Jump to content

Zee² mit Problemen am zweiten Kabeltuner


skyline666

Empfohlene Beiträge

Liebe Kollegen,

 

ich bin im Besitz von einer Zee². Installiert das Kabel Image 3.92.

Jetzt fällt mir auf, dass ich nicht mehr parallel aufnehmen und einen zweiten Sender (außerhalb dem Programmkanälen des ersten Senders) sehen kann.

Also ich schaue Sky und möchte ARD aufnehmen! Geht nicht mehr.

Weiterhin ist mir aufgfallen, dass im OSD Menü (beim Umschalten und oder OK drücken) unten links nur noch CS1 erscheint und daneben wo normal ja

wohl CS2 erscheinen sollte nichts steht und ein leerer Platz zu sehen ist.

Die Kabeltuner habe ich auf independent gesetzt und dies auch mal ein und ausgeschaltet.

Alles ohne Erfolg.

 

Gibt es die Möglichkeit hier etwas zu analysieren?

 

Hilft ggf. noch einmal ein Image rüber zu bügeln?

 

Klasse wäre das wenn wir hier zu einer Lösung kommen würden.

 

Frohes Fest Skyline666

 

 

Link zu diesem Kommentar
Auf anderen Seiten teilen

Hallo Gandalf, Du machst mir Mut und ich würde mal versuchen ein Protokoll (bootlog) vom Start zu posten. Hatte nur die Hoffnung, dass ggf. so ein Problem auch mit einem überschreiben des aktuellen Image auch zu beheben ist.

 

Könnte ich auch den Hinweis aus dem Kernelmeldungen aus dem yWeb posten?

 

Ich muss mich auch korrigieren. Habe festgestellt das bei meiner anderen Box auch nur ein Button mit dem Hinweis CI1 existiert und nicht zwei. 


Ist meine Annahme richtig, dass eine Zee2 ein besseres Bild liefert als eine Neo2?


Mit freundlichen Grüßen 

 

skyline666

Link zu diesem Kommentar
Auf anderen Seiten teilen

So hier mal das boot-log für die Profis!

 




Starting Microloader ASM built on Mar 28 2016 18:03:24...
Initializing PLLs...
Initializing Clocks..
Initializing DDR PLLs/Clocks...
Initializing DDR controller...
Initializing data section...
Initializing stack ptr...
Starting Microloader C...
Chip: KRONOS
Found Internal MYSTI110 PHY on GMAC0
Checking for Guide button press ...
GCS in ISA MODE
GCS: SFC DEVICE SETUP COMPLETE
BOX MAC OK!
BOX: Type: ZEE Rev: 75500100
Setting up default ATAG list...
Jumping to U-Boot ...
BOOT_TIME: 601 ms since POR

--------------------------------------------------------------------------------
| U-Boot 2009.08-00068-g69a4049 (Dec 10 2015 - 14:51:59)               CST HDx |
|------------------------------------------------------------------------------|
| Chipset information                                                          |
| Vendor: Entropic  Type: KRONOS           Revision: B0        Fuses: 00010001 |
|------------------------------------------------------------------------------|
| Clock information                                                            |
| *** not available yet ***                                                    |
|------------------------------------------------------------------------------|
| Frontpanel information                                                       |
| Vendor: CST       Version: 3.3           Display: OLED (128 x 64 px)         |
|------------------------------------------------------------------------------|
| Memory configuration                                                         |
| Start    | End      | Type    | Description                                  |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 1FFFFFFF | RAM     | System main memory bank #0 (512M)            |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K x  64)      |
  *** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit               |
|------------------------------------------------------------------------------|
| Network configuration                                                        |
| MAC: LIP 6300                    address: 00-C5-5C-25-BA-B7                  |
--------------------------------------------------------------------------------

