posmu Geschrieben 14. Oktober 2005 Melden Share Geschrieben 14. Oktober 2005 (bearbeitet) Hi! Mein CS Partner hat ein RIESEN Problem mit seiner Box! Hier sein Bootlog ! [debug: DDF: Calibrating delay loop... debug: DDF: 67.79 BogoMIPS debug: BMon V1.2 mID 01 debug: feID dd gtxID 0b debug: fpID 5a dsID xxxxx debug: HWrev 09 FPrev 0.81 debug: B/Ex/Fl(MB) 32/00/08 WATCHDOG reset enabled dbox2:root> debug: BOOTP/TFTP bootstrap loader (v0.3) debug: debug: Transmitting BOOTP request via broadcast debug: Given up BOOTP/TFTP boot boot net failed Flash-FS bootstrap loader (v1.5) Found Flash-FS superblock version 3.1 Found file /root/platform/nokia-dbox2/kernel/os in Flash-FS debug: Got Block #0032 will verify ELF image, start= 0x800000, size= 155528 verify sig: 263 Branching to 0x40000 U-Boot 1.1.2 (Tuxbox) (Aug 28 2005 - 14:12:52) CPU: PPC823ZTnnB2 at 67.100 MHz: 2 kB I-Cache 1 kB D-Cache Board: DBOX2, Nokia, BMon V1.2 Watchdog enabled I2C: ready DRAM: 32 MB FLASH: 8 MB Scanning JFFS2 FS: ........... done. FB: ready LCD: ready In: serial Out: serial Err: serial Net: SCC ETHERNET Options: 1: Console on null 2: Console on ttyS0 3: Console on framebuffer Select option (1-3), other keys to stop autoboot: 0 ### FS (jffs2) loading 'vmlinuz' to 0x100000 ### FS load complete: 643620 bytes loaded to 0x100000 ............................................................... Un-Protected 63 sectors ## Booting image at 00100000 ... Image Name: dbox2 Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 643556 Bytes = 628.5 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.4.31-dbox2 (gweny@linux) (gcc version 3.3.5) #1 Fr Sep 23 20:00: 30 CEST 2005 On node 0 totalpages: 8192 zone(0): 8192 pages. zone(1): 0 pages. zone(2): 0 pages. Kernel command line: console=ttyS0 root=/dev/mtdblock2 rw Decrementer Frequency = 251625000/60 m8xx_wdt: active wdt found (SWTC: 0xFFFF, SWP: 0x1) m8xx_wdt: keep-alive trigger installed (PITC: 0x2580) Warning: real time clock seems stuck! Console: colour dummy device 80x25 Calibrating delay loop... 66.76 BogoMIPS Memory: 30840k available (1096k kernel code, 372k data, 60k init, 0k highmem) Dentry cache hash table entries: 4096 (order: 3, 32768 bytes) Inode cache hash table entries: 2048 (order: 2, 16384 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer cache hash table entries: 1024 (order: 0, 4096 bytes) Page-cache hash table entries: 8192 (order: 3, 32768 bytes) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd devfs: v1.12c (2002081 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x1 JFFS2 version 2.2. (NAND) © 2001-2003 Red Hat, Inc. Squashfs 2.1-r2 (released 2004/12/15) © 2002-2004 Phillip Lougher i2c-core.o: i2c core module version 2.6.1 (20010830) i2c-dev.o: i2c /dev entries driver module version 2.6.1 (20010830) CPM UART driver version 0.04 ttyS0 at 0x0280 is on SMC1 using BRGttyS1 at 0x0380 is on SMC2 using BRG2 pty: 256 Unix98 ptys configured eth0: CPM ENET Version 0.2.dbox2 on SCC2, 00:50:9c:44:0f:4f D-Box 2 flash driver (size->0x800000 mem->0x10000000) D-Box 2 flash memory: Found 2 x16 devices at 0x0 in 32-bit bank Intel/Sharp Extended Query Table at 0x0035 cfi_cmdset_0001: Erase suspend on write enabled Creating 5 MTD partitions on "D-Box 2 flash memory": 0x00000000-0x00020000 : "BR bootloader" 0x00020000-0x00040000 : "FLFS (U-Boot)" 0x00040000-0x00800000 : "root (jffs2)" 0x00020000-0x00800000 : "Flash without bootloader" 0x00000000-0x00800000 : "Complete Flash" Linux video capture interface: v1.00 mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. cramfs: wrong magic VFS: Mounted root (jffs2 filesystem). Mounted devfs on /dev Freeing unused kernel memory: 60k init Starting pid 11, console /dev/console: '/etc/init.d/rcS'ti-call b Using /lib/modules/2.4.31-dbox2/misc/tuxbox.o Detected STB: Vendor: Nokia Model: D-BOX2 Using /lib/modules/2.4.31-dbox2/misc/dvb-core.o Using /lib/modules/2.4.31-dbox2/misc/dbox2_i2c.o [i2c-8xx]: mpc 8xx i2c init [i2c-8xx]: adapter: 0 Using /lib/modules/2.4.31-dbox2/misc/dvb_i2c_bridge.o Using /lib/modules/2.4.31-dbox2/misc/event.o event: $Id: event.c,v 1.12 2003/09/30 05:45:38 obi Exp $ Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp.o Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_input.o Using /lib/modules/2.4.31-dbox2/misc/ves1820.o Using /lib/modules/2.4.31-dbox2/misc/ves1x93.o Using /lib/modules/2.4.31-dbox2/misc/avs.o Using /lib/modules/2.4.31-dbox2/misc/saa7126.o Using /lib/modules/2.4.31-dbox2/misc/cam.o $Id: cam.c,v 1.30 2004/01/10 16:36:34 alexw Exp $ Using /lib/modules/2.4.31-dbox2/misc/lcd.o lcd.o: init lcd driver module lcd.o: found KS0713/SED153X lcd interface Using /lib/modules/2.4.31-dbox2/misc/avia_napi.o $Id: avia_napi.c,v 1.18 2003/11/24 09:53:01 obi Exp $ DVB: registering new adapter (C-Cube AViA GTX/eNX with AViA 500/600). DVB: registering frontend 0:0 (VES1893)... dvb_i2c_bridge: enabled DVB i2c bridge to PowerPC 8xx I2C adapter Using /lib/modules/2.4.31-dbox2/misc/avia_av.o avia_av: $Id: avia_av_core.c,v 1.98 2004/11/21 20:33:38 carjay Exp $ avia_av_core: Starting avia_av_wdt thread. avia_av_event: $Id: avia_av_event.c,v 1.11 2003/10/26 16:32:51 obi Exp $ avia_av_proc: $Id: avia_av_proc.c,v 1.14 2004/01/21 20:02:29 carjay Exp $ Using /lib/modules/2.4.31-dbox2/misc/avia_gt.o avia_gt_core: $Id: avia_gt_core.c,v 1.48 2004/12/20 01:01:22 carjay Exp $ avia_gt_core: autodetecting chip type... GTX avia_gt_gtx: $Id: avia_gt_gtx.c,v 1.24 2003/09/30 05:45:35 obi Exp $ avia_gt_accel: $Id: avia_gt_accel.c,v 1.19 2003/09/30 05:45:35 obi Exp $ avia_gt_dmx: $Id: avia_gt_dmx.c,v 1.210 2004/06/26 16:08:15 carjay Exp $ avia_gt_core: masking unhandled irq reg 1 bit 11 avia_gt_core: masking unhandled irq reg 1 bit 13 avia_gt_ucode: loaded ucode v0014 avia_gt_ucode: ucode section filters disabled. avia_gt_dmx: warning, misaligned queue 0 (is 0xFD200, size 65536), aligning... avia_gt_gv: $Id: avia_gt_gv.c,v 1.39 2004/08/28 16:44:56 carjay Exp $ avia_gt_gv: set_input_size (width=720, height=576) avia_gt_pcm: $Id: avia_gt_pcm.c,v 1.29 2004/01/29 19:38:20 zwen Exp $ avia_gt_pcm_set_rate(44100) avia_gt_capture: $Id: avia_gt_capture.c,v 1.32 2003/09/30 05:45:35 obi Exp $ avia_gt_pig: $Id: avia_gt_pig.c,v 1.40 2003/09/30 05:45:35 obi Exp $ avia_gt_vbi: $Id: avia_gt_vbi.c,v 1.26 2003/08/01 17:31:22 obi Exp $ avia_gt_core: Loaded AViA eNX/GTX driver Using /lib/modules/2.4.31-dbox2/misc/avia_gt_fb.o avia_gt_fb: $Id: avia_gt_fb_core.c,v 1.54 2004/03/17 18:42:18 zwen Exp $ avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) Console: switching to colour frame buffer device 82x32 avia_gt_fb: fb0: AViA eNX/GTX Framebuffer frame buffer device Using /lib/modules/2.4.31-dbox2/misc/avia_gt_lirc.o avia_gt_lirc: $Id: avia_gt_lirc.c,v 1.14 2003/09/30 05:45:35 obi Exp $ avia_gt_ir: $Id: avia_gt_ir.c,v 1.30 2003/09/30 05:45:35 obi Exp $ Using /lib/modules/2.4.31-dbox2/misc/avia_gt_oss.o avia_oss: $Id: avia_gt_oss.c,v 1.26 2004/05/31 22:56:02 carjay Exp $ avia_gt_pcm_set_rate(44100) Using /lib/modules/2.4.31-dbox2/misc/avia_gt_v4l2.o avia_gt_v4l2: $Id: avia_gt_v4l2.c,v 1.12 2003/09/30 04:54:03 obi Exp $ Using /lib/modules/2.4.31-dbox2/misc/cam_napi.o $Id: cam_napi.c,v 