frankl Geschrieben 1. Oktober 2011 Melden Share Geschrieben 1. Oktober 2011 Hi, bei meiner Sagem DBox2 SAT (Keywelt Jan2011_V2) tritt folgendes Problem auf. Wenn ich die Box, aus dem Deep-Standby, wieder anschalten will, bleibt sie während des Bootvorganges hängen. Dann hilft nur noch ein Hardwarereset. Log vom Bootvorgang mit Hänger ÿdebug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: LCD init error -1 debug: WATCHDOG RESET debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS debug: Got Block #0008debug: Got Block #0012debug: Got Block #0016debug: Got Block #0020debug: Got Block #0024debug: Got Block #0028debug: Got Block #0032debug: Got Block #0036debug: Got Block #0040debug: Got Block #0044 will verify ELF image, start= 0x800000, size= 173832 verify sig: 262 Branching to 0x40000 U-Boot 2010.03 (Tuxbox) (Feb 11 2011 - 14:00:53) CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Sagem, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB Scanning JFFS2 FS: . | / - \ . | / - . \ done. env: found console with value ttyS0 env: found lcd_inverse with value 0 env: found lcd_contrast with value 15 FB: ready In: serial Out: serial Err: serial Net: SCC ETHERNET LCD: ready Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 1 0 ............................................................... done Un-Protected 63 sectors ### FS (squashfs) loading 'vmlinuz' to 0x200000 ### FS load complete: 671071 bytes loaded to 0x200000 ## Booting kernel from Legacy Image at 00200000 ... Image Name: Linux-2.4.37.11-dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 671007 Bytes = 655.3 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.37.11-dbox2 (image@server) (gcc version 3.4.6) #8 Fr 11. Feb 14:01:27 CET 2011 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex= Decrementer Frequency = 247500000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x2000) Console: colour dummy device 80x25 Calibrating delay loop... 65.74 BogoMIPS Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. squashfs: version 3.0 (2006/03/15) Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured half-duplex mode enabled eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:32:e0:ed loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00040000 : "FLFS (U-Boot)" 0x00040000-0x005e0000 : "root (squashfs+lzma)" 0x005e0000-0x00800000 : "var (jffs2)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.17.3 (2011-02-11 14:04:29 CET) starting pid 8, tty '': '/etc/init.d/rcS' mount: using /etc/fstab ##### Image-Version: Keywelt_Jan2011_V2.00 ##### Fri Feb 11 14:15:00 UTC 2011 event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ tuxbox: no IDE-Interface detected Detected STB: Vendor: Sagem Model: D-BOX2 [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 $Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $ $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ avia_av: $Id: avia_av_core.c,v 1.102 2010/05/25 19:58:20 dbt Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av: AVIA 600L found. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $ SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35cb9b, size 25bf insmod: not an ELF file SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 insmod: not an ELF file lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 insmod: not an ELF file SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 insmod: not an ELF file Node header CRC failed at 0012c6c4. But it must have been OK earlier. Node was: { c1ae, e1ae, c1aec1ae, c1aec1ae } Node totlen on flash (0x00000000) != totlen from node ref (0x00000030) Node header CRC failed at 0012c620. But it must have been OK earlier. Node was: { c1ae, e1ae, c1aec1ae, c1aec1ae } Node totlen on flash (0x00000000) != totlen from node ref (0x00000034) Node header CRC failed at 0012c390. But it must have been OK earlier. Node was: { c1ae, e1ae, c1aec1ae, c1aec1ae } Node totlen on flash (0x00000000) != totlen from node ref (0x00000044) insmod: unresolved symbol avia_gNode header CRC failed at 0010ca18. But it must have been OK earlier. Node was: { c1eb, e1eb, c1ebc1eb, c1ffc1ff } Node totlen on flash (0x00000000) != totlen from node ref (0x00000038) Node header CRC failed at 0010c6f4. But it must have been OK earlier. Node was: { c1eb, e1eb, c1ebc1eb, c1ffc1ff } Node totlen on flash (0x00000000) != totlen from node ref (0x00000030) jffs2_do_read_inode(): No data nodes found for ino #149 t_pig_show Node header CRC failed at 001c7464. But it must have been OK earlier. Node was: { c1ba, e1ba, c1bac1ba, c1ffc1ff } Node totlen on flash (0xffffffff) != totlen from node ref (0x00000044) Node header CRC failed at 00043c60. But it must have been OK earlier. Node was: { c1eb, e1eb, c1ebc1eb, c1ffc1ff } Node totlen on flash (0x00010001) != totlen from node ref (0x00000034) jffs2_do_read_inode(): No data nodes found for ino #60 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [48de3] SQUASHFS error: Unable to read page, block 48de3, size 41fc fopen(BMP_FILE): Input/output errorSQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [48de3] SQUASHFS error: Unable to read page, block 48de3, size 41fc SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [48de3] SQUASHFS error: Unable to read page, block 48de3, size 41fc SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [48de3] SQUASHFS error: Unable to read page, block 48de3, size 41fc ifup: can't open '/etc/network/interfaces': Input/output error Node header CRC failed at 001c6f3c. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0x00000000) != totlen from node ref (0x00000130) jffs2_do_read_inode(): No data nodes found for ino #55 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34f4b2] SQUASHFS error: Unable to read page, block 34f4b2, size 498b SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34f4b2] SQUASHFS error: Unable to read page, block 34f4b2, size 498b SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34f4b2] SQUASHFS error: Unable to read page, block 34f4b2, size 498b insmod: not an ELF file ves1x93: Detected ves1993 DVB: registering frontend 0:0 (VES1993)... SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35f15a] SQUASHFS error: Unable to read page, block 35f15a, size 49a9 insmod: not an ELF file SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [363b03] SQUASHFS error: Unable to read page, block 363b03, size 3163 insmod: not an ELF file insmod: unresolved symbol avia_gt_napi_dvr_send insmod: unresolved symbol avia_gt_set_playback_mode Node header CRC failed at 00000f68. But it must have been OK earlier. Node was: { c1f7, e1f7, c1f7c1f7, c1f7c1f7 } Node totlen on flash (0xc1f4c1f4) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #337 insmod: warning: kernel-module version mismatch multicam was compiled for kernel version 2.4.37-dbox2 while this kernel is version 2.4.37.11-dbox2 DBox2 Multicam Driver v1.01 skars & doz21 Node header CRC failed at 001c6310. But it must have been OK earlier. Node was: { c000, e000, c000c000, c03fc03f } Node totlen on flash (0x00000000) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #34 Node header CRC failed at 001c6450. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0xc1acc1ac) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #36 Node header CRC failed at 000d2e54. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000084) jffs2_do_read_inode(): No data nodes found for ino #57 /var/etc/init.d/rcS: line 296: can't create /etc/issue.net: Input/output error Node header CRC failed at 0012c478. But it must have been OK earlier. Node was: { c1cc, e1cc, c1ccc1cc, c1ccc1cc } Node totlen on flash (0xc1acc1ac) != totlen from node ref (0x00000044) Node header CRC failed at 00086dfc. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00150015) != totlen from node ref (0x00000034) Node header CRC failed at 00086d68. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00150015) != totlen from node ref (0x00000034) Node header CRC failed at 00086cd4. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00150015) != totlen from node ref (0x00000034) Node header CRC failed at 00086c40. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00150015) != totlen from node ref (0x00000034) Node header CRC failed at 00086b9c. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 003f003f } Node totlen on flash (0x00150015) != totlen from node ref (0x0000003c) Node header CRC failed at 00086b00. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00010001 } Node totlen on flash (0x00150015) != totlen from node ref (0x00000038) Node header CRC failed at 00086a6c. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00170017 } Node totlen on flash (0xc1acc1ac) != totlen from node ref (0x00000034) Node header CRC failed at 000869d8. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00150015) != totlen from node ref (0x00000034) Node header CRC failed at 00086944. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00150015) != totlen from node ref (0x00000034) jffs2_do_read_inode(): No data nodes found for ino #151 mkdir: can't create directory '/var/tuxbox/fonts': File exists /var/etc/init.d/rcS: cd: line 326: can't cd to /var/tuxbox/fonts/ SR.4 or SR.5 bits set in buffer write (status 70). Clearing. Write of 94 bytes at 0x000d4154 failed. returned -30, retlen 0 Not marking the space at 0x000d4154 as dirty because the flash driver returned retlen zero Write of 94 bytes at 0x000d4154 failed. returned -30, retlen 0 Not marking the space at 0x000d4154 as dirty because the flash driver returned retlen zero ln: tuxtxt.otb: Read-only file system SR.4 or SR.5 bits set in buffer write (status ff). Clearing. SR.4 or SR.5 bits set in buffer write (status c015). Clearing. Write of 94 bytes at 0x000d4154 failed. returned -30, retlen 12 Write of 94 bytes at 0x000d41b4 failed. returned -30, retlen 0 Not marking the space at 0x000d41b4 as dirty because the flash driver returned retlen zero ln: tuxtxt.ttf: Read-only file system SR.4 or SR.5 bits set in buffer write (status ff). Clearing. Write of 96 bytes at 0x000d41b4 failed. returned -30, retlen 0 Not marking the space at 0x000d41b4 as dirty because the flash driver returned retlen zero Write of 96 bytes at 0x000d41b4 failed. returned -30, retlen 0 Not marking the space at 0x000d41b4 as dirty because the flash driver returned retlen zero ln: pakenham.ttf: Read-only file system SR.4 or SR.5 bits set in buffer write (status ff). Clearing. SR.4 or SR.5 bits set in buffer write (status c015). Clearing. Write of 96 bytes at 0x000d41b4 failed. returned -30, retlen 12 Write of 96 bytes at 0x000d4214 failed. returned -30, retlen 0 Not marking the space at 0x000d4214 as dirty because the flash driver returned retlen zero ln: bluehigh.ttf: Read-only file system Node CRC ffffffff != calculated CRC f70f6a3e for node at 00041fd0 Node CRC ffffffff != calculated CRC 91958955 for node at 00041fd0 SR.4 or SR.5 bits set in buffer write (status 70). Clearing. SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x000d4214 failed. returned -30, retlen 12 Write of 96 bytes at 0x000d4274 failed. returned -30, retlen 0 Not marking the space at 0x000d4274 as dirty because the flash driver returned retlen zero ln: blue: Read-only file system starting pid 140, tty '': '/etc/init.d/start' Node header CRC failed at 000422f8. But it must have been OK earlier. Node was: { 01a8, 21a8, 01a801a8, 01ab01ab } Node totlen on flash (0x00040004) != totlen from node ref (0x000001b4) jffs2_do_read_inode(): No data nodes found for ino #74 can't run '/etc/init.d/start': Input/output error Auszug aus dem Log: "SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 35739e, size 57fd" Log vom Bootvorgang der funktioniert - nach Reset ˜debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS debug: Got Block #0008debug: Got Block #0012debug: Got Block #0016debug: Got Block #0020debug: Got Block #0024debug: Got Block #0028debug: Got Block #0032debug: Got Block #0036debug: Got Block #0040debug: Got Block #0044 will verify ELF image, start= 0x800000, size= 173832 verify sig: 262 Branching to 0x40000 U-Boot 2010.03 (Tuxbox) (Feb 11 2011 - 14:00:53) CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Sagem, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB Scanning JFFS2 FS: . | / - \ . | / - . \ done. env: found console with value ttyS0 env: found lcd_inverse with value 0 env: found lcd_contrast with value 15 FB: ready In: serial Out: serial Err: serial Net: SCC ETHERNET LCD: ready Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 1 0 ............................................................... done Un-Protected 63 sectors ### FS (squashfs) loading 'vmlinuz' to 0x200000 ### FS load complete: 671071 bytes loaded to 0x200000 ## Booting kernel from Legacy Image at 00200000 ... Image Name: Linux-2.4.37.11-dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 671007 Bytes = 655.3 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.37.11-dbox2 (image@server) (gcc version 3.4.6) #8 Fr 11. Feb 14:01:27 CET 2011 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex= Decrementer Frequency = 247500000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x2000) Console: colour dummy device 80x25 Calibrating delay loop... 65.74 BogoMIPS Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. squashfs: version 3.0 (2006/03/15) Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured half-duplex mode enabled eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:32:e0:ed loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00040000 : "FLFS (U-Boot)" 0x00040000-0x005e0000 : "root (squashfs+lzma)" 0x005e0000-0x00800000 : "var (jffs2)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.17.3 (2011-02-11 14:04:29 CET) starting pid 8, tty '': '/etc/init.d/rcS' mount: using /etc/fstab ##### Image-Version: Keywelt_Jan2011_V2.00 ##### Fri Feb 11 14:15:00 UTC 2011 event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ tuxbox: no IDE-Interface detected Detected STB: Vendor: Sagem Model: D-BOX2 [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 $Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $ $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ avia_av: $Id: avia_av_core.c,v 1.102 2010/05/25 19:58:20 dbt Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av: AVIA 600L found. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $ avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $ avia_gt_core: autodetecting chip type... eNX avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $ avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $ avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $ avia_gt_ucode: loaded ucode v001A avia_gt_ucode: ucode section filters disabled. avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning... avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $ avia_gt_gv: set_input_size (width=720, height=576) avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $ avia_gt_pcm_set_rate(44100) avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $ avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $ avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $ avia_gt_core: Loaded AViA eNX/GTX driver avia_av_core: Starting avia_gt_wdt thread. avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $ avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) Console: switching to colour frame buffer device 82x32 avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $ avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $ avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $ avia_gt_pcm_set_rate(44100) avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $ ves1x93: Detected ves1993 DVB: registering frontend 0:0 (VES1993)... avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $ avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $ insmod: warning: kernel-module version mismatch avia_gt_proc was compiled for kernel version 2.4.37-dbox2 while this kernel is version 2.4.37.11-dbox2 avia_gt_proc: Using config file '/var/tuxbox/config/avia.conf'. avia_gt_proc: $Id: avia_gt_proc.c,v 0.92d 2003/06/18 19:00:00 bofh Exp $ avia_gt_proc: found - AVIA eNX insmod: warning: kernel-module version mismatch multicam was compiled for kernel version 2.4.37-dbox2 while this kernel is version 2.4.37.11-dbox2 DBox2 Multicam Driver v1.01 skars & doz21 starting pid 177, tty '': '/etc/init.d/start' Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.320 2011/01/22 12:17:57 seife Exp $ [sectionsd] FreeSat enabled [sectionsd] Caching max 3000 events [sectionsd] Caching 4 days [sectionsd] Caching 12 hours Extended Text [sectionsd] Events are old 120min after their end time /var/tuxbox/config/zapit/epgfilter.xml: No such file or directory /var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory /var/tuxbox/config/mybouquets.xml: No such file or directory [timerd] woke up from timer? false! /var/plugins/operations camd_init /var/plugins/operations cardserver_start $Id: zapit.cpp,v 1.440k 2009/09/18 20:30:00 rhabarber1848 & Worschter & SnowHead Exp $ [zapit] PMT update enabled [frontend] uncommitted_switch_mode 0 auto_fec 0 /share/tuxbox/satellites.xml: No such file or directory [getservices] satellites.xml starte oscam couldn't open logfile: /dev/tty (errno 6 No such device or address) [getservices] /var/tuxbox/config/zapit/myservices.xml found. /var/tuxbox/config/zapit/ubouquets.xml: No such file or directory /var/plugins/operations camd_start /tmp/currentservices.xml: No such file or directory [controld] Boxtype detected: (3, Sagem D-BOX2) [controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1 [CVideo::setVideoFormat] output format: 4:3(LB) /var/plugins/operations sect_renice neutrino: /lib/libpng12.so.0: no version information available (required by neutrino) neutrino: /lib/libpng12.so.0: no version information available (required by /lib/liblcddisplay.so.0) starting /bin/neutrino [neutrino] frameBuffer Instance created 812k video mem avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) [neutrino] enable flash [neutrino] Software update enabled [lcdd] time-skin not found -> using default... [lcdd] weekday-skin not found -> using default... [lcdd] date-skin not found -> using default... [lcdd] month-skin not found -> using default... [LCDFONT] initializing core... [LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular) [LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold) [LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold) [LCDFONT] Intializing font cache... [LCDFONT] FTC_Face_Requester (Fix14/Bold) [neutrino] SetupFonts filename: /share/fonts/micron.ttf fontname: Micron [rcinput] no file /var/tuxbox/config/rc.conf was found /dev/input/event1: No such file or directory [neutrino] menue setup [neutrino] init menus... [neutrino] GUI-Personalize instance created... [neutrino] found esound, adding personalized esound entry to mainmenue [network config] Instance created [neutrino] setRepeat: delay=150 period=125 use kernel-repeat: no [neutrino] registering as event client /share/tuxbox/satellites.xml: No such file or directory [scan-setup] received 0 sats busy /tmp/zapit.sock [CVideo::setVideoFormat] output format: 4:3(LB) [LCDFONT] FTC_Face_Requester (Fix15/Bold) [zapit] tuned frequency does not match request. difference: 214 [sectionsd] getUTC: read: Connection timed out PES, queue 0 normal. [neutrino] no file /var/tuxbox/config/init.end was found [neutrino] initialized everything [controld] VIDEO_EVENT_SIZE_CHANGED 720x576 (4:3 -> 16:9) [CVideo::setVideoFormat] output format: 16:9 /bin/nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/liblcddisplay.so.0) [yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0) [LCDFONT] initializing core... [LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular) [LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold) [LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular) [LCDFONT] Intializing font cache... [yhttpd] Webserver starting... 