Hit any key to stop autoboot:  0

SFC read: offset 0x100000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Coolstream Kernel (compressed)
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2981377 Bytes =  2.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.10.93 (image@server) (gcc version 6.3.1 20170109 (crosstool-NG 1) ) #1 SMP Sun Apr 15 15:27:43 CEST 2018
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Entropic Kronos STB Platform with FDT, model: CoolStream HD2 Kronos STB
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Early platform io descriptors mapping...
[    0.000000] PERCPU: Embedded 7 pages/cpu @80da8000 s5952 r8192 d14528 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 247144k/247144k available, 277144k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.000000]       .text : 0x80008000 - 0x806584f8   (6466 kB)
[    0.000000]       .init : 0x80659000 - 0x80687740   ( 186 kB)
[    0.000000]       .data : 0x80688000 - 0x806c8e60   ( 260 kB)
[    0.000000]        .bss : 0x806c8e60 - 0x806e3224   ( 105 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000]  RCU debugfs-based tracing is enabled.
[    0.000000]  Additional per-CPU info printed with stalls.
[    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
[    0.000000] NR_IRQS:350
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] GIC CPU mask not found - kernel will fail to boot.
[    0.000000] Cortex A9 frequency at 600 MHz
[    0.000000] Initializing Cortex A9 Global Timer at Vir:0xFEA00200, using, at Freq:300 MHz
[    0.000000] sched_clock: 32 bits at 300MHz, resolution 3ns, wraps every 14316ms
[    0.000000] smp_twd: clock not found -2
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.249870] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    0.292758] pid_max: default: 32768 minimum: 301
[    0.297559] Mount-cache hash table entries: 512
[    0.303981] CPU: Testing write buffer coherency: ok
[    0.309063] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.314686] Setting up static identity map for 0x803c47a0 - 0x803c47f8
[    0.321215] L310 cache controller enabled
[    0.325132] l2x0: 8 ways, CACHE_ID 0x410004c7, AUX_CTRL 0x32421001, Cache size: 131072 B
[    0.333758] Brought up 1 CPUs
[    0.336632] SMP: Total of 1 processors activated (1196.85 BogoMIPS).
[    0.342954] CPU: All CPU(s) started in SVC mode.
[    0.348217] devtmpfs: initialized
[    0.356569] NET: Registered protocol family 16
[    0.361679] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.475065] GMAC0: active interface is 1
[    0.479061] ChipID=0x1000 ChipRevID=0x100
[    0.483152] nx_dmac: Registered with 8 channels
[    0.509731] bio: create slab <bio-0> at 0
[    0.515228] GPIO: base febab000 (phys e06ab000)
[    0.519819] GPIO: base feb69000 (phys e0669000)
[    0.526207] SCSI subsystem initialized
[    0.531347] usbcore: registered new interface driver usbfs
[    0.536927] usbcore: registered new interface driver hub
[    0.542583] usbcore: registered new device driver usb
[    0.548014] pps_core: LinuxPPS API ver. 1 registered
[    0.552941] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.562233] PTP clock support registered
[    0.567795] cfg80211: Calling CRDA to update world regulatory domain
[    0.575590] Switching to clocksource arm_global_timer
[    0.599398] NET: Registered protocol family 2
[    0.604702] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.611789] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.618198] TCP: Hash tables configured (established 4096 bind 4096)
[    0.624548] TCP: reno registered
[    0.627694] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.633544] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.640018] NET: Registered protocol family 1
[    0.644798] RPC: Registered named UNIX socket transport module.
[    0.650641] RPC: Registered udp transport module.
[    0.655280] RPC: Registered tcp transport module.
[    0.659946] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.666514] PM: STB Platform power mgmt initialization.
[    0.797170] NFS: Registering the id_resolver key type
[    0.802256] Key type id_resolver registered
[    0.806334] Key type id_legacy registered
[    0.810360] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.816724] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.824706] msgmni has been set to 482
[    0.829754] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.837119] io scheduler noop registered
[    0.840977] io scheduler deadline registered
[    0.845841] io scheduler cfq registered (default)
[    0.851212] e06b2000.serial: ttyS0 at MMIO 0xe06b2000 (irq = 47) is a uart-ip3106
[    0.865619] loop: module loaded
[    0.869733] ahci-stb e0638000.sata: unable to find phy
[    0.874835] SATA: Enable mpll_ss_en (rd_val=0x571185, wr_val=0x5711a5)
[    0.881269] SATA: Enable rx_term_en0 (rd_val=0x277, wr_val=0x277)
[    0.887335] ahci-stb e0638000.sata: SSS flag set, parallel bus scan disabled
[    0.894345] ahci-stb e0638000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    0.903131] ahci-stb e0638000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    0.912602] ata4294967295: SATA PHY offline
[    0.917624] scsi0 : ahci_platform
[    0.921591] ata1: SATA max UDMA/133 mmio [mem 0xe0638000-0xe0638fff] port 0x100 irq 39
[    0.931064] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
[    0.943464] Bad block table found at page 262080, version 0x01
[    0.949976] Bad block table found at page 262016, version 0x01
[    0.956233] nand_read_bbt: bad block at 0x00001cf60000
[    0.961298] nand_read_bbt: bad block at 0x00001cfa0000
[    0.966421] 3 cmdlinepart partitions found on MTD device e0631000.flash_nand
[    0.973375] Creating 3 MTD partitions on "e0631000.flash_nand":
[    0.979243] 0x000000000000-0x000010000000 : "root0"
[    0.985791] 0x000010000000-0x000012000000 : "var"
[    0.991886] 0x000012000000-0x000020000000 : "root1"
[    1.000227] JEDEC ID = 0x1c3016 , Extended Device ID = 0x1c30
[    1.005966] nx_sfc e0632000.flash_sfc: en25q32 (4096 Kbytes)
[    1.011608] 5 cmdlinepart partitions found on MTD device e0632000.flash_sfc
[    1.018482] Creating 5 MTD partitions on "e0632000.flash_sfc":
[    1.024296] 0x000000000000-0x000000040000 : "uldr"
[    1.030685] 0x000000040000-0x0000000c0000 : "u-boot"
[    1.036977] 0x0000000c0000-0x0000000e0000 : "env"
[    1.043102] 0x0000000e0000-0x000000100000 : "spare"
[    1.049350] 0x000000100000-0x000000400000 : "kernel"
[    1.056400] tun: Universal TUN/TAP device driver, 1.6
[    1.061421] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    1.068063]  DWMAC1000
[    1.070366] stmmac - user ID: 0x36, Synopsys ID: 0x36
[    1.075347]  Ring mode enabled
[    1.078372]  DMA HW capability register supported
[    1.082882]  Enhanced/Alternate descriptors
[    1.087184]  Enabled extended descriptors
[    1.091170]  RX Checksum Offload Engine supported (type 2)
[    1.096602]  TX Checksum insertion supported
[    1.100842]  Wake-Up On Lan supported
[    1.104509]  Enable RX Mitigation via HW Watchdog Timer
[    1.124496] libphy: stmmac: probed
[    1.127809] eth0: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) active
[    1.134167] eth0: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
[    1.139815] eth0: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
[    1.145529] eth0: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
[    1.151233] eth0: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
[    1.156922] eth0: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
