grosses problem

[Gast timmi]

habe phillips dbox2 sat und microwood image drauf was nicht so gut läuft.möchte das phillips 2*1 draufflashen.aber so bald die box saft bekommt bleibt sie nicht bei ppc boot 1.1.6 stehen sonder ladet alles,wie kommt das und wie bekomme ich das neue image drauf ?

[Gast roni.x]

Hi timmi,

 

lese mal das Readme zum Bootmanager bis zum Ende. Dort steht alles was Du wissen must um das Problem zu lösen :wink:

 

roni.x

 

PS Stichworte sind Halfduplex bzw. Mediasensing

[Gast timmi]

mh komme nicht weiter ist zum haare ausreissen was beim kumpel am montag klappte klappt bei mir nicht und muss neu flashen unbedingt weil 20 mal an und aus bis bild und ton da sind ist unzumutbar.also bitte ich echt um hilfe,und seit nicht böse das ich langen text bei lege vom versuch zu flashen.und problem ist die box fährt währed des flashens normal hoch.

 

avia_gt_dmx: queue_data_move: 1 bytes requested, 0 availibleFlash-FS bootstrap loader (v1.5)

 

Found Flash-FS superblock version 3.1

Found file /root/platform/philips-dbox2/kernel/os in Flash-FS

debug: Got Block #0052

 

will verify ELF image, start= 0x800000, size= 200660

verify sig: 262

Branching to 0x40000

 

 

PPCBoot 1.1.6 (TuxBox) (Nov 16 2002 - 10:23:37)

 

CPU: PPC823ZTnnB2 at 65.900 MHz: 2 kB I-Cache 1 kB D-Cache

Watchdog enabled

Board: DBOX2, Phillips

I2C: ready

DRAM: 32 MB

FLASH: 8 MB

Scanning JFFS2 FS: ........ done.

LCD: ready

FB: loading - ready

In: serial

Out: serial

Err: serial

 

Options:

1: framebuffer on ttyS0

2: framebuffer on fb0

3: framebuffer on null

Select option (1-3), other keys to stop autoboot: 0

...............................................................

Un-Protected 63 sectors

### FS (jffs2) loading 'vmlinuz' to 0x100000

### FS load compleate: 647481 bytes loaded to 0x100000

## Booting image at 00100000 ...

Image Name: dbox2

Image Type: PowerPC Linux Kernel Image (gzip compressed)

Data Size: 647417 Bytes = 632 kB = 0 MB

Load Address: 00000000

Entry Point: 00000000

Verifying Checksum ... OK

Uncompressing Kernel Image ... OK

Linux version 2.4.19 (genial) #12 Sam Nov 16 19:45:12 CET 2002

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: root=/dev/mtdblock/2 rw console=ttyS0

Decrementer Frequency = 247125000/60

mpc8xx-wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)

mpc8xx-wdt: keep-alive trigger activated (PITC: 0x2000)

Console: colour dummy device 80x25

Calibrating delay loop... 65.53 BogoMIPS

Memory: 30820k available (1136k kernel code, 344k data, 68k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12a (20020514) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.1. © 2001, 2002 Red Hat, Inc., designed by Axis Communications

AB.

i2c-core.o: i2c core module

CPM UART driver version 0.03

ttyS00 at 0x0280 is a SMC

ttyS01 at 0x0380 is a SMC

pty: 256 Unix98 ptys configured

eth0: CPM ENET Version 0.2 on SCC2, 00:50:9c:2c:61:75

D-Box 2 flash driver (size->0x800000 mem->0x10000000)

Using word write method

Creating 5 MTD partitions on "D-Box 2 flash memory":

0x00000000-0x00020000 : "BR bootloader"

0x00020000-0x00040000 : "ppcboot (flfs)"

0x00040000-0x00800000 : "root (jffs2)"

0x00020000-0x00800000 : "flash without bootloader"

0x00000000-0x00800000 : "complete flash"

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

jffs2_scan_eraseblock(): Node at 0x0026e08c {0x1985, 0xe002, 0x00000051) has inv

alid CRC 0x1985c002 (calculated 0xc932c6d5)

VFS: Mounted root (jffs2 filesystem).

Mounted devfs on /dev

Freeing unused kernel memory: 68k init

init started: BusyBox v0.61.pre (2002.09.22-12:09+0000) multi-caUsing /lib/modu

les/2.4.19/misc/i2c-8xx.o

[i2c-8xx]: mpc 8xx i2c init

i2c-core.o: adapter registered as adapter 0.

[i2c-8xx]: adapter: 0

Using /lib/modules/2.4.19/misc/info.o

Using /lib/modules/2.4.19/kernel/drivers/input/input.o

Using /lib/modules/2.4.19/kernel/drivers/input/evdev.o

Using /lib/modules/2.4.19/misc/event.o

event: init ...

Using /lib/modules/2.4.19/misc/saa7126.o

i2c-core.o: driver i2c saa7126 driver registered.

i2c-core.o: client [i2c saa7126 chip] registered to adapter [](pos. 0).