15:16:00.968 [timeThread] - 01.10.2011 08:05:58, tim: Sat Oct 1 08:05:58 2011 [neutrino] timeset event. difference is 20015397 s, stepping... 15:16:01.024 [timeThread] Time set via DVB, going to sleep for 1800 seconds. 08:05:58.980 dmxSDT: going to sleep... Warning: keyword 'enabled' in reader section not recognized [timerd] using config file /var/tuxbox/config/timerd.conf [timerd] using config file /var/tuxbox/config/timerd.conf 08:06:34.138 eit_set_update_filter, servicekey = 0x443000179f4, current version 255 LG frank Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 1. Oktober 2011 Melden Share Geschrieben 1. Oktober 2011 Könnte sein, dass der Flash-Chip dabei ist, aus Altersschwäche den Geist aufzugeben (initialisiert zu spät, das ist die Vorstufe von Ausfällen). Genau sagen lässt sich das aber so auch nicht, das kann nur eine Werkstatt rausfinden. Fakt ist, dass beim ersten Bootlog diverse Blockadressen aus dem Flash nicht gelesen werden können, was dann zwangsläufig zu Schrott beim Laden von Dateien führt und sich die Box dann irgendwann aufhängt, weil es nicht weitergeht. Du kannst mal versuchen, einen kompletten Flash-Erase auszuführen: - Box in Deep Standby befördern (oder Stecker ziehen, geht auch) - einschalten/einstecken und dabei sofort (!) die Pfeil-runter-Taste drücken und festhalten (!), mindestens 5 Sekunden, in der Originalanleitung zur BN-Software ist sogar von mindestens 12 Sekunden die Rede. - "Flash Erase" muss im Display erscheinen Das Prozedere ist etwas knifflig und braucht oftmals mehrere Anläufe, also nicht gleich verzweifeln, wenn statt des Flash Erase die Box zu starten beginnt. Box anschließend neu flashen. Hilft das nicht, ist wohl der Gang in die Werkstatt nötig - oder die Tonne für die Box. Hab jetzt keinen Überblick, was der Tausch des Flash ungefähr kostet, aber ich denke mal, mit um die 30 Euro wirst Du rechnen müssen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
frankl Geschrieben 2. Oktober 2011 Autor Melden Share Geschrieben 2. Oktober 2011 Hi, habs probiert. Leider kein Erfolg. also nicht gleich verzweifeln, wenn statt des Flash Erase die Box zu starten beginnt. Anstatt dass die Box neu startet bleibt die Box beim Booten hängen und im Display steht dann Dann hilft nur noch ein HardwareReset. LG frankl Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 2. Oktober 2011 Melden Share Geschrieben 2. Oktober 2011 Starte die Box mit gedrückt gehaltener Pfeil-Hoch-Taste und lass sie dort ein paar Minuten hängen, damit der Flash warm läuft. Dann resette die Box über Power und Pfeil-Hoch, drücke anschließend sofort (!) die Pfeil-Runter-Taste und halte sie gedrückt. Das sollte auch funktionieren, um den Flash-Erase in Gang zu bekommen, dem Bootloader ist das praktisch wurscht, ob die Box frisch an den Strom angesteckt, aus dem Deep Standby geweckt oder direkt resettet wird, der Flash-Erase wird vom Bootloader initialisiert. Wenn sich die Box dabei aber auch wieder laufend aufhängt, ist sie definitiv ein Fall für die Werkstatt oder den Schrottkübel - was ich fast vermute. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
frankl Geschrieben 2. Oktober 2011 Autor Melden Share Geschrieben 2. Oktober 2011 Hi, Starte die Box mit gedrückt gehaltener Pfeil-Hoch-Taste und lass sie dort ein paar Minuten hängen, damit der Flash warm läuft. hab ich gemacht. Hier das Log. debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled debug: &_text 0x10000, &_etext 0x26ec0, &_data 0x26ec0, &_edata 0x2a9bc debug: &_end 0x35944, &__stack 0x400000 debug: Memory tests (0x400000 -- 0x2000000) debug: NumberTest: debug: passed debug: MarchTest: debug: passed debug: PermTest: debug: passed Dann resette die Box über Power und Pfeil-Hoch, drücke anschließend sofort (!) die Pfeil-Runter-Taste und halte sie gedrückt. Box bleibt wieder an der gleichen Stelle hängen. Siehe Log. ˜debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled Wenn sich die Box dabei aber auch wieder laufend aufhängt, ist sie definitiv ein Fall für die Werkstatt oder den Schrottkübel - was ich fast vermute. Im normalen Betrieb hab ich noch nichts weiter feststellen können, also keinerlei offensichtliche Probleme. Beim "Neustarten" der Box oder nach einem Hardwarereset bootet die Box ohne Probleme. Auch wenn ich die Box in den DeepStandby versetze und ein paar Minuten später die Box wieder starte ist alles ok. Das Problem taucht erst auf wenn die Box länger im DeepStandby war. Ich hatte vor einigen Tagen das Lcd-Display der Box getauscht, daran wird es ja wohl nicht liegen? LG frankl Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 2. Oktober 2011 Melden Share Geschrieben 2. Oktober 2011 debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled debug: &_text 0x10000, &_etext 0x26ec0, &_data 0x26ec0, &_edata 0x2a9bc debug: &_end 0x35944, &__stack 0x400000 debug: Memory tests (0x400000 -- 0x2000000) debug: NumberTest: debug: passed debug: MarchTest: debug: passed debug: PermTest: debug: passed Dass die Box beim Booten mit gedrückt gehaltener Pfeil-Hoch-Taste an dieser Stelle stehen bleibt, ist normal. Wenn Du das Log mit dem Bootmanager machst, steht dann abschließend noch die Zeile dbox2:root> Praktisch als Eingabe-Aufforderung. Mit dem SeriBoxLogger fehlt die Zeile, das ist normal. ˜debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled Da hat sie den Flash-Erase noch nicht begriffen. Wie geschrieben: das ist ein saublödes Gefummel, ich hab damals, als ich das Prozedere mal brauchte, weil die Originalsoftware hinüber war (ich hatte die wegen eines Tests nochmal haben müssen), bestimmt 50 mal gebraucht, bis das Teil endlich begriffen hat, was es machen soll. Im normalen Betrieb hab ich noch nichts weiter feststellen können, also keinerlei offensichtliche Probleme. Beim "Neustarten" der Box oder nach einem Hardwarereset bootet die Box ohne Probleme. Auch wenn ich die Box in den DeepStandby versetze und ein paar Minuten später die Box wieder starte ist alles ok. Das Problem taucht erst auf wenn die Box länger im DeepStandby war. Ich würde mal behaupten, dass dies der Anfang vom Ende der Box ist. Wenn Du's genau wissen willst, solltest Du die Box in einer Werkstatt prüfen lassen, anhand eines Bootlogs lässt sich da leider keine endgültige Aussage treffen. Das Verhalten der Box nach einiger Zeit im Deep Standby oder stromlos deutet aber darauf hin, dass sie am Sterben ist. Ich hatte vor einigen Tagen das Lcd-Display der Box getauscht, daran wird es ja wohl nicht liegen? Höchstens dass Du an der Box herumgebastelt hast, während sie noch am Stromnetz hing, dann kannste ganz schnell den