[    1.162632] eth0: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
[    1.168327] eth0: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
[    1.174036] eth0: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
[    1.179731] eth0: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
[    1.185441] eth0: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
[    1.191228] eth0: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
[    1.197011] eth0: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
[    1.202806] eth0: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
[    1.208589] eth0: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
[    1.214384] eth0: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
[    1.220171] eth0: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
[    1.225955] eth0: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
[    1.231749] eth0: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
[    1.237533] eth0: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
[    1.243328] eth0: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
[    1.249110] eth0: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
[    1.254905] eth0: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
[    1.260694] eth0: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
[    1.266477] eth0: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
[    1.272271] eth0: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
[    1.278054] eth0: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
[    1.283849] eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
[    1.289632] eth0: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
[    1.295426] eth0: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
[    1.301215] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
[    1.306998] eth0: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
[    1.313040] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.319455] ehci-platform: EHCI generic platform driver
[    1.324933] ehci-platform e066c000.usb: EHCI Host Controller
[    1.330565] ehci-platform e066c000.usb: new USB bus registered, assigned bus number 1
[    1.338385] ehci-platform e066c000.usb: irq 93, io mem 0xe066c000
[    1.360090] ehci-platform e066c000.usb: USB 2.0 started, EHCI 1.00
[    1.366243] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.372958] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.380115] usb usb1: Product: EHCI Host Controller
[    1.384932] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.390394] usb usb1: SerialNumber: e066c000.usb
[    1.395871] hub 1-0:1.0: USB hub found
[    1.399543] hub 1-0:1.0: 1 port detected
[    1.403717] ehci-platform e066d000.usb: EHCI Host Controller
[    1.409290] ehci-platform e066d000.usb: new USB bus registered, assigned bus number 2
[    1.417202] ehci-platform e066d000.usb: irq 94, io mem 0xe066d000
[    1.423256] ata1: SATA PHY offline
[    1.426572] ata1: SATA link down (SStatus 0 SControl 300)
[    1.440079] ehci-platform e066d000.usb: USB 2.0 started, EHCI 1.00
[    1.446232] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[    1.452946] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.460101] usb usb2: Product: EHCI Host Controller
[    1.464922] usb usb2: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.470375] usb usb2: SerialNumber: e066d000.usb
[    1.475761] hub 2-0:1.0: USB hub found
[    1.479436] hub 2-0:1.0: 1 port detected
[    1.484062] usbcore: registered new interface driver usb-storage
[    1.490466] usbcore: registered new interface driver usbserial
[    1.497766] usbcore: registered new interface driver usbhid
[    1.503308] usbhid: USB HID core driver
[    1.507301] TCP: cubic registered
[    1.510544] NET: Registered protocol family 17
[    1.515357] Key type dns_resolver registered
[    1.519637] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 3
[    1.527172] ThumbEE CPU extension supported.
[    1.532454] ### dt-test ### No testcase data in device tree; not running tests
[    1.730081] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    1.881891] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[    1.888507] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    1.895604] usb 1-1: Product: USB2.0 Hub
[    1.900898] hub 1-1:1.0: USB hub found
[    1.904888] hub 1-1:1.0: 4 ports detected
[    3.500065] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    4.403938] usb 2-1: New USB device found, idVendor=174c, idProduct=5136
[    4.410576] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    4.417616] usb 2-1: Product: AS2105
[    4.421173] usb 2-1: Manufacturer: ASMedia
[    4.425220] usb 2-1: SerialNumber: 00000000000000000000
[    4.434240] usb-storage 2-1:1.0: USB Mass Storage device detected
[    4.440522] scsi1 : usb-storage 2-1:1.0
[    5.441066] scsi 1:0:0:0: Direct-Access     ASMT     2105             0    PQ: 0 ANSI: 6
[    5.451074] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    5.459263] sd 1:0:0:0: [sda] Attached SCSI removable disk
[    7.557428] VFS: Mounted root (jffs2 filesystem) on device 31:0.
[    7.565107] devtmpfs: mounted
[    7.568277] Freeing unused kernel memory: 184K (80659000 - 80687000)
init started: BusyBox v1.30.1 (2019-06-22 15:09:50 CEST)
[    8.461771] NET: Registered protocol family 10
try to mount /dev/mtdblock1 to /var
starting /etc/init.d/S02loadmodules ...
Sat Jan  1 00:00:00 CET 2000
Creating device node for cs_display
Running insmod now .......
Driver modules loaded, please start the app now...
Creating device node for KAL
Creating device node for notifyq
Creating device node for platform
Creating device node for content
Creating device node for standby
Creating device node for video
Creating device node for audio
Creating device node for pvr
Creating device node for ci
Creating device node for cs_control
Creating device node for cs_ir
Creating device node for fb
starting /etc/init.d/S04mdev ...
[logoview] done with Timeout...
ERROR: failed to open '/dev/sda': No medium found.
ERROR: failed to open '/dev/sda': No medium found.
error connect socket /tmp/neutrino.sock: No such file or directory
ERROR: failed to open '/dev/sda': No medium found.
ERROR: failed to open '/dev/sda': No medium found.
error connect socket /tmp/neutrino.sock: No such file or directory
starting /etc/init.d/S05mount ...
starting /etc/init.d/S50hostname ...
starting /etc/init.d/S51networking ...
Configuring network interfaces... Starting wlan0
Failed to connect to wpa_supplicant - wpa_ctrl_open: Success
Could not read interface wlan0 flags: No such device
Failed to initialize driver interface
done.
starting /etc/init.d/S52syslogd ...
starting /etc/init.d/S60autofs ...
Jan  1 00:00:30 CST-BUERO syslog.info syslogd started: BusyBox v1.30.1
 1 Jan 00:00:30 ntpdate[1540]: ntpdate 4.2.8p6@1.3265-o (1)
starting
starting /etc/init.d/S80dvdreadfs ...
starting /etc/init.d/S90inetd ...
starting /etc/init.d/S96nfsd ...
Jan  1 00:00:31 CST-BUERO daemon.notice rpc.statd[1579]: Version 2.2.1 starting
Jan  1 00:00:31 CST-BUERO daemon.notice sm-notify[1580]: Version 2.2.1 starting
Jan  1 00:00:31 CST-BUERO daemon.notice rpc.statd[1579]: Initializing NSM state
exportfs: Failed to stat /media/sda1/movies: No such file or directory
Jan  1 00:00:32 CST-BUERO daemon.notice rpc.mountd[1595]: Version 2.2.1 starting
starting /var/etc/init.d/S9T_tuxcald ...
starting /var/etc/init.d/S9T_tuxmaild ...
Jan  1 00:00:32 CST-BUERO daemon.info : starting pid 1604, tty '': '/etc/init.d/start_neutrino'