Using /lib/modules/2.4.19/misc/avs.o

i2c-core.o: driver i2c audio/video switch driver registered.

i2c-core.o: client [sTV6412] registered to adapter [](pos. 1).

Using /lib/modules/2.4.19/misc/fp.o

i2c-core.o: driver DBox2 Frontprocessor driver registered.

i2c-core.o: client [DBox2 Frontprocessor client] registered to adapter [](pos. 2

).

fp.o: clear_wakeup_timer [0][0]

Using /lib/modules/2.4.19/misc/dvb_demux.o

Using /lib/modules/2.4.19/misc/dvbdev.o

Using /lib/modules/2.4.19/misc/avia.o

Using /lib/modules/2.4.19/misc/dmxdev.o

Using /lib/modules/2.4.19/misc/cam.o

AVIA: $Id: avia_core.c,v 1.32 2002/09/24 17:50:19 Jolt Exp $

der moment ist gekommen...

Using /lib/modules/2.4.19/misc/dvb_frontend.o

i2c-core.o: driver DBox2-CAM registered.

CAM: attaching CAM at 0x6e

i2c-core.o: client [DBOX2-CAM] registered to adapter [](pos. 3).

CAM: attached to adapter

Using /lib/modules/2.4.19/misc/lcd.o

lcd.o: init lcd driver module

lcd.o: found KS0713/SED153X lcd interface on 2

write 1 event's ...

initializing core...

adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)

Intializing font cache...

Using /lib/modules/2.4.19/misc/avia_gt.o

avia_gt_core: $Id: avia_gt_core.c,v 1.23 2002/10/05 15:01:12 Jolt Exp $

avia_gt_core: autodetecting chip type... AViA eNX found

avia_gt_enx: $Id: avia_gt_enx.c,v 1.13 2002/09/02 19:25:37 Jolt Exp $

avia_gt_accel: $Id: avia_gt_accel.c,v 1.8 2002/10/13 21:16:15 Jolt Exp $

avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.134 2002/09/21 00:00:08 Jolt Exp $

avia_gt_dmx: Successfully loaded ucode V0.14

ENX-INITed -> 0

there MIGHT be no TS

avia_gt_dmx: warning, misaligned queue 0 (is 0x32A00, size 65536), aligning...

avia_gt_gv: $Id: avia_gt_gv.c,v 1.25 2002/10/11 09:57:54 Jolt Exp $

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.19 2002/10/03 11:12:42 thegoodguy Exp $

avia_gt_capture: $Id: avia_gt_capture.c,v 1.22 2002/08/22 13:39:33 Jolt Exp $

avia_gt_pig: $Id: avia_gt_pig.c,v 1.28 2002/08/22 13:39:33 Jolt Exp $

avia_gt_ir: $Id: avia_gt_ir.c,v 1.19 2002/08/22 13:39:33 Jolt Exp $

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.17 2002/10/05 15:01:12 Jolt Exp $

avia_gt_core: Loaded AViA eNX/GTX driver

Using /lib/modules/2.4.19/misc/dvb.o

Using /lib/modules/2.4.19/misc/dvb.o

insmod: A module named dvb already exists

Init TDA8044H

Using /lib/modules/2.4.19/misc/tda8044h.o

i2c-core.o: driver TDA8044H DVB DECODER registered.

tda8044h.c: attaching TDA8044H at 0xd0

i2c-core.o: client [TDA8044H] registered to adapter [](pos. 4).

Using /lib/modules/2.4.19/misc/avia_gt_napi.o

avia_gt_napi: $Id: avia_gt_napi.c,v 1.130 2002/09/18 15:57:24 Jolt Exp $

avia_gt_napi: hardware section filtering disabled.

Using /lib/modules/2.4.19/misc/avia_gt_vbi.o

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.16 2002/08/22 13:39:33 Jolt Exp $

avia_gt_vbi: got demux C-Cube - AViA eNX/GTX

Using /lib/modules/2.4.19/misc/avia_gt_fb.o

avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.36 2002/08/22 13:39:33 Jolt Exp $

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

Console: switching to colour frame buffer device 82x32

avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device

Using /lib/modules/2.4.19/misc/avia_gt_proc.o

avia_gt_proc: $Id: avia_gt_proc.c,v 0.7 2002/10/12 13:38:30 NoClue $

cdkVcInfo $Id: cdkVcInfo.c,v 1.0 2002/09/26 20:48:26 alexW Exp $

 

[CBasicClient] connect failed.

/tmp/sectionsd.sock: No such file or directory

$Id: sectionsd.cpp,v 1.139 2002/10/15 20:39:47 woglinde Exp $

caching 72 hours

events are old 60min after their end time

[camd] 1.CMD-Class 0xE0

[camd] no card is in slot #2

[camd] no card is in slot #1

[camd] ca system id: 1702

$Id: zapit.cpp,v 1.268 2002/10/28 22:47:21 thegoodguy Exp $

 

[zapit] Using /bin/emu/camd for Emu mode.

