DBox2 hängt gleich nach Start

SpainBox · 5. September 2008

Moin !

Ich habe mir eine zweite Box zugelegt. Nun macht die mir aber Probleme.

Habe ein neues Image aufgespielt und soweit lief auch alles super. Konnte Kanalsuche und die ganzen Einstellungen etc. vornehmen.

Dann starte ich die Box neu und sie hängt sich sofort auf. Kein Bild zu sehen, nur im Display steht der erste Kanal und nix tut sich.

Sie reagiert weder auf die Fernbedienung, noch auf die Steuerung über Netzwerk. (Kann auf die Box zwar zugreifen via IP (dbox yweb), aber sie reagiert nicht auf die Kommandos.)

Ausserdem konnte ich sie nicht über Hallenberg flashen, sondern nur via Expertenfunktion.

Daten:

Nokia Dbox2 Kabel ( Avia 500, 2x Intel)

Bmon1.0

Juli Beta V1 Image

Ist die völlig schrott ?

Und wenn das z.B. ein Imageplatzer ist ?! Kann ich das überhaupt beheben ohne Hallenberg und Expertenfunktion ?

Gruss

rhabarber1848 · 5. September 2008

Ein Bootlog wäre nicht schlecht: http://www.keywelt-board.com/helpdesk/bootlog.htm

FlashNash · 5. September 2008

Wenn die Box beim booten nun hängt oder das Images ´geplatzt´ ist, geht es mit der Expertenfunktion ja nicht mehr, weil Du ja nicht mehr an die Menüoptionen ran kommst. Die Box ist sehr wahrscheinlich nicht geschrottet. Verwende den DBoxBootmanager und verbinde die Box zusätzlich mit einem RS232 Nullmodemkabel. Flasche das Teil mit dem DBoxBootManager neu und berichte mal hier, was danach passiert. Achte auch darauf, dass Du das richtige Image verwendest 1x oder 2x.

Und wie rhabarber1848 schon schrieb, ein Bootlog wäre ned schlecht, damit man weitere Überlegungen anstellen kann.

SpainBox · 5. September 2008

Bootlog muss ich mal sehen ob das funktioniert.

Beim Flashen mit Nullmodemkabel hat er zumindest rumgezickt. Einstellungen und Image waren auch soweit richtig eingestellt. Ich werde mal versuchen ein Bootlog hinzubekommen.

Schon mal Danke..

Gruss

FlashNash · 5. September 2008

Verwende den DBoxBootManager. Der erzeugt auch ein Bootlog. Das Bootlog kannste mit Kopieren (aus DBoxManager) und Einfügen (hier ins Forum) einstellen. Dann sehen wir weiter. Und.. don´t panic.

SpainBox · 5. September 2008

Sauber.. Bootlog hat geklappt..

Aufgefallen ist mir "[AVS] i2c error -121" im unteren Teil des Logs..

Gruss

ÿdebug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS

debug: BMon V1.0 mID 01

debug: feID 7a gtxID 0b

debug: fpID 5a dsID 01-d9.b0.1f.07.00.00-f8

debug: HWrev X5 SWrev 0.81

debug: B/Ex/Fl(MB) 32/00/08

WATCHDOG reset enabled

dbox2:root> debug:

BOOTP/TFTP bootstrap loader (v0.3)

debug:

debug: Transmitting BOOTP request via broadcast

debug: Given up BOOTP/TFTP boot

boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1

Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS

debug: Got Block #0032debug: Got Block #0004debug: Got Block #0008debug: Got Block #0012debug: Got Block #0016debug: Got Block #0020debug: Got Block #0024debug: Got Block #0028debug: Got Block #0032debug: Got Block #0036

will verify ELF image, start= 0x800000, size= 163276

verify sig: 262

Branching to 0x40000

U-Boot 1.2.0 (Tuxbox) (Jul 26 2008 - 21:07:16)

CPU: PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache

*** Warning: CPU Core has Silicon Bugs -- Check the Errata ***

Board: DBOX2, Nokia, BMon V1.0

Watchdog enabled

I2C: ready

DRAM: 32 MB

FLASH: 8 MB

Scanning JFFS2 FS: . . | / . - . \ | / - \ done.

env: found "console"

env: found "lcd_inverse"

env: found "lcd_contrast"

FB: ready

LCD: ready

In: serial

Out: serial

Err: serial

Net: SCC ETHERNET

Options:

1: Console on null

2: Console on ttyS0

3: Console on framebuffer

Select option (1-3), other keys to stop autoboot: 1 0

### FS (squashfs) loading 'vmlinuz' to 0x100000

### FS load complete: 670270 bytes loaded to 0x100000

............................................................... done

Un-Protected 63 sectors

## Booting image at 00100000 ...

Image Name: dbox2

Image Type: PowerPC Linux Kernel Image (gzip compressed)

Data Size: 670206 Bytes = 654.5 kB

Load Address: 00000000

Entry Point: 00000000

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

Linux version 2.4.36.6-dbox2 (image@Server) (gcc version 3.4.6) #8 Sa Jul 26 21:07:50 CEST 2008

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: console=ttyS0,9600 dbox_duplex= root=/dev/mtdblock2 rootfstype=squashfs

Decrementer Frequency = 252000000/60

m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)

m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)

Console: colour dummy device 80x25

Calibrating delay loop... 66.96 BogoMIPS

Memory: 30824k available (1140k kernel code, 344k data, 60k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

squashfs: version 3.0 (2006/03/15) Phillip Lougher

i2c-core.o: i2c core module version 2.6.1 (20010830)

i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)

CPM UART driver version 0.04

ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2

pty: 256 Unix98 ptys configured

half-duplex mode enabled

eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1c:99:2c

loop: loaded (max 8 devices)

D-Box 2 flash driver (size->0x800000 mem->0x10000000)

D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank

Intel/Sharp Extended Query Table at 0x0035

cfi_cmdset_0001: Erase suspend on write enabled

Creating 6 MTD partitions on "D-Box 2 flash memory":

0x00000000-0x00020000 : "BR bootloader"

0x00020000-0x00040000 : "FLFS (U-Boot)"

0x00040000-0x005e0000 : "root (squashfs)"

0x005e0000-0x00800000 : "var (jffs2)"

0x00020000-0x00800000 : "Flash without bootloader"

0x00000000-0x00800000 : "Complete Flash"

Linux video capture interface: v1.00

mice: PS/2 mouse device common for all mice

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 60k init

init started: BusyBox v1.7.2 (2008-07-26 21:12:13 CEST)

##### Image-Version: Keywelt_Jul2008_V1_beta1 #####

Sat Jul 26 21:27:00 UTC 2008

event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $

tuxbox: no IDE-Interface detected

Detected STB:

Vendor: Nokia

Model: D-BOX2

[i2c-8xx]: mpc 8xx i2c init

[i2c-8xx]: adapter: 0

insmod: warning: kernel-module version mismatch

/lib/modules/2.4.36.6-dbox2/misc/dbox2_fp_input.o was compiled for kernel version 2.4.36-dbox2

while this kernel is version 2.4.36.6-dbox2

$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $

$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $

DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).

dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter

$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $

insmod: warning: kernel-module version mismatch

/lib/modules/2.4.36.6-dbox2/misc/avia_av.o was compiled for kernel version 2.4.36-dbox2

while this kernel is version 2.4.36.6-dbox2

avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $

avia_av_core: Starting avia_av_wdt thread.

avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $

avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $

avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $

avia_gt_core: autodetecting chip type... GTX

avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $

avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $

avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $

avia_gt_core: masking unhandled irq reg 1 bit 11

avia_gt_core: masking unhandled irq reg 1 bit 13

avia_gt_ucode: loaded ucode v0014

avia_gt_ucode: ucode section filters disabled.

avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...

avia_gt_core: masking unhandled irq reg 0 bit 6

avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $

avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $

avia_gt_core: Loaded AViA eNX/GTX driver

avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

Console: switching to colour frame buffer device 82x32

avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device

lcd.o: init lcd driver module

lcd.o: found KS0713/SED153X lcd interface

avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $

avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $

avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $

insmod: warning: kernel-module version mismatch

/lib/modules/2.4.36.6-dbox2/misc/ves1820.v12.o was compiled for kernel version 2.4.36-dbox2

while this kernel is version 2.4.36.6-dbox2

DVB: VES1820(0): pwm=0x47 (user specified)

DVB: registering frontend 0:0 (VES1820 based DVB-C frontend)...

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $

avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.264 2008/06/23 09:27:47 seife Exp $

[sectionsd] Caching max 1500 events

[sectionsd] Caching 4 days

[sectionsd] Caching 12 hours Extended Text

[sectionsd] Events are old 120min after their end time

/var/tuxbox/config/zapit/epgfilter.xml: No such file or directory

/var/tuxbox/config/mybouquets.xml: No such file or directory

/var/plugins/operations camd_init

/var/plugins/operations cardserver_start

$Id: zapit.cpp,v 1.410k 2008/04/08 10:00:00 Kroki & Worschter & SnowHead Exp $

[zapit] MAX_SOCKETS=3

[zapit] PMT update enabled

[frontend] uncommitted_switch_mode 0

avia_gt_core: masking unhandled irq reg 0 bit 7

[getservices] /var/tuxbox/config/zapit/myservices.xml found.