Please press Enter to activate this console. /var/plugins/operations camd_init
/var/plugins/operations cardserver_start
starte doscam
Sat Jan  1 00:00:32 CET 2000
/var/plugins/operations camd_start
/var/plugins/operations rezap
Sat Jan  1 00:00:33 CET 2000
31 Dec 12:56:22 ntpdate[1540]: step time server 130.133.1.10 offset 662734547.261081 sec
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend3: No such file or directory
MON: The POD Monitor task has started. Version = 01, Release = 00, Subrelease = 01, PID: 1640
MON: Initializing
slot->inbound_queue : 76070070
slot->outbound_queue: 7606ff18
xport_command_queue: 7606fd00
MON: Start resource providers...
MON: Starting 9 resource(s).
MON starting 9 resources finished
MON after BR_POD_mon_start_rps
RM: Resource Manager thread started. PID: 1640
XPORT: POD Transport task started. PID: 1640
LINK: POD link task started with arg=0x00000000, PID: 1640
APPINFO thread starts, PID: 1640
CA resource provider started with arg=0x00000000, PID: 1640
CP resource start, PID: 1640
CP thread get delay time 0(s)
CP: Start of initialization...
SYSTIME resource start, PID: 1640
MMI thread is started, PID: 1640
HOSTCTRL thread is started, PID: 1640
HOSTLANG_CNTY thread is started, PID: 1640
UPGRADE thread is started, PID: 1640
APPMMI thread starts, PID: 1640
XPORT: transport connection #1 set to Idle
comming in  add resource provider, rid=10041
POD timer thread PID: 1640
ciappReportModuleStatus: status 9, gCardStatus: 0
PHYS-CI+: cs_ci_init_controller called
LINK: hard reset complete.
LINK: slot #0 state = BR_POD_SLOT_NOT_INIT
comming in  add resource provider, rid=240041
SYSTIME RP: System Time main loop processing started.
comming in  add resource provider, rid=410041
comming in  add resource provider, rid=30041
CA RP: Resource Provider main loop processing started.
RM before wait for db ready, pid: 1640
RM after wait for db ready, pid: 1640
dump mbuf....
LINK: slot #0 state = BR_POD_SLOT_CARD_NOT_PRESENT
LINK: after bypass card
MON after wait event
RM: Resource Manager message processing started.
RM: recvd LINK_STATUS tag(0x42), len=8
APPMMI RP: resource provider is added
APPMMI RP: APPMMI resource provider main loop processing started.
dump mbuf....
Mbuf trace_id: 1640, aux: 0x00000000, freq: 1
ciappReportModuleStatus: status 0, gCardStatus: 0
MON: Wait for all required resource providers to sign on....
comming in  add resource provider, rid=20043
comming in  add resource provider, rid=8d1001
HOSTLANG_CNTY RP: resource provider is added
HOSTLANG_CNTY RP: HOSTLANG_CNTY resource provider main loop processing started.
CP nvram: Root certificate file is for production
RM: No host-pod interface
APPINFO RP: resource provider is added, resource ID :0x20043
APPINFO RP: APPINFO resource provider main loop processing started.
RM: close all connections on slot 0
dump mbuf....
comming in  add resource provider, rid=8e1001
UPGRADE RP: resource provider is added
UPGRADE RP: UPGRADE resource provider main loop processing started.
comming in  add resource provider, rid=200041
HOSTCTRL RP: resource provider is added
HOSTCTRL RP: HOSTCTRL resource provider main loop processing started.
comming in  add resource provider, rid=400041
MMI RP: resource provider is added
MMI RP: MMI resource provider main loop processing started.
no CICAM brand id extension.
comming in  add resource provider, rid=8c1001
RM: recvd RM_RESOURCES_CHANGED tag(0x43), len=8
CP RP: resource provider is added
CP: Resource Provider main loop processing started.
2020-12-31 12:56:30.466 [sectionsd] start
2020-12-31 12:56:30.601 [sectionsd] starting
2020-12-31 12:56:30.639 [sectionsd] timeThread::run:: starting, pid 1640 (1671562416)
2020-12-31 12:56:30.644 [sectionsd] eitThread::run:: starting, pid 1640 (1669465264)
2020-12-31 12:56:30.716 [sectionsd] cnThread::run:: starting, pid 1640 (1667368112)
2020-12-31 12:56:30.742 [sectionsd] freeSatThread::run:: starting, pid 1640 (1665270960)
2020-12-31 12:56:30.747 [sectionsd] timeThread: get DVB time ch 0x000000000000 (isOpen 1)
[ConfigFile] Unable to open file /var/tuxbox/config/bookmarks for reading.
2020-12-31 12:56:31.422 [sectionsd] timeThread: get DVB time ch 0x000000000000 rc: 8 neutrino_sets_time 0
2020-12-31 12:56:31.432 [sectionsd] SIsectionTIME::parse: TDT time: Thu Dec 31 12:56:27 2020
2020-12-31 12:56:31.436 [sectionsd] timeThread: timediff -4436229, current: 31.12.2020 12:56:31, dvb: Thu Dec 31 12:56:27 2020

