dbox2 platt?

[hoemma]

hallo zusammen,

 

seit gestern morgen empfängt meine dbox2 (nokia sat, 2xI) keinen sender mehr. nachdem neustart, kanalsuche und neuflashen keinen erfolg brachten, vermutete ich zunächst einen schaden am lnb, da es in der nacht heftig gewittert hat. mein vermieter (wir hängen zu zweit an der schüssel) versichterte mir jedoch, dass er nach wie vor jeden kanal empfangen würde (dbox2 philips). somit scheint es wohl eher an meinem receiver zu liegen. ich habe testweise mal einen alten analogreceiver angeschlossen, den ich hier noch rumfliegen hatte, auch der empfing das astra-signal tadellos. einen softwareseitigen fehler kann ich weitestgehend ausschliessen, da keine einstellungsänderung seit dem letzten mal, wo es funktioniert hat vorgenommen wurden. auch das neuflashen des images (KEYWELT_V1_SEPTEMBER_2x_SQUASHFS_2006) brachte keinen erfolg. hab auch mal testweise das aktuelle sportster-image draufgekloppt und meine settings eingespielt.

 

satfind weist einen BER-Wert von 0 aus und die anderen beiden werte sind z.b. bei ARD und ZDF bei über 50.000. das sollte für einen störungsfreien empfang eigentlich reichen. leider bekomme ich nur den allseits beliebten popup "kanal z.zt. nicht verfügbar". scheint wohl so, als ob der tuner defekt sei.

 

was meint ihr?

[Klo]

Kann durchaus sein !

 

Ansonsten erstell doch mal nen Bootlog und poste diesen hier rein.

Vielleicht lässt sich ja ein Hardwarefehler darin erkennen.

 

Gruß

Klo

[hoemma]

stimmt, kann ich mal machen. werde ich in den nächsten tagen mal machen. hab leider gerade mein nullmodemkabel verliehen!

[hoemma]

so, nullmodemkabel ist wieder aufgetaucht, hier der log! hoffe, dass sich was finden lässt...

 

 

01.01.1970 01:15:02 camd3: fahre runter... 01.01.1970 01:15:02 camd3: HTTP: stopped 01.01.1970 01:15:02 camd3: UDP: fahre runter... 01.01.1970 01:15:02 camd3: Slot /dev/tts/1: schliesse...

01.01.1970 01:15:02 camd3: Slot /dev/tts/1: warte auf Monitor... CXA2092 found
01.01.1970 01:15:03 camd3: Slot /dev/tts/1: geschlossen

01.01.1970 01:15:03 camd3: KeyDB: beendet

01.01.1970 01:15:03 camd3: camd v3.868 - erfolgreich beendet Unmounting 'ramfs' on '/tmp'
umount: Couldn't umount /tmp: No such file or directory

Unmounting 'jffs2' on '/var'
umount: forced umount of /var failed!
Oops: umount failed :-(  --  trying to remount readonly...
Ready to shutdown system...


The system is going down NOW !!Exiting Syslogd!
[nhttpd] stop requested......

Sending SIGKILL to all processes.

Please stand by while rebooting the system.
debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS
debug: BMon V1.0  mID 01
debug: feID dd    gtxID 0b
debug: fpID 5a     dsID XXXXXXXXXXX
debug: HWrev X5  SWrev 0.81
debug: B/Ex/Fl(MB) 32/00/08
WATCHDOG reset enabled
dbox2:root> debug: 
BOOTP/TFTP bootstrap loader (v0.3)
debug: 
debug: Transmitting BOOTP request via broadcast
debug: Given up BOOTP/TFTP boot
boot net failed

Flash-FS bootstrap loader (v1.5)

Found Flash-FS superblock version 3.1

Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS
debug: Got Block #0032
debug: Got Block #0004
debug: Got Block #0008
debug: Got Block #0012
debug: Got Block #0016
debug: Got Block #0020
debug: Got Block #0024
debug: Got Block #0028
debug: Got Block #0032 
will verify ELF image, start= 0x800000, size= 155204
verify sig: 262
Branching to 0x40000


U-Boot 1.1.4 (Tuxbox) (Aug 31 2006 - 20:09:02)