/tmp/currentservices.xml: No such file or directory

/var/plugins/operations camd_start

$Id: controld.cpp,v 1.130 2008/01/03 11:09:27 seife Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)

insmod: warning: kernel-module version mismatch

/var/modules/multicam.o was compiled for kernel version 2.4.36-dbox2

while this kernel is version 2.4.36.6-dbox2

[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1DBox2 Multicam Driver v1.01 skars & doz21

[controld] format: 4:3(LB)

starte camd3

/var/plugins/operations check_camd3_socket

[yhttpd] Webserver nhttpd/3.1.8 (yhttpd_core/1.2.0)

[LCDFONT] initializing core...

[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)

[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)

[LCDFONT] adding font /share/fonts/pakenham.ttf...26.07.2008 21:27:28 camd3: BOXTYPE: dbox2

26.07.2008 21:27:28 camd3: LOG: 6

26.07.2008 21:27:28 camd3: UDP_PORT: 20248

26.07.2008 21:27:28 camd3: original slot au on

26.07.2008 21:27:28 camd3: HTTP_PORT: 9080

26.07.2008 21:27:28 camd3: LOG_HOST: 127.0.0.1:514

26.07.2008 21:27:28 camd3: DNS_CACHE: 60 sec

26.07.2008 21:27:28 camd3: DESCR_DELAY: 0 ms

26.07.2008 21:27:28 camd3: camd3.map not found

26.07.2008 21:27:28 camd3: camd3.ignore not found

OK (Pakenham/Regular)

26.07.2008 21:27:28 camd3: original slot: CAID=1722

[LCDFONT] Intializing font cache...

26.07.2008 21:27:28 camd3: UserDB(add): USER=benutzer1 PASS=password2 FROM=any SERVICES=all

26.07.2008 21:27:29 camd3: UserDB(add): USER=benutzer110 PASS=password10 FROM=any SERVICES=1702:000000:0008,1722:000000:0008,

26.07.2008 21:27:29 camd3: UserDB(update): USER=benutzer110 PASS=password10 FROM=any SERVICES=1702:000000:0008,1722:000000:0008,

[yhttpd] Webserver starting...

/var/plugins/operations sect_renice

/var/plugins/operations epg_reinit

neutrino: /lib/libpng12.so.0: no version information available (required by neutrino)

26.07.2008 21:27:39 camd3: KeyDB: started

26.07.2008 21:27:39 camd3: HTTP: started on port 9080

26.07.2008 21:27:41 camd3: Slot /dev/tts/1: (carddetect=password1) initialisiere...

26.07.2008 21:27:41 camd3: Slot /dev/tts/1: starte Monitor...

26.07.2008 21:27:41 camd3: slot /dev/tts/1: ready

starting /bin/neutrino

[neutrino] frameBuffer Instance created

812k video mem

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

[neutrino] Software update enabled

[neutrino] enable flash

26.07.2008 21:27:43 camd3: camd v3.900 b1 - erfolgreich gestartet

[lcdd] time-skin not found -> using default...

[lcdd] weekday-skin not found -> using default...

[lcdd] date-skin not found -> using default...

[lcdd] month-skin not found -> using default...

[LCDFONT] initializing core...

[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)

[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)

[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)

[LCDFONT] Intializing font cache...

[LCDFONT] FTC_Face_Requester (Fix15/Bold)

[LCDFONT] FTC_Face_Requester (Fix14/Bold)

/dev/input/event1: No such file or directory

[neutrino] menue setup

[sectionsd] getUTC: read: Connection timed out

[neutrino] registering as event client

[sectionsd] Request of current/next information for 2713f001c3b5

currentEvt: '' (0000) nextEvt: '' (0000) flag: 0x20

[sectionsd] Request of current/next information for 2713f001c3b5

currentEvt: '' (0000) nextEvt: '' (0000) flag: 0x20

[frontend.cpp:setFrontend:243] ioctl(fd, FE_SET_FRONTEND, feparams): Invalid argument

23:27:50.132 changeDMX [12]-> 0 (0x4e/0xff) (34 seconds)

23:27:50.223 changeDMX [EIT]-> 0 (0x0/0x0) dummy filter (34 seconds)

[neutrino] initialized everything

[sectionsd] Request of current/next information for 3008500de

!myCurrentEvent !myNextEvent currentEvt: '' (0000) nextEvt: '' (0000) flag: 0x28