McCoRmIcK Geschrieben 6. September 2011 Melden Share Geschrieben 6. September 2011 Hallo Habe für meinen Bruder eine Sagem DBox2 Kabel mit 1XI bei eBay gekauft wo bereits Linux vorinstalliert war. Wollte direkt das Keywelt Image flashen aber leider bekomm ich keine Netzwerk verbindung. Hab dann erstmal nicht lange rum gefackelt und komplett über Nullmodem Kabel geflasht. Nun läuft das Keywelt Image aber ich bekomme immer noch keine Netzwerkverbindung. Folgendes habe ich schon getestet. Box <-> Switch <-> PC, IPs festgelegt, MediaSense aus, PC(WinXP) auf 10mbit Half Duplex mit Patch Kabel Box <-> PC, IPs festgelegt, MediaSense aus, PC(WinXP) auf 10mbit Half Duplex mit Crossover Kabel Dbox <-> Router <-> PC, DHCP ein an der Box mit Patch Kabel Es ist immer jeweils eine Lampe an der Netzwerkbuchse an, also am PC oder halt am Switch bzw. am Router. Über DHCP erhält die Box garkeine IP oder der gleichen und bei Netzwerktest kommt dann die Meldung das das Netzwerk nicht aktiv ist. Stelle ich die IP Fix ein, funktioniert nur der Ping test zur Box selbst aber kein Ping von PC zur Box. Egal wie ich anklemme und einstelle. Habe früher bereits eine Nokia Dbox2 gemacht und nie solche Probelme gehabt. Gibt es noch etwas was ich ausprobieren kann? Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
MacFco Geschrieben 6. September 2011 Melden Share Geschrieben 6. September 2011 Hast ja schon einiges versucht. Obwohl die Link-LED anscheinend an ist, könnte es trotzdem der Netzwerk-Chip/Phys, Prozessor oder eine kalte Lötstelle der DBox sein. eBay ist halt so ne Sache. Mach mal ein komplettes serielles Bootlog und stell es in Spoiler-Tags hier rein, vlt. sieht man ja was. Am Besten mit DHCP ein, die Anfrage an den Router sieht man nämlich im Log. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
McCoRmIcK Geschrieben 6. September 2011 Autor Melden Share Geschrieben 6. September 2011 debug: DDF: Calibrating delay loop... debug: DDF: 66.76 BogoMIPS debug: BMon V1.3 mID 03 debug: feID 00 enxID 03 debug: fpID 52 dsID 01-f8.21.3f.08.00.00-2c debug: HWrev 61 FPrev 0.23 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS debug: Got Block #0044 will verify ELF image, start= 0x800000, size= 174720 verify sig: 262 Branching to 0x40100 U-Boot 2011.06 (Tuxbox) (Jul 15 2011 - 08:36:14) CPU: PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Sagem, BMon V1.3 Watchdog enabled I2C: ready DRAM: 32 MiB Flash: 8 MiB Scanning JFFS2 FS: ... done. env: found console with value ttyS0 env: found baudrate with value 9600 env: found dbox_duplex with value 0 env: found lcd_inverse with value 0 env: found lcd_contrast with value 15 env: found lcd_bias with value 0 FB: ready In: serial Out: serial Err: serial Net: SCC LCD: ready Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 ............................................................... done Un-Protected 63 sectors ### FS (squashfs) loading 'vmlinuz' to 0x200000 ### FS load complete: 666609 bytes loaded to 0x200000 ## Booting kernel from Legacy Image at 00200000 ... Image Name: Linux-2.4.37.11-dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 666545 Bytes = 650.9 KiB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.37.11-dbox2 (image@server) (gcc version 3.4.6) #5 Fr 15. Jul 08:37:12 CEST 2011 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600 dbox_duplex=0 Decrementer Frequency = 247500000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x2000) Console: colour dummy device 80x25 Calibrating delay loop... 65.74 BogoMIPS Memory: 30832k available (1132k kernel code, 344k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. squashfs: version 3.0 (2006/03/15) Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGÿttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured half-duplex mode enabled eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:3d:cd:d3 loop: loaded (max 8 devices) D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled Creating 6 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00040000 : "FLFS (U-Boot)" 0x00040000-0x005e0000 : "root (squashfs+lzma)" 0x005e0000-0x00800000 : "var (jffs2)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. VFS: Mounted root (squashfs filesystem) readonly. Mounted devfs on /dev Freeing unused kernel memory: 60k init init started: BusyBox v1.18.5 (2011-08-01 18:48:25 CEST) starting pid 8, tty '': '/etc/init.d/rcS' mount: using /etc/fstab ##### Image-Version: Keywelt_Jul2011_V1.00 ##### Mon Aug 1 18:57:00 UTC 2011 event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ tuxbox: no IDE-Interface detected Detected STB: Vendor: Sagem Model: D-BOX2 [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 $Id: cam.c,v 1.33 2011/06/19 11:49:27 rhabarber1848 Exp $ $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ avia_av: $Id: avia_av_core.c,v 1.106 2011/06/19 11:49:27 rhabarber1848 Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av: AVIA 600L found. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $ avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $ avia_gt_core: autodetecting chip type... eNX avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $ avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $ avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.215 2011/06/19 11:51:17 rhabarber1848 Exp $ avia_gt_ucode: loaded ucode v0014 avia_gt_ucode: ucode section filters disabled. avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning... avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $ avia_gt_gv: set_input_size (width=720, height=576) avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $ avia_gt_pcm_set_rate(44100) avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $ avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $ avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $ avia_gt_core: Loaded AViA eNX/GTX driver avia_av_core: Starting avia_gt_wdt thread. avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $ avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) Console: switching to colour frame buffer device 82x32 avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $ avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $ avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $ avia_gt_pcm_set_rate(44100) avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.14 2011/06/19 11:49:27 rhabarber1848 Exp $ udhcpc (v1.18.5) started Setting IP address 0.0.0.0 on eth0 Sending discover... Sending discover... Sending discover... No lease, forking to background wget: can't connect to remote host (127.0.0.1): Connection refused DVB: registering frontend 0:0 (Atmel AT76C651B with TUA6010XS)... avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $ avia_gt_napi: $Id: avia_gt_napi.c,v 1.208 2011/06/19 11:51:17 rhabarber1848 Exp $ insmod: warning: kernel-module version mismatch multicam was compiled for kernel version 2.4.37-dbox2 while this kernel is version 2.4.37.11-dbox2 DBox2 Multicam Driver v1.01 skars & doz21 Achtung, cam-alpha.bin steht in einer Kabelbox auf Sat! starting pid 187, tty '': '/etc/init.d/start' Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.335 2011/06/ 19 12:31:44 rhabarber1848 Exp $ [sectionsd] FreeSat enabled [sectionsd] Caching max 3000 events [sectionsd] Caching 4 days [sectionsd] Caching 12 hours Extended Text [sectionsd] Events are old 120min after their end time /var/tuxbox/config/zapit/epgfilter.xml: No such file or directory /var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory /var/tuxbox/config/mybouquets.xml: No such file or directory [ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading. [ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading. [timerd] woke up from timer? false! /var/plugins/operations camd_init /var/plugins/operations cardserver_start $Id: zapit.cpp,v 1.440k 2009/09/18 20:30:00 rhabarber1848 & Worschter & SnowHead Exp $ [zapit] PMT update enabled [frontend] uncommitted_switch_mode 0 auto_fec 0 /var/tuxbox/config/zapit/services.xml: No such file or directory [controld] Boxtype detected: (3, Sagem D-BOX2) [controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1 /var/plugins/operations sect_renice [CVideo::setVideoFormat] output format: 4:3(LB) neutrino: /lib/libpng12.so.0: no version information available (required by neutrino) neutrino: /lib/libpng12.so.0: no version information available (required by /lib/liblcddisplay.so.0) /var/plugins/operations camd_start starte camd2 [camd2] EMM : active [camd2] Socket=/tmp/camd.sock02 [camd] ca system id: 1702 starting /bin/neutrino [neutrino] frameBuffer Instance created 812k video mem avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) [neutrino] enable flash [neutrino] Software update enabled [lcdd] time-skin not found -> using default... [lcdd] weekday-skin not found -> using default... [lcdd] date-skin not found -> using default... [lcdd] month-skin not found -> using default... [LCDFONT] initializing