jockelb Geschrieben 6. Juni 2012 Melden Share Geschrieben 6. Juni 2012 Hi ich habe mir eine neue Coolstream neo2 geholt. Mit dem orginal Image blieb die Box immer bei der Sendersuche hängen. Da hab ich noch gedacht es ist eine Software problem. Daher hab ich mich entschlossen das Keywelt Image zu flashen. Jetzt blieb die Box nicht mehr bei der Sendersuche hängen , sondern erst nach 1 Sekunde Ton von ARD Bild kam nie. Daraufhin hab ich nach der Rep Anleitung hier die Box mit Nullmodemkabel neu geflasht mtd2 und mtd3. Nun bleibt die Box bei starte Neutrino hängen. Brauche ich andere img Dateien für die neo2? Welche? Danke Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
deSterne Geschrieben 9. Juni 2012 Melden Share Geschrieben 9. Juni 2012 Hi jockelb, bei der Neo² hat bei mir folgender Thread geholfen http://www.keywelt-board.com/index.php?/topic/163542-notfallwiederherstellung-ohne-nullmodemkabel-neo/ Funktioniert ohne Nullmodemkabel, etc. nur USB Stick mit den richtigen Dateien in den Front USB Anschluss und beim Starten im richtigen Moment 2x den Power Knopf drücken. Gruß desterne Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
jockelb Geschrieben 13. Juni 2012 Autor Melden Share Geschrieben 13. Juni 2012 (bearbeitet) Die Dateien findet man bei Google NEVER USE NOT OFICIAL SOFTWARE, OR YOU DO IT ON YOUR OWN RISK Coolstream Emergency Tool for Neo --------------------------------- To Upgrade your Coolstream receiver please copy kernel.img (kernel) and sysroot.img (filesystem) on USB STICK (must be FAT32 Formated). Insert USB STICK in Coolstream USB Port(front), connect serial Cable between PC and Coolstream STB, and start the program on your Windows PC following the Instructions to update Kernel and/or Filesystem. After the tool recognise your Coolstream please wait few seconds bevore push the button for kernel or filesys update. Note: If the Update doesnt succeed just change to another USB STICK, maybe this one you have is not supported by our bootloader! Or if you use some usb to serial Cable the communication in windows may disturbed, so remove and insert it again. Manual Update ------------- You can flash over serial direct from bootloader, set your serial port to 115 200 baud and press enter after power up, you will get a prompt from the bootloader (dont forget to insert the usb stick with needed files): Hdx> there you have to use this command according to what you need to flash. Kernel update: ------------- HDx>usb start HDx>fatload usb 0 0x0E000000 kernel.img reading kernel.img ......................................................................................................................................................................................................... 2060560 bytes read HDx>erase 0xF0080000 +0x00400000 ................................ Erased 32 sectors HDx>cp.b 0x0E000000 0xF0080000 0x00400000 Copy to Flash... ................................ done HDx>re to reset STB Filesystem Update: ------------------ HDx> usb start (Re)start USB... USB: ehci_hcd_init(); CX2450x init hccr e8000100 and hcor e8000140 hc_length 64 Register 10011 NbrPorts 1 USB EHCI 1.00 scanning bus for devices... 2 USB Device(s) found scanning bus for storage devices... 1 Storage Device(s) found HDx> fatload usb 0 0x0E000000 sysroot.img reading sysroot.img . ................................................................................ .............................................................. 19239496 bytes read <-----here we must calculate and convert to HEX value, for example 23601412 / 4 = 5A0841 HDx> erase 0xF0480000 0xF1FFFFFF ................................................................................ ................................................................................ Erased 220 sectors HDx> cp 0x0E000000 0xF0480000 0x5A0841 Copy to Flash... ............................................................... ...................................................... done HDx> re bearbeitet 13. Juni 2012 von Gandal Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
jockelb Geschrieben 13. Juni 2012 Autor Melden Share Geschrieben 13. Juni 2012 Zum Umrechnen der Dezimalzahlen http://www.arndt-bruenner.de/mathe/scripts/Zahlensysteme.htm Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Admin Gandalf Geschrieben 13. Juni 2012 Admin Melden Share Geschrieben 13. Juni 2012 Zum Umrechnen der Dezimalzahlen http://www.arndt-bru...hlensysteme.htm Das macht auch der Windowsrechner, musst nur umschalten nach der Eingabe im richtigen Zahlensystem Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Empfohlene Beiträge