Jump to content

SD-Card wird nicht erkannt

blomber

Von blomber
in Das Keywelt-Image

Empfohlene Beiträge

blomber

blomber

Geschrieben
Geschrieben

moin jungs.

irgendwie will meine sd-karte nicht an gang kommen.

kenn mich da so gar nicht aus, da wir erst bis heute morgen 04:20 gelötet haben.

hab hier mal nen bootlog. vielleicht kann ja einer von euch helfen:

 

WATCHDOG reset enabled

dbox2:root> debug:

BOOTP/TFTP bootstrap loader (v0.3)

debug:

debug: Transmitting BOOTP request via broadcast

debug: Given up BOOTP/TFTP boot

boot net failed

 

Flash-FS bootstrap loader (v1.5)

 

Found Flash-FS superblock version 3.1

Found file /root/platform/sagem-dbox2/kernel/os in Flash-FS

debug: Got Block #0040

 

will verify ELF image, start= 0x800000, size= 162920

verify sig: 262

Branching to 0x40000

 

 

U-Boot 1.2.0 (Tuxbox) (Jul 26 2007 - 19:52:45)

 

CPU:   PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache

Board: DBOX2, Sagem, BMon V1.2

       Watchdog enabled

I2C:   ready

DRAM:  32 MB

FLASH:  8 MB

Scanning JFFS2 FS: ..... done.

FB:    ready

LCD:   ready

In:    serial

Out:   serial

Err:   serial

Net:   SCC ETHERNET

 

Options:

  1: Console on null

  2: Console on ttyS0

  3: Console on framebuffer

Select option (1-3), other keys to stop autoboot:  0

### FS (squashfs) loading 'vmlinuz' to 0x100000

### FS load complete: 696870 bytes loaded to 0x100000

............................................................... done

Un-Protected 63 sectors

## Booting image at 00100000 ...

   Image Name:   dbox2

   Image Type:   PowerPC Linux Kernel Image (gzip compressed)

   Data Size:    696806 Bytes = 680.5 kB

   Load Address: 00000000

   Entry Point:  00000000

   Verifying Checksum ... OK

   Uncompressing Kernel Image ... OK

Linux version 2.4.32-dbox2 (stachi@linux) (gcc version 3.4.4) #1 Do Jul 26 18:24

:52 CEST 2007

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs

Decrementer Frequency = 247500000/60

m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)

m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)

Console: colour dummy device 80x25

Calibrating delay loop... 65.74 BogoMIPS

Memory: 30740k available (1184k kernel code, 384k data, 60k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc.

squashfs: version 3.0 (2006/03/15) Phillip Lougher

i2c-core.o: i2c core module version 2.6.1 (20010830)

i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)

CPM UART driver version 0.04

ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2

pty: 256 Unix98 ptys configured

eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:32:27:2b

loop: loaded (max 8 devices)

D-Box 2 flash driver (size->0x800000 mem->0x10000000)

D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank

Intel/Sharp Extended Query Table at 0x0031

Using buffer write method

cfi_cmdset_0001: Erase suspend on write enabled

Creating 6 MTD partitions on "D-Box 2 flash memory":

0x00000000-0x00020000 : "BR bootloader"

0x00020000-0x00540000 : "root (squashfs)"

0x00540000-0x007e0000 : "var (jffs2)"

0x007e0000-0x00800000 : "FLFS (U-BOOT)"

0x00020000-0x00800000 : "Flash without bootloader"

0x00000000-0x00800000 : "Complete Flash"

Linux video capture interface: v1.00

mice: PS/2 mouse device common for all mice

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 60k init

init started:  BusyBox v1.2.1 (2007.08.05-21:58+0000) multi-call

 

##### Image-Version: Keywelt_Sep2006_V2_hdd_beta7 #####

 

$Id: mmccombo.c TESTVERSION 2007/05/27 18:58 satsuse Exp $

mmc: force hardware allocation, even if otherwise assigned.

mmc: Hardware init for wiringopt = 2 - FORCED! But A:C0 B:0

mmc: used wiringopt = 2

mmc: trying to reset card ...

mmc: ... failed.

mmc: error in mmc_card_init (0)

mmc: error in mmc_init (-1)

mmccombo               13880   0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo               13880   0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo               13880   0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo               13880   0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo               13880   0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

