IDE-Interface - kein Harddisk Setup

[jacke67]

Hallo,

ich habe mir das IDE Interface von dbox2.net eingebaut. Dazu eine neue 2,5" Festplatte.

Mein Problem ist, das ich keinen Menüpunkt finde um die Platte zu formatieren (wie auf der Webseite des Herstellers).

 

Unter Blaue Taste -> HDD/CF/MMC-Check

erscheint: "starte IDE-Treiber..." dann "mounte IDE-Device nach ....". Die Platte läuft an dieser Stelle hörbar an.

Am Schluß erscheint dann folgende Fehlermeldung:

"Fehler: Die Datenpartition konnte nicht gemountet werden.

Wahrscheinlich ist das falsche Dateisystem eingestellt oder die Partition nicht formatiert."

 

Hier noch das bootlog:

®debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID 7a    gtxID 0b
debug: fpID 5a     dsID 01-9b.15.03.07.00.00-28
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug:
BOOTP/TFTP bootstrap loader (v0.3)
debug:
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1
Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 171660
verify sig: 262
Branching to 0x40000


U-Boot 2009.08 (Tuxbox) (Sep 26 2009 - 14:36:43)

CPU:   PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
        *** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
      Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS: .... done.
env: found console with value ttyS0
env: found lcd_inverse with value 0
env: found lcd_contrast with value 15
FB:    ready
In:    serial
Out:   serial
Err:   serial
Net:   SCC ETHERNET
LCD:   ready

Options:
 1: Console on null
 2: Console on ttyS0
 3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  0
............................................................... done
Un-Protected 63 sectors
### FS (squashfs) loading 'vmlinuz' to 0x200000
### FS load complete: 671052 bytes loaded to 0x200000
## Booting kernel from Legacy Image at 00200000 ...
  Image Name:   Linux-2.4.37.6-dbox2
  Image Type:   PowerPC Linux Kernel Image (gzip compressed)
  Data Size:    670988 Bytes = 655.3 kB
  Load Address: 00000000
  Entry Point:  00000000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Linux version 2.4.37.6-dbox2 (image@Server) (gcc version 3.4.6) #26 Sa Sep 26 14
:37:12 CEST 2009
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs console=ttyS0,9600
dbox_duplex=
Decrementer Frequency = 252000000/60
m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)
m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)
Console: colour dummy device 80x25
Calibrating delay loop... 66.96 BogoMIPS
Memory: 30824k available (1144k kernel code, 340k data, 60k init, 0k highmem)
Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
squashfs: version 3.0 (2006/03/15) Phillip Lougher
i2c-core.o: i2c core module version 2.6.1 (20010830)
i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)
CPM UART driver version 0.04
ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2
pty: 256 Unix98 ptys configured
half-duplex mode enabled
eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:12:ec:a1
loop: loaded (max 8 devices)
D-Box 2 flash driver (size->0x800000 mem->0x10000000)
D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank
Intel/Sharp Extended Query Table at 0x0035
cfi_cmdset_0001: Erase suspend on write enabled
Creating 6 MTD partitions on "D-Box 2 flash memory":
0x00000000-0x00020000 : "BR bootloader"
0x00020000-0x00040000 : "FLFS (U-Boot)"
0x00040000-0x005e0000 : "root (squashfs+lzma)"
0x005e0000-0x00800000 : "var (jffs2)"
0x00020000-0x00800000 : "Flash without bootloader"
0x00000000-0x00800000 : "Complete Flash"
Linux video capture interface: v1.00
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k init
init started: BusyBox v1.14.4 (2009-09-26 14:42:24 CEST)
starting pid 8, tty '': '/etc/init.d/rcS'
mount: using /etc/fstab


##### Image-Version: Keywelt_Sep2009_V1 #####

Sat Sep 26 14:57:00 UTC 2009
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $
tuxbox: IDE-Interface detected, Vendor: DboxBaer or kpt.ahab/Stingray
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
dboxide: $Id: main.c,v 1.12 2007/11/03 10:32:16 (alt. IRQ) dbt Exp $
ide: late registration of driver.
dboxide: activating cs2
dboxide: address space of IDE-Interface is at: 0xc3894000
Probing IDE interface ide0...
hda: SAMSUNG HM160HC, ATA DISK drive
ide0 at 0x010-0x017,0x04e on irq 47
warte auf 'init_ide'
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 312581808 sectors (160042 MB) w/8192KiB Cache, CHS=19457/255/63
Partition check:
/dev/ide/host0/bus0/target0/lun0: unknown partition table
warte auf 'init_ide'
mount: mounting /dev/ide/host0/bus0/target0/lun0/part2 on /hdd failed: No such f
ile or directory