CPU:   PPC823ZTnnA at 67.200 MHz: 2 kB I-Cache 1 kB D-Cache
        *** Warning: CPU Core has Silicon Bugs -- Check the Errata ***
Board: DBOX2, Nokia, BMon V1.0
      Watchdog enabled
I2C:   ready
DRAM:  32 MB
FLASH:  8 MB
Scanning JFFS2 FS:   .  | .  / - .  \ .  | / - \ | /  done. FB:    ready
LCD:   ready
In:    serial

Out:   serial
Err:   serial
Net:   SCC ETHERNET

Options:
 1: Console on null
 2: Console on ttyS0

 3: Console on framebuffer
Select option (1-3), other keys to stop autoboot:  1  0 
### FS (squashfs) loading 'vmlinuz' to 0x100000
### FS load complete: 696900 bytes loaded to 0x100000
...............................................................
Un-Protected 63 sectors
## Booting image at 00100000 ...
  Image Name:   dbox2
  Image Type:   PowerPC Linux Kernel Image (gzip compressed)
  Data Size:    696836 Bytes = 680.5 kB
  Load Address: 00000000
  Entry Point:  00000000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK
Linux version 2.4.32-dbox2 (image@tower) (gcc version 3.4.4) #1 Do Aug 31 20:09:34 CEST 2006

On node 0 totalpages: 8192

zone(0): 8192 pages.

zone(1): 0 pages.

zone(2): 0 pages.

Kernel command line: console=ttyS0 root=/dev/mtdblock1 rootfstype=squashfs

Decrementer Frequency = 252000000/60

m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1)

m8xx_wdt: keep-alive trigger installed (PITC: 0x12C0)

Console: colour dummy device 80x25

Calibrating delay loop... 66.76 BogoMIPS

Memory: 30776k available (1184k kernel code, 348k data, 60k init, 0k highmem)

Dentry cache hash table entries: 4096 (order: 3, 32768 bytes)

Inode cache hash table entries: 2048 (order: 2, 16384 bytes)

Mount cache hash table entries: 512 (order: 0, 4096 bytes)

Buffer cache hash table entries: 1024 (order: 0, 4096 bytes)

Page-cache hash table entries: 8192 (order: 3, 32768 bytes)

POSIX conformance testing by UNIFIX

Linux NET4.0 for Linux 2.4

Based upon Swansea University Computer Society NET3.039

Initializing RT netlink socket

Starting kswapd

devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)

devfs: boot_options: 0x1

JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.

Squashfs 2.2-r2 (released 2005/09/08) (C) 2002-2005 Phillip Lougher

i2c-core.o: i2c core module version 2.6.1 (20010830)

i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830)

CPM UART driver version 0.04

ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2

pty: 256 Unix98 ptys configured

eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:1f:d8:19

loop: loaded (max 8 devices)

D-Box 2 flash driver (size->0x800000 mem->0x10000000)

D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank

Intel/Sharp Extended Query Table at 0x0035

cfi_cmdset_0001: Erase suspend on write enabled

Creating 6 MTD partitions on "D-Box 2 flash memory":

0x00000000-0x00020000 : "BR bootloader"

0x00020000-0x00540000 : "root (squashfs)"

0x00540000-0x007e0000 : "var (jffs2)"

0x007e0000-0x00800000 : "FLFS (U-Boot)"

0x00020000-0x00800000 : "Flash without bootloader"

0x00000000-0x00800000 : "Complete Flash"

Linux video capture interface: v1.00

mice: PS/2 mouse device common for all mice

NET4: Linux TCP/IP 1.0 for NET4.0

IP Protocols: ICMP, UDP, TCP, IGMP

IP: routing cache hash table of 512 buckets, 4Kbytes

TCP: Hash tables configured (established 2048 bind 4096)

Linux IP multicast router 0.06 plus PIM-SM

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.

VFS: Mounted root (squashfs filesystem) readonly.