## sdmmc Treiber /var/modules/mmccombo.o wiringopt=2 opt=1 forcehw=1 fehlerhaft

##

Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4

ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx

dboxide: $Id: main.c,v 1.9 2006/09/11 17:30:00 carjay Exp $

ide: late registration of driver.

dboxide: activating cs2

dboxide: address space of DBox2 IDE CPLD is at: 0xc38ad000

Probing IDE interface ide0...

hda: SAMSUNG SP1654N, ATA DISK drive

ide0 at 0x010-0x017,0x04e on irq 12

hda: attached ide-disk driver.

hda: host protected area => 1

warte auf init_ide

warte auf init_ide

hda: 312581808 sectors (160042 MB) w/8192KiB Cache, CHS=19457/255/63

Partition check:

/dev/ide/host0/bus0/target0/lun0: p1 p2

warte auf init_ide

EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended

 

/dev/ide/host0/bus0/target0/lun0/disc:

setting acoustic management to 128

setting drive write-caching to 0 (off)

setting standby to 72 (6 minutes)

write-caching =  1 (on)

acoustic      = 128 (128=quiet ... 254=fast)

init_ide fertig

event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $

Detected STB:

  Vendor: Sagem

  Model: D-BOX2

[i2c-8xx]: mpc 8xx i2c init

[i2c-8xx]: adapter: 0

$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $

$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $

DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).

dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter

$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $

avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $

avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $

avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $

avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $

avia_gt_core: autodetecting chip type... eNX

avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $

avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $

avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $

avia_gt_ucode: loaded ucode v0014

avia_gt_ucode: ucode section filters disabled.

avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...

avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $

avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $

avia_gt_core: Loaded AViA eNX/GTX driver

avia_av_core: Starting avia_gt_wdt thread.

avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

Console: switching to colour frame buffer device 82x32

avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device

lcd.o: init lcd driver module

lcd.o: found KS0713/SED153X lcd interface

avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $

avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $

avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $

insmod: Warning: kernel-module version mismatch

        /var/modules/at76c651.o was compiled for kernel version 2.4.34-dbox2

        while this kernel is version 2.4.32-dbox2

DVB: registering frontend 0:0 (VES1993)...

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $

avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $

avia_gt_proc: $Id: avia_gt_proc.c, v 0.1.3 2005/12/11 22:30:00 Skars & Merandos

Exp $

avia_gt_proc: Description: GTX/ENX proc_dev Driver with proc_fs extension

options:

(demux reinit)  enx_reset=1

(framer chan.)  fc_reset=1

(clr avia reg)  avia=0

(enx td trace)  trace=1

(lock, unlock)  spinlock=0

Schreiben ueber /proc/bus/gtx

(delay)         delay=500

Thu Jan  1 01:00:00 CET 1970

 

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.227 2006/06/

08 20:19:32 houdini Exp $

[sectionsd] Caching max 3000 events

[sectionsd] Caching 14 days

[sectionsd] Events are old 60min after their end time

/var/plugins/operations logcs_init

/var/plugins/operations camd_init

/var/plugins/operations cardserver_start

$Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 Kroki & Worschter Exp $

[zapit] MAX_SOCKETS=3

/var/plugins/operations camd_start

starte mgcamd

[getservices] /var/tuxbox/config/zapit/myservices.xml  found.

[getservices] dup transponder id 3 onid 85

[getservices] dup transponder id 11 onid 85

[getservices] dup transponder id 2 onid 85

[getservices] dup transponder id 4 onid 85

[getservices] dup transponder id 1 onid 85

tuxbox mgcamd v1.24 by mixvt (compiled Jun 17 2007 22:38:37)

[mg] Net:4:7:1:10s Show ecm:1, emm:1 Up:1 Au:2 Dir:0 Osd:no:80:0 Cache:7 Log:2:1

72.16.1.1:28007 Reread:0

[mg] Ecm cache time: 15

Box type: dbox2

Conax.Key error 2: No such file or directory

Keys readed

Conax.Key error 2: No such file or directory

[mgcam] emm thread started

[mgcamd] tps update started.

/tmp/currentservices.xml: No such file or directory

$Id: controld.cpp,v 1.124 2006/06/27 10:21:59 barf Exp $

 

[controld] Boxtype detected: (3, Sagem D-BOX2)

[controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1

[yhttpd] Webserver nhttpd/3.1.2 (yhttpd_core/1.2.0)

[LCDFONT] initializing core...

[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)

[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)

[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)

[LCDFONT] Intializing font cache...