/dev/ide/host0/bus0/target0/lun0/disc:
setting AAM level to 0x80 (128)
setting drive write-caching to 0 (off)
setting standby to 72
(6 minutes 0 seconds)
'init_ide' fertig
Detected STB:
 Vendor: Nokia
 Model: D-BOX2
[i2c-8xx]: mpc 8xx i2c init
[i2c-8xx]: adapter: 0
insmod: warning: kernel-module version mismatch
       dbox2_fp_input was compiled for kernel version 2.4.37-dbox2
       while this kernel is version 2.4.37.6-dbox2
$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $
$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $
DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).
dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter
$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $
avia_av: $Id: avia_av_core.c,v 1.100 2009/09/11 05:58:41 rhabarber1848 Exp $
avia_av_core: Starting avia_av_wdt thread.
avia_av: AVIA 500 LB4 found, sptsfix is off
avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $
avia_av_proc: $Id: avia_av_proc.c,v 1.15 2007/07/29 18:14:12 papst Exp $
avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $
avia_gt_core: autodetecting chip type... GTX
avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $
avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $
avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $
avia_gt_core: masking unhandled irq reg 1 bit 11
avia_gt_core: masking unhandled irq reg 1 bit 13
avia_gt_ucode: loaded ucode v0014
avia_gt_ucode: ucode section filters disabled.
avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...
avia_gt_core: masking unhandled irq reg 0 bit 6
avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $
avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $
avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $
avia_gt_core: Loaded AViA eNX/GTX driver
avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
Console: switching to colour frame buffer device 82x32
avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device
lcd.o: init lcd driver module
lcd.o: found KS0713/SED153X lcd interface
avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $
avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $
avia_oss: $Id: avia_gt_oss.c,v 1.28 2009/03/22 12:37:58 rhabarber1848 Exp $
avia_gt_pcm_set_rate(44100)
avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $
DVB: VES1820(0): pwm=0x48
DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...
avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $
avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $
insmod: warning: kernel-module version mismatch
       multicam was compiled for kernel version 2.4.37-dbox2
       while this kernel is version 2.4.37.6-dbox2
DBox2 Multicam Driver v1.01 skars & doz21 
starting pid 212, tty '': '/etc/init.d/start'

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.306 2009/09/
14 13:33:28 seife Exp $
[sectionsd] Caching max 1500 events
[sectionsd] Caching 4 days
[sectionsd] Caching 12 hours Extended Text
[sectionsd] Events are old 120min after their end time
/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory
/var/tuxbox/config/zapit/dvbtimefilter.xml: No such file or directory
/var/tuxbox/config/mybouquets.xml: No such file or directory
[ConfigFile] Unable to open file /var/tuxbox/config/timerd.conf for reading.
[timerd] woke up from timer? false!
/var/plugins/operations camd_init
/var/plugins/operations cardserver_start
$Id: zapit.cpp,v 1.440k 2009/09/18 20:30:00 rhabarber1848 & Worschter & SnowHead
Exp $
[zapit] PMT update enabled
[frontend] uncommitted_switch_mode 0 auto_fec 0
avia_gt_core: masking unhandled irq reg 0 bit 7
/var/tuxbox/config/zapit/services.xml: No such file or directory
[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[CVideo::setVideoFormat] output format: 4:3(LB)
/bin/nhttpd: /lib/libpng12.so.0: no version information available (required by /
lib/liblcddisplay.so.0)
[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf.../var/plugins/operations cam
d_start
OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
[yhttpd] Webserver starting...
/var/plugins/operations sect_renice
starte camd2
[camd2] EMM : active
[camd2] Socket=/tmp/camd.sock02
[camd] ca system id: 1722
neutrino: /lib/libpng12.so.0: no version information available (required by neut
rino)
neutrino: /lib/libpng12.so.0: no version information available (required by /lib
/liblcddisplay.so.0)
starting /bin/neutrino
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)
avia_gt_gv: set_input_size (width=720, height=576)
[neutrino] enable flash
[neutrino] Software update enabled
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix14/Bold)
[rcinput] no file /var/tuxbox/config/rc.conf was found
/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] found esound, adding to mainmenue/personalize
[neutrino] can not use input repeat on fd_rc[0]: 22 (Invalid argument)
[neutrino] setRepeat: delay=150 period=125 use kernel-repeat: no
[neutrino] registering as event client
[sectionsd] getUTC: read: Connection timed out

 

Bin für jeden Tip dankbar.

 

Grüße

jacke67

[Keyjockey]

Blaue Taste, Keywelt-Menü, System Menü, HDD-Setup Tool.

Danach nicht vergessen ein Aufnahmeverzeichnis anzulegen (DBox-Taste, Einstellungen, Aufnahme, Aufnahmegerät Direkt (Datei) und dann unten Direktaufnahmeeinstellungen.

 

Viel Spaß mit der HDD in deiner Box.

[jacke67]

super hat geklappt. ich hatte schon ne ganze weile vergeblich gesucht.

muss die box nur noch an den fernseher hängen und mal die aufnahme testen.

 

danke!

 

gruß

jacke67

[unicorn0815]

Mein Problem ist, das ich keinen Menüpunkt finde um die Platte zu formatieren (wie auf der Webseite des Herstellers).

Übrigens gibts HIER eine Übersicht über die vorhandenen Menüs und wo sie zu finden sind