Mounted devfs on /dev

Freeing unused kernel memory: 60k init


init started:  BusyBox v1.1.3 (2006.08.31-18:14+0000) multi-call mount: Mounting /dev/mtdblock/2 on /var failed: No such file or directory
event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $

Detected STB:

 Vendor: Nokia
 Model: D-BOX2 
[i2c-8xx]: mpc 8xx i2c init

[i2c-8xx]: adapter: 0

$Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $

$Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $

DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600).

dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter

$Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $

avia_av: $Id: avia_av_core.c,v 1.99 2006/01/08 21:36:22 carjay Exp $

avia_av_core: Starting avia_av_wdt thread.

avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $

avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $

avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $

avia_gt_core: autodetecting chip type... GTX

avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $

avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $

avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $

avia_gt_core: masking unhandled irq reg 1 bit 11

avia_gt_core: masking unhandled irq reg 1 bit 13

avia_gt_ucode: loaded ucode v0014

avia_gt_ucode: ucode section filters disabled.

avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning...

avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $

avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $

avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $

avia_gt_core: Loaded AViA eNX/GTX driver

avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

Console: switching to colour frame buffer device 82x32

avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device

lcd.o: init lcd driver module

lcd.o: found KS0713/SED153X lcd interface

avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $

avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $

avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $

avia_gt_pcm_set_rate(44100)

avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $

DVB: registering frontend 0:0 (VES1893)...

avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $

avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $

avia_gt_proc: $Id: avia_gt_proc.c, v 0.1.3 2005/12/11 22:30:00 Skars & Merandos Exp $

avia_gt_proc: Description: GTX/ENX proc_dev Driver with proc_fs extension

options:

(demux reinit)  enx_reset=1

(framer chan.)  fc_reset=1

(clr avia reg)  avia=0

(enx td trace)  trace=1

(lock, unlock)  spinlock=0

Schreiben ueber /proc/bus/gtx

(delay)         delay=500

cdkVcInfo $Id: cdkVcInfo.c,v 1.0 2002/09/26 20:48:26 alexW Exp $

Starting the automounter

Please press Enter to activate this console. Thu Jan  1 01:00:00 CET 1970
$Id: sectionsd.cpp,v 1.227 2006/06/08 20:19:32 houdini Exp $
[sectionsd] Caching max 6000 events
[sectionsd] Caching 14 days
[sectionsd] Events are old 60min after their end time
/var/plugins/operations logcs_init
/var/plugins/operations camd_init
$Id: zapit.cpp,v 1.389 2006/06/08 20:17:58 Kroki & Worschter Exp $
[zapit] MAX_SOCKETS=3
[zapit] PMT update enabled
/var/plugins/operations cardserver_start
/var/plugins/operations camd_start
insmod: Warning: kernel-module version mismatch
/var/modules/multicam.o was compiled for kernel version 2.4.25-dbox2

while this kernel is version 2.4.32-dbox2
DBox2 Multicam Driver v1.01 skars & doz21 :)

starte camd3
/var/plugins/operations check_camd3_socket
01.01.1970 01:00:10 camd3: BOXTYPE:  1 01.01.1970 01:00:10 camd3: LOG:  6 01.01.1970 01:00:10 camd3: UDP_PORT:  20248 01.01.1970 01:00:10 camd3: original slot au on 01.01.1970 01:00:10 camd3: HTTP_PORT:  9080 01.01.1970 01:00:10 camd3: LOG_HOST:  127.0.0.1:514

01.01.1970 01:00:10 camd3: DNS_CACHE:  600 sec 01.01.1970 01:00:10 camd3: SOCKET:  /tmp/camd.sock01 01.01.1970 01:00:10 camd3: KEYS:    /var/keys/camd3.keys 01.01.1970 01:00:11 camd3: SERVERS:   /var/keys/camd3.servers 01.01.1970 01:00:11 camd3: USERS:   /var/keys/camd3.users