core... [LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular) [LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold) [LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold) [LCDFONT] Intializing font cache... [LCDFONT] FTC_Face_Requester (Fix14/Bold) [neutrino] SetupFonts filename: /share/fonts/micron.ttf fontname: Micron [rcinput] no file /var/tuxbox/config/rc.conf was found /dev/input/event1: No such file or directory [neutrino] menue setup [neutrino] init menus... [neutrino] GUI-Personalize instance created... [neutrino] found esound, adding personalized esound entry to mainmenue [network config] Instance created [neutrino] setRepeat: delay=150 period=125 use kernel-repeat: no [neutrino] registering as event client [scan-setup] received 43 providers /bin/nhttpd: /lib/libpng12.so.0: no version information available (required by /lib/liblcddisplay.so.0) [yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0) [LCDFONT] initializing core... [LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular) [LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold) [LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular) [LCDFONT] Intializing font cache... [yhttpd] Webserver starting... [sectionsd] getUTC: read: Connection timed out [sectionsd] getUTC: read: Connection timed out [sectionsd] getUTC: read: Connection timed out [sectionsd] getUTC: read: Connection timed out [sectionsd] getUTC: read: Connection timed out [sectionsd] getUTC: read: Connection timed out [sectionsd] getUTC: read: Connection timed out [sectionsd] getUTC: read: Connection timed out [neutrino] no file /var/tuxbox/config/init.end was found [neutrino] initialized everything Die Box hängt zur zeit nicht am TV, nur am Router und am PC mit Nullmodem. Wegen eBay ist nicht so schlimm, hab bei nem Händler gekauft der 6 Monate Gewähr gibt. Das ist nicht das Problem, hab nur keine Lust auf wieder hin und her schicken Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
McCoRmIcK Geschrieben 8. September 2011 Autor Melden Share Geschrieben 8. September 2011 push Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
merkwuerden Geschrieben 8. September 2011 Melden Share Geschrieben 8. September 2011 Dein "push" kannst Du bitte bleiben lassen. Wenn jemand was zu dem Problem sagen kann, wird er das auch so tun. Meine Meinung: Netzwerkchip der Box im Eimer. Per DHCP ist laut Log auch keine IP erteilt worden, da von außen keine Antwort zurück kam. Box Switch PC, IPs festgelegt, MediaSense aus, PC(WinXP) auf 10mbit Half Duplex mit Patch Kabel Über Switch oder Router: Stelle den PC fest auf 100 Half Duplex ein. Es gibt diverse Netzwerkkarten, die mit 10 Half nicht korrekt arbeiten, auch wenn es den Anschein hat. Vor allem 1 GB Karten gehören in diese Kategorie. Womit dann auch eine Direktverbindung mit Crossover nicht funktionieren wird. Media Sensing kannst Du übrigens bei Verbindung über Switch oder Router außer Acht lassen. Das beeinflusst nur das Erkennungsverhalten zwischen PC und Switch/Router, aber nicht die Geräte, die "auf der anderen Seite" dran hängen, darum kümmert sich dann Switch/Router selbst. Sollte sich bei Verbindung PC Switch Box mit fest vergebenen Adressen und Einstellung des PC auf 100 Half auch keine Verbindung erreichen lassen (was ich vermute): Reklamiere die Box, denn dann ist tatsächlich der Netzwerkchip der Box hinüber oder sogar die CPU beschädigt. Der Tausch des Netzwerkchip kostet ca. 35 Euro, mehr ist die ganze Kabelbox nicht mehr wert. Zumal Sagem-Kabelboxen mittlerweile von keinem einzigen Provider mehr supported werden. Und ist die CPU angedeppert (die den kastrierten Netzwerkchip der Box bedienen muss), bekommst Du für die Reparaturkosten 2 bis 3 funktionstüchtige Kabelboxen. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
MacFco Geschrieben 8. September 2011 Melden Share Geschrieben 8. September 2011 @McCoRmIcK Wie @merkwuerden schon schrieb, wahrscheinlich Netzwerk-Chip/Prozessor kaputt. Hau die Box dem Händler um die Ohren mit den Angaben, wie oben, was du schon getestet hast, plus... udhcpc (v1.18.5) started Setting IP address 0.0.0.0 on eth0 Sending discover... Sending discover... Sending discover... No lease, forking to background ...und das muss reichen. PS: Hier im Board gibt es in letzter Zeit, wie ich finde, genügend Angebote, die auch preislich attraktiv sind. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Empfohlene Beiträge
Archiviert
Dieses Thema ist jetzt archiviert und für weitere Antworten gesperrt.