2020-12-31 12:56:27.000 2020-12-31 12:56:27.005 2020-12-31 12:56:27.005 [sectionsd] freeSatThread::run:: time set: Thu Dec 31 12:56:27 2020

2020-12-31 12:56:27.006 [sectionsd] cnThread::run:: time set: 2:56:27 2020

[sectionsd] eitThread::run:: time set: Thu Dec 31 12:56:27 2020

[sectionsd] timeThread: Time set via DVB (TDT), going to sleep for 5 seconds.
2020-12-31 12:56:27.582 [sectionsd] commandserviceStopped
2020-12-31 12:56:27.702 [sectionsd] cnThread: stop eit update filter (not active)
2020-12-31 12:56:27.705 2020-12-31 12:56:27.708 [sectionsd] cnThread::shouldSleep first retry (1) -> restart demux
[sectionsd] commandserviceStopped done
2020-12-31 12:56:27.743 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
sh: you need to specify whom to kill
2020-12-31 12:56:28.089 [sectionsd] timeThread: get DVB time ch 0x00030085002b (isOpen 1)
2020-12-31 12:56:28.193 [sectionsd] addEvent: ch 00030085002b running 4 (curr) got_CN 0
2020-12-31 12:56:29.095 [sectionsd] addEvent: ch 00030085002b running 0 (next) got_CN 1
2020-12-31 12:56:29.715 [sectionsd] cnThread: eit update filter, ch 0x00030085002b, current ver 0x12  got events 3 (not active)
2020-12-31 12:56:30.102 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
2020-12-31 12:56:30.152 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
2020-12-31 12:56:30.434 [sectionsd] timeThread: get DVB time ch 0x00030085002b rc: 29 neutrino_sets_time 0
2020-12-31 12:56:30.444 [sectionsd] SIsectionTIME::parse: TOT time: Thu Dec 31 12:56:30 2020
2020-12-31 12:56:30.448 [sectionsd] timeThread: timediff -448256, current: 31.12.2020 12:56:30, dvb: Thu Dec 31 12:56:30 2020

2020-12-31 12:56:30.459 [sectionsd] difference is < 120s, using adjtime(0, -448256). oldd(0, 0)
2020-12-31 12:56:30.472 [sectionsd] timeThread: Time set via DVB (TOT), going to sleep for 1800 seconds.
[operations] rezap...
2020-12-31 12:56:35.829 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
Dec 31 12:56:50 CST-BUERO local0.info xupnpd[1814]: ./plugins/xupnpd_youtube.lua:158: bad argument #1 to 'decode' (string expected, got nil)
2020-12-31 12:56:50.862 [sectionsd] commandserviceChanged: Service change to 46712720f001c36f demux #2
2020-12-31 12:57:07.464 [sectionsd] commandserviceChanged: Service change to 4a31000400850197 demux #2
2020-12-31 12:57:30.312 [sectionsd] commandserviceChanged: Service change to 4b71000100850017 demux #2


--------------------------------------------------------------------------------
| U-Boot 2009.08-00068-g69a4049 (Dec 10 2015 - 14:51:59)               CST HDx |
|------------------------------------------------------------------------------|
| Chipset information                                                          |
| Vendor: Entropic  Type: KRONOS           Revision: B0        Fuses: 00010001 |
|------------------------------------------------------------------------------|
| Clock information                                                            |
| *** not available yet ***                                                    |
|------------------------------------------------------------------------------|
| Frontpanel information                                                       |
| Vendor: CST       Version: 3.3           Display: OLED (128 x 64 px)         |
|------------------------------------------------------------------------------|
| Memory configuration                                                         |
| Start    | End      | Type    | Description                                  |
|----------+----------+---------+----------------------------------------------|
| 00000000 | 1FFFFFFF | RAM     | System main memory bank #0 (512M)            |
| D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K x  64)      |
  *** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit               |
|------------------------------------------------------------------------------|
| Network configuration                                                        |
| MAC: LIP 6300                    address: 00-C5-5C-25-BA-B7                  |
--------------------------------------------------------------------------------