[basicsocket] send_data: Resource temporarily unavailable

[basicsocket] send_data: Resource temporarily unavailable

[yhttpd] Webserver starting...

/var/plugins/operations epg_reinit

neutrino: /lib/libpng12.so.0: no version information available (required by neut

rino)

[neutrino] frameBuffer Instance created

812k video mem

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

[neutrino] Software update enabled

[neutrino] enable flash

[lcdd] time-skin not found -> using default...

[sectionsd] getUTC: read: Connection timed out

[lcdd] weekday-skin not found -> using default...

[lcdd] date-skin not found -> using default...

[lcdd] month-skin not found -> using default...

[LCDFONT] initializing core...

[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)

[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)

[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)

[LCDFONT] Intializing font cache...

[LCDFONT] FTC_Face_Requester (Fix15/Bold)

[LCDFONT] FTC_Face_Requester (Fix14/Bold)

/dev/input/event1: No such file or directory

[neutrino] menue setup

[neutrino] received 43 sats

[neutrino] registering as event client

[basicsocket] send_data: Resource temporarily unavailable

[neutrino] initialized everything

zap failed!

Link zu diesem Kommentar
Auf anderen Seiten teilen
blomber

blomber

Geschrieben
  • Autor
Geschrieben

hier mal der bootlog mit mmc-treiber auf auto. mit der agfa s-karte 1GB:

 

CPU:  PPC823ZTnnB2 at 66 MHz: 2 kB I-Cache 1 kB D-Cache

Board: DBOX2, Sagem, BMon V1.2

      Watchdog enabled

I2C:  ready

DRAM:  32 MB

FLASH:  8 MB

Scanning JFFS2 FS: .... done.

FB:    ready

LCD:  ready

In:    serial

Out:  serial

Err:  serial

Net:  SCC ETHERNET

 

Options:

  1: Console on null

  2: Console on ttyS0

  3: Console on framebuffer

Select option (1-3), other keys to stop autoboot:  0

### FS (squashfs) loading 'vmlinuz' to 0x100000

### FS load complete: 696870 bytes loaded to 0x100000

............................................................... done

Un-Protected 63 sectors

## Booting image at 00100000 ...

  Image Name:  dbox2

  Image Type:  PowerPC Linux Kernel Image (gzip compressed)

  Data Size:    696806 Bytes = 680.5 kB

  Load Address: 00000000

  Entry Point:  00000000

  Verifying Checksum ... OK

  Uncompressing Kernel Image ... OK

Linux version 2.4.32-dbox2 (stachi@linux) (gcc version 3.4.4) #1 Do Jul 26 18:24

:52 CEST 2007

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs

Decrementer Frequency = 247500000/60

m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)

m8xx_wdt: keep-alive trigger installed (PITC: 0x2000)

Console: colour dummy device 80x25

Calibrating delay loop... 65.53 BogoMIPS

Memory: 30740k available (1184k kernel code, 384k data, 60k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc.

squashfs: version 3.0 (2006/03/15) Phillip Lougher

i2c-core.o: i2c core module version 2.6.1 (20010830)

i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)

CPM UART driver version 0.04

ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2

pty: 256 Unix98 ptys configured

eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:32:27:2b

loop: loaded (max 8 devices)

D-Box 2 flash driver (size->0x800000 mem->0x10000000)

D-Box 2 flash memory: Found 1 x16 devices at 0x0 in 16-bit bank

Intel/Sharp Extended Query Table at 0x0031

Using buffer write method

cfi_cmdset_0001: Erase suspend on write enabled

Creating 6 MTD partitions on "D-Box 2 flash memory":

0x00000000-0x00020000 : "BR bootloader"

0x00020000-0x00540000 : "root (squashfs)"

0x00540000-0x007e0000 : "var (jffs2)"

0x007e0000-0x00800000 : "FLFS (U-BOOT)"

0x00020000-0x00800000 : "Flash without bootloader"

0x00000000-0x00800000 : "Complete Flash"

Linux video capture interface: v1.00

mice: PS/2 mouse device common for all mice

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 60k init

init started:  BusyBox v1.2.1 (2007.08.05-21:58+0000) multi-call

 

##### Image-Version: Keywelt_Sep2006_V2_hdd_beta7 #####

 

$Id: mmccombo.c TESTVERSION 2007/05/27 18:58 satsuse Exp $

mmc: force hardware allocation, even if otherwise assigned.

mmc: User asked for autodetection, I'll try ...