[camd] no card is in slot #2

[camd] no card is in slot #1

[getservices.cpp] going to parse satellite Astra 19.2E

[getservices.cpp] going to parse satellite Eutelsat 13.0E

[zapit] LoadServices: success

[zapit] reading Bouquets .......................................................

................................................................................

......

[zapit] Found 141 bouquets.

[zapit] channels have been loaded succesfully

[nhttpd] Neutrino HTTP-Server starting..

killall: aniplay: no process killed

Network LCD-Driver $Id: lcdd.cpp,v 1.57 2002/10/17 10:16:35 thegoodguy Exp $

 

[lcdd] time-skin not found -> using default...

[lcdd] weekday-skin not found -> using default...

[lcdd] date-skin not found -> using default...

[lcdd] month-skin not found -> using default...

[lcdd] load config

initializing core...

adding font /share/fonts/micron.ttf...OK (Micron/Regular)

Intializing font cache...

FTC_Face_Requester (Micron/Regular)

Controld $Id: controld.cpp,v 1.78 2002/11/05 19:47:21 obi Exp $

 

[controld] Boxtype detected: (02, 2, 3, Philips)

set event: 00000009

[controld] Unknown aspectRatio: 0[controld] setting VideoFormat to auto

[neutrino] NeutrinoNG $Id: neutrino.cpp,v 1.344 2002/10/16 16:25:24 gbox-Version

Exp $

 

[neutrino] New Options : neutrino [-key] (Keyeditor) [-gbox] (gboxMenu) [-cug] (

Keyeditor+gboxMenu)

[neutrino] frameBuffer Instance created

[neutrino] vcrControl Instance created

1024k video mem

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

[neutrino] enable flash

[neutrino] Software update enabled

[neutrino] gbox Menu / gbox Info / Keyedit Feature enabled !

IP : 192.168.0.2

Netmask : 255.255.255.0

Broadcast: 192.168.0.255

Gateway : 192.168.0.1

[neutrino] menue setup

[CHTTPUpdater] HTTP-Basepath:

[CHTTPUpdater] Image-Filename: cdk.cramfs

[CHTTPUpdater] Version-Filename: cdk.cramfs.version

loading locales: scandir: No such file or directory

[controld] setting VideoFormat to auto

video notify: videomenu.videoformat

[neutrino] control event register

[neutrino] sectionsd event register

[neutrino] zapit event register

[neutrino] timerd event register

[CFrontend::setFrontend] freq 1548500

[CFrontend::getEvent] FE_COMPLETION_EV: freq 1548500

use not card

[zapit] starting emu program

[CPlugins] Dir: /lib/tuxbox/plugins/

 

 

gbox version v0.896 (beta version)

mode: any pid

OSD (dbox2) IP = 192.168.0.2

AU:01/update:01/KeyFile:00 Hash:00 DispECM:00/EMM:00 UDPInit:01 OSD:02

[CPlugins] 12 plugins found...

*ECM: CA ID: 0x1702 Betacrypt PW -> CA PID: 0x1035

*ECM: CA ID: 0x1762 Betacrypt PW -> CA PID: 0x1835

**** hashTableECM 2 elements ****

Logger init for IP: 192.168.110.225=< on port 8017

avia_gt_dmx: reloading stc

*EMM: CA ID: 0x1702 Betacrypt PW -> CA PID: 0x1000

*EMM: CA ID: 0x1762 Betacrypt PW -> CA PID: 0x0258

**** hashTableEMM 2 elements ****

detected EMM data on pid 0258 - Betacrypt

detected EMM data on pid 1000 - Betacrypt

avia_gt_dmx: queue_data_move: -20 bytes requested, 109 availible

avia_gt_dmx: queue_data_move: 1 bytes requested, 0 availible

avia_gt_dmx: queue_data_move: 255 bytes requested, 115 availible

avia_gt_dmx: queue_data_move: 1 bytes requested, 0 availible

avia_gt_dmx: queue_data_move: -144 bytes requested, 0 availible

avia_gt_dmx: queue_data_move: 1 bytes requested, 0 availible

[sectionsd] read: Success

avia_gt_dmx: queue_data_move: 255 bytes requested, 115 availible

 

avia_gt_dmx: queue_data_move: -144 bytes requested, 0 availible

avia_gt_dmx: queue_data_move: 1 bytes requested, 0 availible

 

 

 

 

 

 

und bei pinging dbox2 steht ok und in klammern 1ms [/img]

[Gast timmi]

so jungs hat sich erledigt,mein dummer fehler war es.

[Gast peacekeeper]

Hi,

 

um das und microwood image zu löschen, führst du am besten einen Flash Reset aus, dann kannst du jedes Image neu Flashen.

Hatte auch das Problem, das die Box durchläuft aber nach dem Reset geht es wieder.