Hit any key to stop autoboot:  0

SFC read: offset 0x100000, size 0x300000
 3145728 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
   Image Name:   Coolstream Kernel (compressed)
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2981377 Bytes =  2.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
   Loading Kernel Image ... OK
OK
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.10.93 (image@server) (gcc version 6.3.1 20170109 (crosstool-NG 1) ) #1 SMP Sun Apr 15 15:27:43 CEST 2018
[    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7), cr=10c53c7d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: Entropic Kronos STB Platform with FDT, model: CoolStream HD2 Kronos STB
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] Early platform io descriptors mapping...
[    0.000000] PERCPU: Embedded 7 pages/cpu @80da8000 s5952 r8192 d14528 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: noinitrd console=ttyS0,115200n8 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1) root=mtd:root0 rootfstype=jffs2 rw
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 512MB = 512MB total
[    0.000000] Memory: 247144k/247144k available, 277144k reserved, 0K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
[    0.000000]     lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
[    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
[    0.0000

BusyBox v1.30.1 (2019-06-22 15:09:50 CEST) built-in shell (ash)

Dec 31 12:57:51 CST-BUERO daemon.info : starting pid 1605, tty '': '-/bin/sh'
CST-BUERO:/#
CST-BUERO:/# -------------------------------------------------------------------
-------------
-/bin/sh: --------------------------------------------------------------------------------: not found
CST-BUERO:/# | U-Boot 2009.08-00068-g69a4049 (Dec 10 2015 - 14:51:59)
    CST HDx |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# |------------------------------------------------------------------
------------|
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# | Chipset information
            |
> | Vendor: Entropic  Type: KRONOS           Revision: B0        Fuses: 00010001
 |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# |------------------------------------------------------------------
------------|
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# | Clock information
            |
> | *** not available yet ***
 |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# |------------------------------------------------------------------
------------|
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# | Frontpanel information
            |
> | Vendor: CST       Version: 3.3           Display: OLED (128 x 64 px)
 |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# |------------------------------------------------------------------
------------|
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# | Memory configuration
            |
> | Start    | End      | Type    | Description
 |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# |----------+----------+---------+----------------------------------
------------|
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# | 00000000 | 1FFFFFFF | RAM     | System main memory bank #0 (512M)
            |
-/bin/sh: 00000000: not found
-/bin/sh: 1FFFFFFF: not found
-/bin/sh: -: not found
-/bin/sh: RAM: not found
-/bin/sh: System: not found
CST-BUERO:/# | D0000000 | D03FFFFF | S-FLASH | Eon Silicon EN25Q32 (  4M /  64K
x  64)      |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/#   *** Warning - bad CRC or SFC, using default environment
-/bin/sh: bin: not found
CST-BUERO:/# | 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit
            |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# |------------------------------------------------------------------
------------|
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# | Network configuration
            |
> | MAC: LIP 6300                    address: 00-C5-5C-25-BA-B7
 |
-/bin/sh: syntax error: unexpected "|"
CST-BUERO:/# -------------------------------------------------------------------
-------------
-/bin/sh: --------------------------------------------------------------------------------: not found
CST-BUERO:/#
CST-BUERO:/# Hit any key to stop autoboot:  0
-/bin/sh: Hit: not found
CST-BUERO:/#
CST-BUERO:/# SFC read: offset 0x100000, size 0x300000
-/bin/sh: SFC: not found
CST-BUERO:/#  3145728 bytes read: OK
-/bin/sh: 3145728: not found
CST-BUERO:/# ## Booting kernel from Legacy Image at 01000000 ...
CST-BUERO:/#    Image Name:   Coolstream Kernel (compressed)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/#    Image Type:   ARM Linux Kernel Image (uncompressed)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/#    Data Size:    2981377 Bytes =  2.8 MB
-/bin/sh: Data: not found
CST-BUERO:/#    Load Address: 00008000
-/bin/sh: Load: not found
CST-BUERO:/#    Entry Point:  00008000
-/bin/sh: Entry: not found
CST-BUERO:/#    Verifying Checksum ... OK
-/bin/sh: Verifying: not found
CST-BUERO:/#    Loading Kernel Image ... OK
-/bin/sh: Loading: not found
CST-BUERO:/# OK
-/bin/sh: OK: not found
CST-BUERO:/# Uncompressing Linux... done, booting the kernel.
-/bin/sh: Uncompressing: not found
CST-BUERO:/# [    0.000000] Booting Linux on physical CPU 0x0
sh: missing ]
CST-BUERO:/# [    0.000000] Initializing cgroup subsys cpuset
sh: missing ]
CST-BUERO:/# [    0.000000] Linux version 3.10.93 (image@server) (gcc version 6.
3.1 20170109 (crosstool-NG 1) ) #1 SMP Sun Apr 15 15:27:43 CEST 2018