mmc: Hardware init for wiringopt = 4 - OK

mmc: trying to reset card ...

mmc: ... failed.

mmc: Hardware cleanup - done

mmc: Hardware init for wiringopt = 1 - OK

mmc: trying to reset card ...

mmc: ... failed.

mmc: Hardware cleanup - done

mmc: Hardware init for wiringopt = 2 - FORCED! But A:C0 B:0

mmc: trying to reset card ...

mmc: Card init *OK1*

mmc: Card init *OK2*

mmc: used wiringopt = 2

mmc: error in mmc_card_config (1)

mmc: error in mmc_init (-1)

mmccombo              13880  0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo              13880  0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo              13880  0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo              13880  0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

mmccombo              13880  0 (unused)

rmmod: /var/modules/mmccombo: No such file or directory

insmod: A module named mmccombo already exists

## sdmmc Treiber /var/modules/mmccombo.o wiringopt=0 opt=1 forcehw=1 fehlerhaft

##

Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4

ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx

dboxide: $Id: main.c,v 1.9 2006/09/11 17:30:00 carjay Exp $

ide: late registration of driver.

dboxide: activating cs2

dboxide: address space of DBox2 IDE CPLD is at: 0xc38ad000

Probing IDE interface ide0...

hda: SAMSUNG SP1654N, ATA DISK drive

ide0 at 0x010-0x017,0x04e on irq 12

hda: attached ide-disk driver.

hda: host protected area => 1

warte auf init_ide

warte auf init_ide

hda: 312581808 sectors (160042 MB) w/8192KiB Cache, CHS=19457/255/63

Partition check:

/dev/ide/host0/bus0/target0/lun0: p1 p2

warte auf init_ide

EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended

 

/dev/ide/host0/bus0/target0/lun0/disc:

setting acoustic management to 128

setting drive write-caching to 0 (off)

setting standby to 72 (6 minutes)

write-caching =  1 (on)

acoustic      = 128 (128=quiet ... 254=fast)

init_ide fertig

event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $

Detected STB:

  Vendor: Sagem

  Model: D-BOX2

[i2c-8xx]: mpc 8xx i2c init

[i2c-8xx]: adapter: 0

$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $

$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $

DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).

dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter

$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $

avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $

avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $

avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $

avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $

avia_gt_core: autodetecting chip type... eNX

avia_gt_enx: $Id: avia_gt_enx.c,v 1.21 2003/09/30 05:45:35 obi Exp $

avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $

avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $

avia_gt_ucode: loaded ucode v0014

avia_gt_ucode: ucode section filters disabled.

avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...

avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $

avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $

avia_gt_core: Loaded AViA eNX/GTX driver

avia_av_core: Starting avia_gt_wdt thread.

avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

Console: switching to colour frame buffer device 82x32

avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device

lcd.o: init lcd driver module

lcd.o: found KS0713/SED153X lcd interface

avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $

avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $

avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $

DVB: registering frontend 0:0 (VES1993)...

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $

avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $

avia_gt_proc: $Id: avia_gt_proc.c, v 0.1.3 2005/12/11 22:30:00 Skars & Merandos

Exp $

avia_gt_proc: Description: GTX/ENX proc_dev Driver with proc_fs extension

options:

(demux reinit)  enx_reset=1

(framer chan.)  fc_reset=1

(clr avia reg)  avia=0

(enx td trace)  trace=1

(lock, unlock)  spinlock=0

Schreiben ueber /proc/bus/gtx

(delay)        delay=500

Thu Jan  1 01:00:00 CET 1970

 

Please press Enter to activate this console. $Id: sectionsd.cpp,v 1.227 2006/06/

08 20:19:32 houdini Exp $

[sectionsd] Caching max 3000 events

[sectionsd] Caching 14 days

[sectionsd] Events are old 60min after their end time

/var/plugins/operations logcs_init

/var/plugins/operations camd_init

/var/plugins/operations cardserver_start

$Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 Kroki & Worschter Exp $

[zapit] MAX_SOCKETS=3

[zapit] PMT update enabled

/var/plugins/operations camd_start

DBox2 Multicam Driver v1.01 skars & doz21 ;)