Frontprozessor zum Teufel jagen oder gar die CPU mit beschädigen, wenn Du am Display fummelst. Der Frontprozessor steht nämlich nach wie vor unter Saft, und die CPU hängt ungeschützt am Frontprozessor. Dein beschriebenes Fehlerbild deutet aber nicht auf zerdepperten Frontprozessor oder angeknackste CPU hin, denn wenn die einmal einen weg haben, ändert sich daran auch nichts mehr, wenn die Box warm gelaufen ist. Hier dürfte ziemlich eindeutig der Flash marode geworden sein, oder wie geschrieben das Netzteil. Netzteil kannst Du messen, wenn Du ein Digitalmultimeter hast. Müssen u.a. 3,3V (3,15 bis 3,45) und 5,0V (4,75 bis 5,25) mit maximaler Toleranz +/-5% vorhanden sein, die Spannungen sind lebensnotwendig für CPU, Flash, RAM, Avia und andere Chips. Zusätzlich gibt's noch "Hilfsspannungen" in der Box (Tuner, Display), da tauchen dann noch 12V, 19V, 23V und 33V auf, zumindest bei Nokias. Wird bei Sagem ähnlich sein, ich habe da aber kein Schaltbild vom Netzteil und im Moment auch keins da zum Ausmessen. Netzteil ist allerdings unwahrscheinlich, denn das läuft komplett, solange die Box an der Steckdose hängt. Bleibt also auch im Deep Standby voll in Betrieb. Kannst Du praktisch nur eins machen: die Box komplett laufen lassen. Oder halt nach Deep Standby immer erst mal resetten. Irgendwann wird das aber sicher auch nicht mehr helfen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
MacFco Geschrieben 2. Oktober 2011 Melden Share Geschrieben 2. Oktober 2011 Ich hatte vor einigen Tagen das Lcd-Display der Box getauscht, daran wird es ja wohl nicht liegen? Er hat im ersten Bootlog den Fehler drin... debug: LCD init error -1 ...in den weiteren Logs aber komischerweise dann nicht mehr. Würde also nochmal nachschauen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
frankl Geschrieben 2. Oktober 2011 Autor Melden Share Geschrieben 2. Oktober 2011 Hi, Wie geschrieben: das ist ein saublödes Gefummel, ich hab damals, als ich das Prozedere mal brauchte, weil die Originalsoftware hinüber war (ich hatte die wegen eines Tests nochmal haben müssen), bestimmt 50 mal gebraucht, bis das Teil endlich begriffen hat, was es machen soll. ich probier es noch ein paar mal und wenn nicht R.I.P. Dbox2, irgendwann. Er hat im ersten Bootlog den Fehler drin... debug: LCD init error -1 ...in den weiteren Logs aber komischerweise dann nicht mehr. Würde also nochmal nachschauen. Scheint alles soweit richtig eingebaut zu sein. Da gibt es ja auch nicht so viel falsch zu machen, oder? LG frankl Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 2. Oktober 2011 Melden Share Geschrieben 2. Oktober 2011 Man kann z.B. das Flachbandkabel schief reinwürgen, dann sind Kurzschlüssen benachbarter Kontakte die Folge. Was allerdings mit ziemlicher Sicherheit den Frontprozessor grillt und dabei oft auch noch die CPU mitnimmt. Der LCD init error wäre damit dauerhaft, ein einmal zerdepperter Frontprozessor nimmt auch seinen ordnungsgemäßen Dienst nicht mehr auf, wenn er "Betriebstemperatur" bekommt, da kannst Du dem Teil auch mit einem Fön einheizen - ohne Wirkung. Was mir gerade noch einfällt, was Du noch probieren kannst, falls Du Kältespray hast: Wenn die Box auf Temperatur ist und einwandfrei funktioniert, halte mal mit dem Spray richtig auf den Flashchip drauf und resette die Box dabei. Wenn dann die Box beim Booten plötzlich wieder hängen bleibt, hast Du den schuldigen Teil identifiziert. Aber wie schon weiter oben geschrieben, würde ich die Box einfach dauerhaft an lassen (bzw. Soft-Standby), und wenn sie dann doch irgendwann ganz den Geist aufgibt, in den Kübel damit. Reparatur lohnt mittlerweile kaum noch, weil eine Ersatzkiste auch schon für um die 50 Euro zu bekommen ist - mehr ist die dBox2 auch nicht mehr wert, auch wenn sie immer noch einiges mehr kann als manch aktueller SD-Receiver. Trotzdem hat die Kiste mit ihren rund 12 Jahren auf'm Buckel ihrer Schuldigkeit praktisch Genüge getan und ist nicht mehr ganz zeitgemäß. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
frankl Geschrieben 4. Oktober 2011 Autor Melden Share Geschrieben 4. Oktober 2011 Hi, ich hatte die Box nochmals geöffnet und die Lcd-Kabel überprüft und siehe da, die Box bootet ohne Probleme aus dem Deep-Standby (war über Nacht im Standby). Will mich jetzt aber nicht zu früh freuen. Werd das Ganze die nächsten Tage weiter beobachten. LG frankl Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
frankl Geschrieben 18. Oktober 2011 Autor Melden Share Geschrieben 18. Oktober 2011 Hi, gleiche Box ähnliches Problem. Nachdem ich eine Weile keine Probleme mit der Box, beim Booten aus dem Deep-Standby, hatte, macht sie nun wieder Probleme. Die Box bleibt wieder hängen, aber an einer anderen Stelle (siehe Log). Log mit Hänger SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 ÿdebug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: LCD init error -1 debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS debug: Got Block #0008debug: Got Block #0012debug: Got Block #0016debug: Got Block #0020debug: Got Block #0024debug: Got Block #0028debug: Got Block #0032debug: Got Block #0036debug: Got Block #0040debug: Got Block #0044 will verify ELF image, start= 0x800000, size= 174720 verify sig: 262 Branching to 0x40100 U-Boot 2011.06 (Tuxbox) (Jul 15 2011 - 08:36:14) CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Sagem, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MiB Flash: 8 MiB Scanning JFFS2 FS: . | . / - \ | / . - \ . done. env: found console with value ttyS0 env: found lcd_inverse with value 0 env: found lcd_contrast with value 15 FB: ready In: serial Out: serial Err: serial Net: SCC LCD: ready Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 1 0 ............................................................... done Un-Protected 63 sectors ### FS (squashfs) loading 'vmlinuz' to 0x200000 ### FS load complete: 666611 bytes loaded to 0x200000 ## Booting kernel from Legacy Image at 00200000 ... Image Name: Linux-2.4.37.11-dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 666547 Bytes = 650.9 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.37.11-dbox2 (image@server) (gcc version 3.4.6) #1 Sa 24. Sep 15:21:40 CEST 2011 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex= Decrementer Frequency = 247500000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x2000) Console: colour dummy device 80x25 Calibrating delay loop... 65.74 BogoMIPS Memory: 30832k available (1132k kernel code, 344k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. squashfs: version 3.0 (2006/03/15) Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured half-duplex mode enabled eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:32:e0:ed loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00040000 : "FLFS (U-Boot)" 0x00040000-0x005e0000 : "root (squashfs+lzma)" 0x005e0000-0x00800000 : "var (jffs2)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.18.5 (2011-09-24 16:06:29 CEST) starting pid 8, tty '': '/etc/init.d/rcS' mount: using /etc/fstab Eep. Child "satellites.xml" (ino #195) of dir ino #150 doesn't exist! ##### Image-Version: Keywelt_Jul2011_V1.30 ##### Mon Aug 1 18:57:00 UTC 2011 event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ tuxbox: no IDE-Interface detected Detected STB: Vendor: Sagem Model: D-BOX2 [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 $Id: cam.c,v 1.33 2011/06/19 11:49:27 rhabarber1848 Exp $ $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ avia_av: $Id: avia_av_core.c,v 1.106 2011/06/19 11:49:27 rhabarber1848 Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av: AVIA 600L found. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $ avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $ avia_gt_core: autodetecting chip type... eNX avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $ avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $ avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.215 2011/06/19 11:51:17 rhabarber1848 Exp $ avia_gt_ucode: loaded ucode v0014 avia_gt_ucode: ucode section filters disabled. avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning... avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $ avia_gt_gv: set_input_size (width=720, height=576) avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $ avia_gt_pcm_set_rate(44100) avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $ avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $ avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $ avia_gt_core: Loaded AViA eNX/GTX driver avia_av_core: Starting avia_gt_wdt thread. SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 insmod: not an ELF file lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34531] SQUASHFS error: Unable to read page, block 34531, size 573e SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 insmod: not an ELF fileSQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34531] SQUASHFS error: Unable to read page, block 34531, size 573e SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34531] SQUASHFS error: Unable to read page, block 34531, size 573e SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 insmod: not an ELF file avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.14 2011/06/19 11:49:27 rhabarber1848 Exp $ Node header CRC failed at 001ae370. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00ff00ff) != totlen from node ref (0x00000044) Node header CRC failed at 0002257c. But it must have been OK earlier. Node was: { 01f7, 21f7, 01f701f7, 01f701f7 } Node totlen on flash (0x00000000) != totlen from node ref (0x00000034) jffs2_do_read_inode(): No data nodes found for ino #60 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 ifup: can't open '/etc/network/interfaces': Input/output error SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [255d9d] SQUASHFS error: Unable to read page, block 255d9d, size 2426 Node header CRC failed at 00183f0c. But it must have been OK earlier. Node was: { c198, e198, c198c198, c198c198 } Node totlen on flash (0xffffffff) != totlen from node ref (0x00000078) jffs2_do_read_inode(): No data nodes found for ino #297 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d Bad emulation wget/84 NIP: 0ff56a60 instruction: 00000000 opcode: 0 A: 0 B: 0 C: 0 code: 0 rc: 0 pte @ 0x ff56a60: (0xc1cc80fc)->(0xc1bdbd58)->0x01b96889 RPN: 01b96 PP: 2 SPS: 1 SH: 0 CI: 0 v: 1 Kernel VA for NIP 0xc1b96a60 pte @ 0xc1b96a60: no pmd Floating point exception Node header CRC failed at 001ade48. But it must have been OK earlier. Node was: { 01a7, 21a7, 01a701a7, 01a701a7 } Node totlen on flash (0x01a701a7) != totlen from node ref (0x00000130) jffs2_do_read_inode(): No data nodes found for ino #55 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34ea6f] SQUASHFS error: Unable to read page, block 34ea6f, size 4713 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34ea6f] SQUASHFS error: Unable to read page, block 34ea6f, size 4713 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34ea6f] SQUASHFS error: Unable to read page, block 34ea6f, size 4713 insmod: not an ELF file ves1x93: Detected ves1993 DVB: registering frontend 0:0 (VES1993)... SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 insmod: not an ELF file SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 insmod: not an ELF file insmod: unresolved symbol avia_gt_napi_dvr_send insmod: unresolved symbol avia_gt_set_playback_mode Node header CRC failed at 001836b0. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0xffffffff) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #349 insmod: warning: kernel-module version mismatch multicam was compiled for kernel version 2.4.37-dbox2 while this kernel is version 2.4.37.11-dbox2 DBox2 Multicam Driver v1.01 skars & doz21 Node header CRC failed at 001ad1a4. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0x01f701f7) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #34 Node header CRC failed at 001ad2e4. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0x01f701f7) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #36 Node header CRC failed at 0018906c. But it must have been OK earlier. Node was: { 00ff, 20ff, 00ff00ff, 00000000 } Node totlen on flash (0xc1ffc1ff) != totlen from node ref (0x00000084) jffs2_do_read_inode(): No data nodes found for ino #57 /var/etc/init.d/rcS: line 299: can't create /etc/issue.net: Input/output error Node header CRC failed at 00062424. But it must have been OK earlier. Node was: { 2400, 2400, 24002400, 24002400 } Node totlen on flash (0x01b301b3) != totlen from node ref (0x00000044) Node header CRC failed at 00000e14. But it must have been OK earlier. Node was: { 00ff, 20ff, 00ff00ff, 00ff00ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000d80. But it must have been OK earlier. Node was: { c38a, e38a, c38ac38a, c38ac38a } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000cec. But it must have been OK earlier. Node was: { c1ff, e1ff, c1ffc1ff, c1ffc1ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000c58. But it must have been OK earlier. Node was: { c01f, e01f, c01fc01f, c01fc01f } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000bb4. But it must have been OK earlier. Node was: { 00ff, 20ff, 00ff00ff, 00ff00ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x0000003c) Node header CRC failed at 00000b18. But it must have been OK earlier. Node was: { c1ff, e1ff, c1ffc1ff, c1ffc1ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000038) Node header CRC failed at 00000a84. But it must have been OK earlier. Node was: { c014, e014, c014c014, c014c014 } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 000009f0. But it must have been OK earlier. Node was: { c01f, e01f, c01fc01f, c01fc01f } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 0000095c. But it must have been OK earlier. Node was: { c1ff, e1ff, c1ffc1ff, c1ffc1ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) jffs2_do_read_inode(): No data nodes found for ino #151 mkdir: can't create directory '/var/tuxbox/fonts': File exists /var/etc/init.d/rcS: cd: line 329: can't cd to /var/tuxbox/fonts/ SR.4 or SR.5 bits set in buffer write (status 70). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: tuxtxt.otb: Read-only file system SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: tuxtxt.ttf: Read-only file system SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: pakenham.ttf: Read-only file system SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: bluehigh.ttf: Read-only file system Node CRC 04ff36ff != calculated CRC 8aa44091 for node at 000203e0 Node CRC 00ff06ff != calculated CRC d893add9 for node at 000203e0 [: missing ] starting pid 129, tty '': '/etc/init.d/start' Node header CRC failed at 0002071c. But it must have been OK earlier. Node was: { c1f7, e1f7, c1f7c1f7, 00000000 } Node totlen on flash (0x00ff00ff) != totlen from node ref (0x000001b4) jffs2_do_read_inode(): No data nodes found for ino #74 can't run '/etc/init.d/start': Input/output error nach einem Harwarereset bootet die Box wieder ohne Probleme ÿdebug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: LCD init error -1 debug: BMon V1.2 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-99.b5.b8.07.00.00-70 debug: HWrev 21 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS debug: Got Block #0008debug: Got Block #0012debug: Got Block #0016debug: Got Block #0020debug: Got Block #0024debug: Got Block #0028debug: Got Block #0032debug: Got Block #0036debug: Got Block #0040debug: Got Block #0044 will verify ELF image, start= 0x800000, size= 174720 verify sig: 262 Branching to 0x40100 U-Boot 2011.06 (Tuxbox) (Jul 15 2011 - 08:36:14) CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Sagem, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MiB Flash: 8 MiB Scanning JFFS2 FS: . | . / - \ | / . - \ . done. env: found console with value ttyS0 env: found lcd_inverse with value 0 env: found lcd_contrast with value 15 FB: ready In: serial Out: serial Err: serial Net: SCC LCD: ready Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 1 0 ............................................................... done Un-Protected 63 sectors ### FS (squashfs) loading 'vmlinuz' to 0x200000 ### FS load complete: 666611 bytes loaded to 0x200000 ## Booting kernel from Legacy Image at 00200000 ... Image Name: Linux-2.4.37.11-dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 666547 Bytes = 650.9 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.37.11-dbox2 (image@server) (gcc version 3.4.6) #1 Sa 24. Sep 15:21:40 CEST 2011 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex= Decrementer Frequency = 247500000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x2000) Console: colour dummy device 80x25 Calibrating delay loop... 65.74 BogoMIPS Memory: 30832k available (1132k kernel code, 344k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc. squashfs: version 3.0 (2006/03/15) Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured half-duplex mode enabled eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:32:e0:ed loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00040000 : "FLFS (U-Boot)" 0x00040000-0x005e0000 : "root (squashfs+lzma)" 0x005e0000-0x00800000 : "var (jffs2)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.18.5 (2011-09-24 16:06:29 CEST) starting pid 8, tty '': '/etc/init.d/rcS' mount: using /etc/fstab Eep. Child "satellites.xml" (ino #195) of dir ino #150 doesn't exist! ##### Image-Version: Keywelt_Jul2011_V1.30 ##### Mon Aug 1 18:57:00 UTC 2011 event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ tuxbox: no IDE-Interface detected Detected STB: Vendor: Sagem Model: D-BOX2 [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 $Id: cam.c,v 1.33 2011/06/19 11:49:27 rhabarber1848 Exp $ $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ avia_av: $Id: avia_av_core.c,v 1.106 2011/06/19 11:49:27 rhabarber1848 Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av: AVIA 600L found. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $ avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $ avia_gt_core: autodetecting chip type... eNX avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $ avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $ avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.215 2011/06/19 11:51:17 rhabarber1848 Exp $ avia_gt_ucode: loaded ucode v0014 avia_gt_ucode: ucode section filters disabled. avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning... avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $ avia_gt_gv: set_input_size (width=720, height=576) avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $ avia_gt_pcm_set_rate(44100) avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $ avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $ avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $ avia_gt_core: Loaded AViA eNX/GTX driver avia_av_core: Starting avia_gt_wdt thread. SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 insmod: not an ELF file lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34531] SQUASHFS error: Unable to read page, block 34531, size 573e SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 insmod: not an ELF fileSQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34531] SQUASHFS error: Unable to read page, block 34531, size 573e SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34531] SQUASHFS error: Unable to read page, block 34531, size 573e SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 insmod: not an ELF file avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.14 2011/06/19 11:49:27 rhabarber1848 Exp $ Node header CRC failed at 001ae370. But it must have been OK earlier. Node was: { ffff, ffff, ffffffff, ffffffff } Node totlen on flash (0x00ff00ff) != totlen from node ref (0x00000044) Node header CRC failed at 0002257c. But it must have been OK earlier. Node was: { 01f7, 21f7, 01f701f7, 01f701f7 } Node totlen on flash (0x00000000) != totlen from node ref (0x00000034) jffs2_do_read_inode(): No data nodes found for ino #60 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [45a57] SQUASHFS error: Unable to read page, block 45a57, size 3048 ifup: can't open '/etc/network/interfaces': Input/output error SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [255d9d] SQUASHFS error: Unable to read page, block 255d9d, size 2426 Node header CRC failed at 00183f0c. But it must have been OK earlier. Node was: { c198, e198, c198c198, c198c198 } Node totlen on flash (0xffffffff) != totlen from node ref (0x00000078) jffs2_do_read_inode(): No data nodes found for ino #297 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read page, block 1a5ccb, size 648d Bad emulation wget/84 NIP: 0ff56a60 instruction: 00000000 opcode: 0 A: 0 B: 0 C: 0 code: 0 rc: 0 pte @ 0x ff56a60: (0xc1cc80fc)->(0xc1bdbd58)->0x01b96889 RPN: 01b96 PP: 2 SPS: 1 SH: 0 CI: 0 v: 1 Kernel VA for NIP 0xc1b96a60 pte @ 0xc1b96a60: no pmd Floating point exception Node header CRC failed at 001ade48. But it must have been OK earlier. Node was: { 01a7, 21a7, 01a701a7, 01a701a7 } Node totlen on flash (0x01a701a7) != totlen from node ref (0x00000130) jffs2_do_read_inode(): No data nodes found for ino #55 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34ea6f] SQUASHFS error: Unable to read page, block 34ea6f, size 4713 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34ea6f] SQUASHFS error: Unable to read page, block 34ea6f, size 4713 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [34ea6f] SQUASHFS error: Unable to read page, block 34ea6f, size 4713 insmod: not an ELF file ves1x93: Detected ves1993 DVB: registering frontend 0:0 (VES1993)... SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [35d05e] SQUASHFS error: Unable to read page, block 35d05e, size 46d2 insmod: not an ELF file SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 SQUASHFS error: lzma_fs returned unexpected result 0x1 SQUASHFS error: Unable to read fragment cache block [361730] SQUASHFS error: Unable to read page, block 361730, size 2d97 insmod: not an ELF file insmod: unresolved symbol avia_gt_napi_dvr_send insmod: unresolved symbol avia_gt_set_playback_mode Node header CRC failed at 001836b0. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0xffffffff) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #349 insmod: warning: kernel-module version mismatch multicam was compiled for kernel version 2.4.37-dbox2 while this kernel is version 2.4.37.11-dbox2 DBox2 Multicam Driver v1.01 skars & doz21 Node header CRC failed at 001ad1a4. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0x01f701f7) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #34 Node header CRC failed at 001ad2e4. But it must have been OK earlier. Node was: { 0000, 2000, 00000000, 00000000 } Node totlen on flash (0x01f701f7) != totlen from node ref (0x00000044) jffs2_do_read_inode(): No data nodes found for ino #36 Node header CRC failed at 0018906c. But it must have been OK earlier. Node was: { 00ff, 20ff, 00ff00ff, 00000000 } Node totlen on flash (0xc1ffc1ff) != totlen from node ref (0x00000084) jffs2_do_read_inode(): No data nodes found for ino #57 /var/etc/init.d/rcS: line 299: can't create /etc/issue.net: Input/output error Node header CRC failed at 00062424. But it must have been OK earlier. Node was: { 2400, 2400, 24002400, 24002400 } Node totlen on flash (0x01b301b3) != totlen from node ref (0x00000044) Node header CRC failed at 00000e14. But it must have been OK earlier. Node was: { 00ff, 20ff, 00ff00ff, 00ff00ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000d80. But it must have been OK earlier. Node was: { c38a, e38a, c38ac38a, c38ac38a } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000cec. But it must have been OK earlier. Node was: { c1ff, e1ff, c1ffc1ff, c1ffc1ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000c58. But it must have been OK earlier. Node was: { c01f, e01f, c01fc01f, c01fc01f } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 00000bb4. But it must have been OK earlier. Node was: { 00ff, 20ff, 00ff00ff, 00ff00ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x0000003c) Node header CRC failed at 00000b18. But it must have been OK earlier. Node was: { c1ff, e1ff, c1ffc1ff, c1ffc1ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000038) Node header CRC failed at 00000a84. But it must have been OK earlier. Node was: { c014, e014, c014c014, c014c014 } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 000009f0. But it must have been OK earlier. Node was: { c01f, e01f, c01fc01f, c01fc01f } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) Node header CRC failed at 0000095c. But it must have been OK earlier. Node was: { c1ff, e1ff, c1ffc1ff, c1ffc1ff } Node totlen on flash (0xc0ffc0ff) != totlen from node ref (0x00000034) jffs2_do_read_inode(): No data nodes found for ino #151 mkdir: can't create directory '/var/tuxbox/fonts': File exists /var/etc/init.d/rcS: cd: line 329: can't cd to /var/tuxbox/fonts/ SR.4 or SR.5 bits set in buffer write (status 70). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: tuxtxt.otb: Read-only file system SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 94 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: tuxtxt.ttf: Read-only file system SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: pakenham.ttf: Read-only file system SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero SR.4 or SR.5 bits set in buffer write (status ffff). Clearing. Write of 96 bytes at 0x0018b3d0 failed. returned -30, retlen 0 Not marking the space at 0x0018b3d0 as dirty because the flash driver returned retlen zero ln: bluehigh.ttf: Read-only file system Node CRC 04ff36ff != calculated CRC 8aa44091 for node at 000203e0 Node CRC 00ff06ff != calculated CRC d893add9 for node at 000203e0 [: missing ] starting pid 129, tty '': '/etc/init.d/start' Node header CRC failed at 0002071c. But it must have been OK earlier. Node was: { c1f7, e1f7, c1f7c1f7, 00000000 } Node totlen on flash (0x00ff00ff) != totlen from node ref (0x000001b4) jffs2_do_read_inode(): No data nodes found for ino #74 can't run '/etc/init.d/start': Input/output error LG frankl Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 18. Oktober 2011 Melden Share Geschrieben 18. Oktober 2011 Solltest Dich wohl damit abfinden, dass die Box dabei ist, das Zeitliche zu segnen. Irgendwann wird sie wohl komplett ausfallen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Empfohlene Beiträge
Archiviert
Dieses Thema ist jetzt archiviert und für weitere Antworten gesperrt.