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000] CPU: ARMv7 Processor [412fc09a] revision 10 (ARMv7),
 cr=10c53c7d
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasi
ng instruction cache
sh: missing ]
CST-BUERO:/# [    0.000000] Machine: Entropic Kronos STB Platform with FDT, mode
l: CoolStream HD2 Kronos STB
sh: missing ]
CST-BUERO:/# [    0.000000] Memory policy: ECC disabled, Data cache writealloc
sh: missing ]
CST-BUERO:/# [    0.000000] Early platform io descriptors mapping...
sh: missing ]
CST-BUERO:/# [    0.000000] PERCPU: Embedded 7 pages/cpu @80da8000 s5952 r8192 d
14528 u32768
sh: missing ]
CST-BUERO:/# [    0.000000] Built 1 zonelists in Zone order, mobility grouping o
n.  Total pages: 130048
sh: missing ]
CST-BUERO:/# [    0.000000] Kernel command line: noinitrd console=ttyS0,115200n8
 mtdparts=e0632000.flash_sfc:256k@0k(uldr),512k@256k(u-boot),128k@768k(env),128k
@896k(spare),-(kernel);e0631000.flash_nand:256m@0k(root0),32m@256m(var),-(root1)
 root=mtd:root0 rootfstype=jffs2 rw
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000] Dentry cache hash table entries: 65536 (order: 6, 26
2144 bytes)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131
072 bytes)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000] Memory: 512MB = 512MB total
sh: missing ]
CST-BUERO:/# [    0.000000] Memory: 247144k/247144k available, 277144k reserved,
 0K highmem
sh: missing ]
CST-BUERO:/# [    0.000000] Virtual kernel memory layout:
sh: missing ]
CST-BUERO:/# [    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]     vmalloc : 0xa0800000 - 0xff000000   (1512 MB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]     lowmem  : 0x80000000 - 0xa0000000   ( 512 MB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]     modules : 0x7f000000 - 0x80000000   (  16 MB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]       .text : 0x80008000 - 0x806584f8   (6466 kB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]       .init : 0x80659000 - 0x80687740   ( 186 kB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]       .data : 0x80688000 - 0x806c8e60   ( 260 kB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000]        .bss : 0x806c8e60 - 0x806e32 ( 105 kB)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, N
odes=1
sh: missing ]
CST-BUERO:/# [    0.000000] Hierarchical RCU imple    0.000000]  RCU debugfs-bas
ed tracing is enabled.
sh: missing ]
CST-BUERO:/# [    0.000000]  Additional per-CPU info printed with stalls.
sh: missing ]
CST-BUERO:/# [    0.000000]  RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1
.
sh: missing ]
CST-BUERO:/# [    0.000000] NR_IRQS:350
sh: missing ]
CST-BUERO:/# [    0.000000] GIC CPU mask not found - kernel will fail to boot.
sh: missing ]
CST-BUERO:/# [    0.000000] GInot found - kernel will fail to boot.
sh: missing ]
CST-BUERO:/# [    0.000000] Cortex A9 frequency at 600 MHz
sh: missing ]
CST-BUERO:/# [    0.000000] Initializing Cortex A9lobal Timer at Vir:0xFEA00200,
 using, at Freq:300 MHz
sh: missing ]
CST-BUERO:/# [    0.000000] sched_clock: 32 bits at 300MHz, resolution 3ns, wrap
s every 14316ms
sh: missing ]
CST-BUERO:/# [    0.000000] smp_twd: clock not found -2
sh: missing ]
CST-BUERO:/# [    0.000000] Console: colour dummy device 80x30
sh: missing ]
CST-BUERO:/# [    0.000000] console [ttyS0] enabled
sh: missing ]
CST-BUERO:/# [    0.249870] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984
256)
-/bin/sh:     0.531347] usbcore: registered new interface driver usbfs
[    0.536927] usbcore: registered new interface driver hub
[    0.542583] usbcore: registered new device driver usb
[    0.548014] pps_core: LinuxPPS API ver. 1 registered
[    0.552941] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.562233] PTP clock support registered
[    0.567795] cfg80211: Calling CRDA to update world regulatory domain
[    0.575590] Switching to clocksource arm_global_timer
[    0.599398] NET: Registered protocol family 2
[    0.604702] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[    0.611789] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
[    0.618198] TCP: Hash tables configured (established 4096 bind 4096)
[    0.624548] TCP: reno registered
[    0.627694] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.633544] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.640018] NET: Registered protocol family 1
[    0.644798] RPC: Registered named UNIX socket transport module.
[    0.650641] RPC: Registered udp transport module.
[    0.655280] RPC: Registered tcp transport module.
[    0.659946] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.666514] PM: STB Platform power mgmt initialization.
[    0.797170] NFS: Registering the id_resolver key type
[    0.802256] Key type id_resolver registered
[    0.806334] Key type id_legacy registered
[    0.810360] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    0.816724] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    0.824706] msgmni has been set to 482
[    0.829754] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[    0.837119] io scheduler noop registered
[    0.840977] io scheduler deadline registered
[    0.845841] io scheduler cfq registered (default)
[    0.851212] e06b2000.serial: ttyS0 at MMIO 0xe06b2000 (irq = 47) is a uart-ip3106
[    0.865619] loop: module loaded
[    0.869733] ahci-stb e0638000.sata: unable to find phy
[    0.874835] SATA: Enable mpll_ss_en (rd_val=0x571185, wr_val=0x5711a5)
[    0.881269] SATA: Enable rx_term_en0 (rd_val=0x277, wr_val=0x277)
[    0.887335] ahci-stb e0638000.sata: SSS flag set, parallel bus scan disabled