starte camd3

/var/plugins/operations check_camd3_socket

01.01.1970 01:00:15 camd3: BOXTYPE:  1

01.01.1970 01:00:15 camd3: LOG:  6

01.01.1970 01:00:15 camd3: UDP_PORT:  20248

01.01.1970 01:00:15 camd3: original slot au on

01.01.1970 01:00:15 camd3: HTTP_PORT:  9080

01.01.1970 01:00:16 camd3: LOG_HOST:  127.0.0.1:514

01.01.1970 01:00:16 camd3: DNS_CACHE:  600 sec

01.01.1970 01:00:16 camd3: SOCKET:  /tmp/camd.sock01

01.01.1970 01:00:16 camd3: KEYS:    /var/keys/camd3.keys

01.01.1970 01:00:16 camd3: SERVERS:  /var/keys/camd3.servers

01.01.1970 01:00:16 camd3: USERS:  /var/keys/camd3.users

01.01.1970 01:00:16 camd3: Slot /dev/tts/1: (carddetect=password1) initialisiere

...

[getservices] /var/tuxbox/config/zapit/myservices.xml  found.

[getservices] dup transponder id 3 onid 85

[getservices] dup transponder id 11 onid 85

[getservices] dup transponder id 2 onid 85

[getservices] dup transponder id 4 onid 85

[getservices] dup transponder id 1 onid 85

01.01.1970 01:00:17 camd3: Slot /dev/tts/1: starte Monitor...

01.01.1970 01:00:17 camd3: Slot /dev/tts/1: bereit

01.01.1970 01:00:17 camd3: /var/keys/camd3.keys No such file or directory

01.01.1970 01:00:17 camd3: KeyDB: gestartet

01.01.1970 01:00:17 camd3: original slot: CAID=1702

 

01.01.1970 01:00:17 camd3: camd v3.868 - erfolgreich gestartet

01.01.1970 01:00:17 camd3: HTTP: started on port 9080

/tmp/currentservices.xml: No such file or directory

$Id: controld.cpp,v 1.124 2006/06/27 10:21:59 barf Exp $

 

[controld] Boxtype detected: (3, Sagem D-BOX2)

[controld]: ROUTEVIDEO v1 = 0 a1 = 0 v2 = 0 a2 = 0 fblk=1

[yhttpd] Webserver nhttpd/3.1.2 (yhttpd_core/1.2.0)

[LCDFONT] initializing core...

[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)

[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)

[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)

[LCDFONT] Intializing font cache...

[basicsocket] send_data: Resource temporarily unavailable

[basicsocket] send_data: Resource temporarily unavailable

[yhttpd] Webserver starting...

/var/plugins/operations epg_reinit

neutrino: /lib/libpng12.so.0: no version information available (required by neut

rino)

[sectionsd] getUTC: read: Connection timed out

[neutrino] frameBuffer Instance created

812k video mem

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

[neutrino] Software update enabled

[neutrino] enable flash

[lcdd] time-skin not found -> using default...

[lcdd] weekday-skin not found -> using default...

[lcdd] date-skin not found -> using default...

[lcdd] month-skin not found -> using default...

[LCDFONT] initializing core...

[LCDFONT] adding font /share/fonts/12.pcf.gz...OK (Fix12/Regular)

[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)

[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)

[LCDFONT] Intializing font cache...

[LCDFONT] FTC_Face_Requester (Fix15/Bold)

[LCDFONT] FTC_Face_Requester (Fix14/Bold)

/dev/input/event1: No such file or directory

[neutrino] menue setup

[neutrino] received 43 sats

[neutrino] registering as event client

[basicsocket] send_data: Resource temporarily unavailable

[basicsocket] send_data: Resource temporarily unavailable

[neutrino] initialized everything

Link zu diesem Kommentar
Auf anderen Seiten teilen
caladon

caladon

Geschrieben
Geschrieben

Moin, moin.

 

Gut, aber da wird der Modemport dann ja auch nicht ausschließlich von der SD benutzt. Wird dann trotzdem der mmc2 benutzt und nicht der mmc1??????

Sorry hab mich mangels IDE-IF noch nicht damit beschäftigt .... aber Ende KW34 soll es eintreffen ;)B)B) deshalb würde mich die Info auch interessieren! ;)

Link zu diesem Kommentar
Auf anderen Seiten teilen
stachi

stachi

Geschrieben
Geschrieben

IDE-Interface und Karte laufen zusammen am Modemport ;)

Es ist egal ob SD oder MMC

alles bis 1GB sollte ohne Probleme laufen

aber es kann nie schaden eine kleinere Karte zu testen denn manche Karten mögen die Box nicht

ich würde dir Empfelen in einer Sagem die andere Verkebelung zu Testen (ist doppelt so schnell)

wenn du die PDF-Anleitung hast, hast du dran gedacht PIN 1 und 5 zu vertauschen Klick

Link zu diesem Kommentar
Auf anderen Seiten teilen
blomber

blomber

Geschrieben
  • Autor
Geschrieben

habs nach mmc2 vom powerboard gemacht.