1.8 2003/09/30 05:45:34 obi Exp $ Using /lib/modules/2.4.31-dbox2/misc/avia_av_napi.o avia_av_napi.c: $Id: avia_av_napi.c,v 1.33 2004/03/11 15:30:27 derget Exp $ Using /lib/modules/2.4.31-dbox2/misc/avia_gt_napi.o avia_gt_napi: $Id: avia_gt_napi.c,v 1.203 2005/01/05 05:49:56 carjay Exp $ Using /lib/modules/2.4.31-dbox2/misc/dvb2eth.o Using /lib/modules/2.4.31-dbox2/misc/aviaEXT.o Using /lib/modules/2.4.31-dbox2/misc/dbox2_fp_napi.o Using /lib/modules/2.4.31-dbox2/misc/avia_gt_proc.o avia_gt_proc: $Id: avia_gt_proc.c, v 0.1.3 2003/09/25 12:24:00 Skars & Merandos Exp $ avia_gt_proc: Description: GTX/ENX proc_dev Driver with proc_fs extension options: (demux reinit) enx_reset=1 (framer chan.) fc_reset=1 (clr avia reg) avia=1 (enx td trace) trace=0 (lock, unlock) spinlock=0 Schreiben ueber avia_gt.o (delay) delay=10 Using /lib/modules/2.4.31-dbox2/misc/multicam.o DBox2 Multicam Driver v1.01 skars & doz21 Using /lib/modules/2.4.31-dbox2/kernel/net/sunrpc/sunrpc.o Using /lib/modules/2.4.31-dbox2/kernel/fs/lockd/lockd.o Using /lib/modules/2.4.31-dbox2/kernel/fs/nfs/nfs.o Using /lib/modules/2.4.31-dbox2/kernel/fs/cifs/cifs.o [AVS] i2c error -121 Starting pid 103, console /dev/console: '/etc/init.d/start' Please press Enter to activate this console. cdkVcInfo $Id: cdkVcInfo.c,v 1.0 20 02/09/26 20:48:26 alexW Exp $ [AVS] i2c error -121 [AVS] i2c error -121 <14>Jan 1 01:00:28 camd3: BOXTYPE: 1 <14>Jan 1 01:00:28 camd3: LOG: 2 <14>Jan 1 01:00:29 camd3: UDP_PORT: 20248 <14>Jan 1 01:00:29 camd3: original slot au on <14>Jan 1 01:00:29 camd3: SOCKET: /tmp/camd.socket <14>Jan 1 01:00:29 camd3: KEYS: /var/keys/camd3.keys <14>Jan 1 01:00:29 camd3: SERVERS: /var/keys/camd3.servers <14>Jan 1 01:00:29 camd3: USERS: /var/keys/camd3.users <14>Jan 1 01:00:29 camd3: Slot /dev/tts/1: initialisiere... <14>Jan 1 01:00:30 camd3: Slot /dev/tts/1: starte Monitor... <14>Jan 1 01:00:30 camd3: Slot /dev/tts/1: bereit <14>Jan 1 01:00:30 camd3: /var/keys/camd3.servers: HOST=192.168.0.25 PORT=20248 <14>Jan 1 01:00:30 camd3: USER=benutzer1 PASS=password1 SERVICES=All <14>Jan 1 01:00:31 camd3: UserDB(neu): USER=benutzer2 PASS=password2 SERVICES=A lle, <14>Jan 1 01:00:31 camd3: KeyDB: gestartet <14>Jan 1 01:00:31 camd3: camd v3.810 - erfolgreich gestartet [AVS] i2c error -121 [AVS] i2c error -121 avia_gt_gv: set_input_mode (mode=2) avia_gt_gv: set_input_size (width=720, height=576) sh: cannot open /share/keymaps/eng.kmap: No such file [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 saa7126_readbuf: i2c read error (ret == -121) [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 [AVS] i2c error -121 Was kann bedeuten? andere img wollen auch nicht mehr! Er hat schon kalibo probiert. das läuft 5 min und geht denn aus DBox 2 --> Nokia 2xI AVIA 600L Ist der Tuner defekt? Bitte helft uns!!! Danke! Gruß, Peter bearbeitet 15. Oktober 2005 von Modern World Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
abwl Geschrieben 15. Oktober 2005 Melden Share Geschrieben 15. Oktober 2005 Als erstes editiere mal deine dsID weg Nun zum Problem. Die Meldung [AVS] i2c error -121 deutet auf einen Fehler im i2c-Bus hin. Der steuert jede Menge Systemteile und den Fehler zu identifizieren dürfte quasi unmöglich sein. Der hardwareschaden am Bus ist auch nicht reparabel. Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Modern World Geschrieben 15. Oktober 2005 Melden Share Geschrieben 15. Oktober 2005 Als erstes editiere mal deine dsID weg ich habe es mal editiert... Link zu diesem Kommentar Auf anderen Seiten teilen More sharing options...
Empfohlene Beiträge