01.01.1970 01:00:11 camd3: Slot /dev/tts/1: (carddetect=password1) initialisiere... 01.01.1970 01:00:12 camd3: Slot /dev/tts/1: starte Monitor... 01.01.1970 01:00:12 camd3: Slot /dev/tts/1: bereit 01.01.1970 01:00:13 camd3: KeyDB: gestartet 01.01.1970 01:00:13 camd3: HTTP: started on port 9080 01.01.1970 01:00:13 camd3: camd v3.868 - erfolgreich gestartet [getservices] /var/tuxbox/config/zapit/myservices.xml  found.
[getservices] dup transponder id 3 onid 85
[getservices] dup transponder id 11 onid 85
[getservices] dup transponder id 2 onid 85
[getservices] dup transponder id 4 onid 85
[getservices] dup transponder id 1 onid 85
/tmp/currentservices.xml: No such file or directory
$Id: controld.cpp,v 1.124 2006/06/27 10:21:59 barf Exp $

[controld] Boxtype detected: (1, Nokia D-BOX2)
[controld]: ROUTEVIDEO v1 = 5 a1 = 1 v2 = 1 a2 = 1 v3 = 0 a3 = 1 fblk=1
[nhttpd] Neutrino HTTP-Server starting..
[LCDFONT] initializing core.../var/plugins/operations epg_reinit

[LCDFONT] adding font /share/fonts/micron.ttf...OK (Micron/Regular)
[LCDFONT] adding font /share/fonts/micron_bold.ttf...OK (Micron/Bold)
[LCDFONT] adding font /share/fonts/pakenham.ttf...OK (Pakenham/Regular)
[LCDFONT] Intializing font cache...
neutrino: /lib/libpng12.so.0: no version information available (required by neutrino)
[neutrino] frameBuffer Instance created
812k video mem
avia_gt_gv: set_input_mode (mode=2)

avia_gt_gv: set_input_size (width=720, height=576)

[neutrino] Software update enabled

[neutrino] enable flash
[lcdd] time-skin not found -> using default...
[lcdd] weekday-skin not found -> using default...
[lcdd] date-skin not found -> using default...
[lcdd] month-skin not found -> using default...
[LCDFONT] initializing core...
[LCDFONT] adding font /share/fonts/12.pcf.gz...[sectionsd] getUTC: read: Connection timed out
OK (Fix12/Regular)
[LCDFONT] adding font /share/fonts/14B.pcf.gz...OK (Fix14/Bold)
[LCDFONT] adding font /share/fonts/15B.pcf.gz...OK (Fix15/Bold)
[LCDFONT] Intializing font cache...
[LCDFONT] FTC_Face_Requester (Fix15/Bold)

[LCDFONT] FTC_Face_Requester (Fix14/Bold)

/dev/input/event1: No such file or directory
[neutrino] menue setup
[neutrino] received 33 sats

[neutrino] registering as event client
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[basicsocket] send_data: Resource temporarily unavailable
[neutrino] initialized everything
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[zapit] pat parsing failed
[zapit] retry......
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[zapit] pat parsing failed
[zapit] retry......
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[zapit] pat parsing failed
[zapit] retry......
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[zapit] pat parsing failed
[zapit] retry......
[dmx.cpp:read:184] read(fd, buf, n): Connection timed out
[zapit] pat parsing failed
zap failed!
[sectionsd] getUTC: read: Connection timed out
[sectionsd] getUTC: read: Connection timed out

[Cyberjunkie]

Sorry, passt nicht zum Thema, aber bitte nimm die DSID Raus

 

hier das:

debug: fpID 5a    dsID

 

DANKE

[Klo]

Also wenn Du BER 0 hast sollte der Tuner ganz sein !

 

Ich vermute mal dass ein anderes Bauteil defekt oder angeschlagen ist (wie zum Bleistift der SEC)...

 

Ich würde an Deiner Stelle das Log mal an Ralf Jürgen Bader schicken und mir dazu einen Kostenvoranschlag machen lassen.

 

klick

 

Grüße

 

Klo

[hoemma]

Also wenn Du BER 0 hast sollte der Tuner ganz sein !

 

Ich vermute mal dass ein anderes Bauteil defekt oder angeschlagen ist (wie zum Bleistift der SEC)...

 

Ich würde an Deiner Stelle das Log mal an Ralf Jürgen Bader schicken und mir dazu einen Kostenvoranschlag machen lassen.

 

klick

 

Grüße

 

Klo

ja, hab ich mal gemacht... hab ja schon ganz gute erfahrungen mit sportsfreund bader gemacht

 

ist ja nicht meine erste defekte dbox!