 

hab das ganze nochmal ausgebaut und komplett durchgemessen.

- alle verbindungen gehen durch

- alle pins sind korrekt belegt

- die brücke zwischen 3 und 6 steht und steuert auch durch

- der widerstand 100kohm funktioniert in beide richtungen mit 100kohm (fantastisch)

- kein kurzschluss messbar

- die karten (habe mitlerweile mehrere probiert) haben kontakt zur aufnahme (sieht man an den schleifspuren auf den kontakten /habe nach anleitung hier aus dem board mit nen 5,25 zoll floppy-kabel das interface gebaut)

 

was ich mir noch vorstellen könnte: sind vielleicht die kabel zu lang? habe runde vieradrige laufwerkskabel genommen um alles steckbar zu machen. aber wie gesagt. signale gehen durch.

 

oder es liegt doch an den karten. habe 256 MB extreMEmory mmc-card, 256 MB Medion multi media card und Agfa Photo sd 1GB memory card

ausprobiert

Link zu diesem Kommentar
Auf anderen Seiten teilen
stachi

stachi

Geschrieben
Geschrieben

kabel zu lang wäre eine möglichkeit, aber meine Kabel sind auch nicht grade kurz und alles läuft, ich hab 3 Tage gebraucht bevor alles lief (aber ich musste ja auch die scripte für den mmccombo schreiben ;) )

also ich kann wirklich die andere verkabelung für die sagem empfehlen, da die wie gesagt um einiges schneller ist

hast du mal den alten treiber probiert

hast du mal nachgeguckt ob pin 1 und 5 wirklich nicht vertauscht sind

unbenannt2ac5.jpg

so muss es sein

Link zu diesem Kommentar
Auf anderen Seiten teilen
caladon

caladon

Geschrieben
Geschrieben

Moin, moin.

 

Habs auch nach dieser Verkabelung angeschlossen. Jedoch die Karte an den Kontakten fest verlötet (soll eh nichts außer die ausgelagerten Daten drauf).

Karten: 256MB Kingston SD. Läuft mit der Einstellung "zu Fuß" V1 Beta6 und auch mit dem V2 Beta7 jedoch habe ich unter Treiber auswählen die 1 genommen.

Link zu diesem Kommentar
Auf anderen Seiten teilen
blomber

blomber

Geschrieben
  • Autor
Geschrieben

habs nach o.a. schema angeschlossen und wie gesagt alles durchgemessen.

 

ich will mal gucken, ob ich mir ne 256'er oder 512'er SD-Karte von Transcend beschaffen kann. vielleicht klappte ja mit der.

ansonsten bin ich kurz davor, die stecker an meinem interface abzukneifen und die kabel kürzer fest zu verlöten, um zu schauen, obs mit kürzeren kabeln funzt.

 

wenn nicht einer noch ne anere idee hat.

Link zu diesem Kommentar
Auf anderen Seiten teilen
caladon

caladon

Geschrieben
Geschrieben

Moin, moin.

 

Ich habe meine Kabel an der MC-Platine angelötet. An der Karte die Kabel auch fest verlötet. Die Karte anschließend am MC angeklebt. Läuft! Kabellänge max. 6-7 cm. Wobei ich nicht glaube das ein längeres Kabel nicht funktionieren sollte.

Wenn du jedoch ein extrem kurzes Kabel(Leitung) haben möchtest, kannst Du auch die Lötpunkte auf der Rückseite des Boards nutzen und hier die SD anlöten. Danach Kabel nach oben ziehen und auf dem Board/Gehäuse mit Heißkleber fixieren. Da könnten Kabellängen von unter 5 cm machbar sein!

 

... und auf die SD-Karte kommst Du ja auch immer per FTP, solltest Du Musik oder Pics drauf spielen wollen.

Link zu diesem Kommentar
Auf anderen Seiten teilen

Archiviert

Dieses Thema ist jetzt archiviert und für weitere Antworten gesperrt.

Gehe zur Themenübersicht

  • Wer ist Online   0 Benutzer

    • Keine registrierten Benutzer online.
×
×
  • Neu erstellen...