Anstöpseln des anderen Gerätes was verstellt wurde.

Durch Stromlos machen vergisst er das alles wieder und durch das erst spätere Einschalten der Box werden die Sachen wieder neu zw den beiden Geräten ausgehandelt...

 

Ciao,

DdD.

Diesen Beitrag teilen


Link zum Beitrag
Auf anderen Seiten teilen

  • Wer ist Online   0 Benutzer

    Keine registrierten Benutzer online.

×
×
  • Neu erstellen...