[    0.894345] ahci-stb e0638000.sata: AHCI 0001.0300 32 slots 1 ports 3 Gbps 0x1 impl platform mode
[    0.903131] ahci-stb e0638000.sata: flags: ncq sntf stag pm led clo only pmp pio slum part ccc apst
[    0.912602] ata4294967295: SATA PHY offline
[    0.917624] scsi0 : ahci_platform
[    0.921591] ata1: SATA max UDMA/133 mmio [mem 0xe0638000-0xe0638fff] port 0x100 irq 39
[    0.931064] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
[    0.943464] Bad block table found at page 262080, version 0x01
[    0.949976] Bad block table found at page 262016, version 0x01
[    0.956233] nand_read_bbt: bad block at 0x00001cf60000
[   syntax error: unexpected "("
CST-BUERO:/# [    0.292758] pid_max: default: 32768 minimum: 301
sh: missing ]
CST-BUERO:/# [    0.297559] Mount-cache hash table entries: 512
sh: missing ]
CST-BUERO:/# [    0.303981] CPU: Testing write buffer coherency: ok
sh: missing ]
CST-BUERO:/# [    0.309063] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
sh: missing ]
CST-BUERO:/# [    0.314686] Setting up static identity map for 0x803c47a0 - 0x80
3c47f8
sh: missing ]
CST-BUERO:/# [    0.321215] L310 cache controller enabled
sh: missing ]
CST-BUERO:/# [    0.325132] l2x0: 8 ways, CACHE_ID 0x410004c7, AUX_CTRL 0x324210
01, Cache size: 131072 B
sh: missing ]
CST-BUERO:/# [    0.333758] Brought up 1 CPUs
sh: missing ]
CST-BUERO:/# [    0.336632] SMP: Total of 1 processors activated (1196.85 BogoMI
PS).
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.342954] CPU: All CPU(s) started in SVC mode.
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.348217] devtmpfs: initialized
sh: missing ]
CST-BUERO:/# [    0.356569] NET: Registered protocol family 16
sh: missing ]
CST-BUERO:/# [    0.361679] DMA: preallocated 256 KiB pool for atomic coherent a
llocations
sh: missing ]
CST-BUERO:/# [    0.475065] GMAC0: active interface is 1
sh: missing ]
CST-BUERO:/# [    0.479061] ChipID=0x1000 ChipRevID=0x100
sh: missing ]
CST-BUERO:/# [    0.483152] nx_dmac: Registered with 8 channels
sh: missing ]
CST-BUERO:/# [    0.509731] bio: create slab <bio-0> at 0
-/bin/sh: can't open bio-0: no such file
CST-BUERO:/# [    0.515228] GPIO: base febab000 (phys e06ab000)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.519819] GPIO: base feb69000 (phys e0669000)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.526207] SCSI subsystem initialized
sh: missing ]
CST-BUERO:/# [    0.531347] usbcore: registered new interface driver usbfs
sh: missing ]
CST-BUERO:/# [    0.536927] usbcore: registered new interface driver hub
sh: missing ]
CST-BUERO:/# [    0.542583] usbcore: registered new device driver usb
sh: missing ]
CST-BUERO:/# [    0.548014] pps_core: LinuxPPS API ver. 1 registered
sh: missing ]
CST-BUERO:/# [    0.552941] pps_core: Software ver. 5.3.6 - Copyright 2005-2007
Rodolfo Giometti <giometti@linux.it>
-/bin/sh: syntax error: unexpected newline
CST-BUERO:/# [    0.562233] PTP clock support registered
sh: missing ]
CST-BUERO:/# [    0.567795] cfg80211: Calling CRDA to update world regulatory do
main
sh: missing ]
CST-BUERO:/# [    0.575590] Switching to clocksource arm_global_timer
sh: missing ]
CST-BUERO:/# [    0.599398] NET: Registered protocol family 2
sh: missing ]
CST-BUERO:/# [    0.604702] TCP established hash table entries: 4096 (order: 3,
32768 bytes)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.611789] TCP bind hash table entries: 4096 (order: 3, 32768 b
ytes)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.618198] TCP: Hash tables configured (established 4096 bind 4
096)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.624548] TCP: reno registered
sh: missing ]
CST-BUERO:/# [    0.627694] UDP hash table entries: 256 (order: 1, 8192 bytes)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.633544] UDP-Lite hash table entries: 256 (order: 1, 8192 byt
es)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.640018] NET: Registered protocol family 1
sh: missing ]
CST-BUERO:/# [    0.644798] RPC: Registered named UNIX socket transport module.
sh: missing ]
CST-BUERO:/# [    0.650641] RPC: Registered udp transport module.
sh: missing ]
CST-BUERO:/# [    0.655280] RPC: Registered tcp transport module.
sh: missing ]
CST-BUERO:/# [    0.659946] RPC: Registered tcp NFSv4.1 backchannel transport mo
dule.
sh: missing ]
CST-BUERO:/# [    0.666514] PM: STB Platform power mgmt initialization.
sh: missing ]
CST-BUERO:/# [    0.797170] NFS: Registering the id_resolver key type
sh: missing ]
CST-BUERO:/# [    0.802256] Key type id_resolver registered
sh: missing ]
CST-BUERO:/# [    0.806334] Key type id_legacy registered
sh: missing ]
CST-BUERO:/# [    0.810360] Installing knfsd (copyright (C) 1996 okir@monad.swb.
de).
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.816724] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 R
ed Hat, Inc.
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.824706] msgmni has been set to 482
sh: missing ]
CST-BUERO:/# [    0.829754] Block layer SCSI generic (bsg) driver version 0.4 lo
aded (major 252)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.837119] io scheduler noop registered
sh: missing ]
CST-BUERO:/# [    0.840977] io scheduler deadline registered
sh: missing ]
CST-BUERO:/# [    0.845841] io scheduler cfq registered (default)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.851212] e06b2000.serial: ttyS0 at MMIO 0xe06b2000 (irq = 47)
 is a uart-ip3106
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.865619] loop: module loaded
sh: missing ]
CST-BUERO:/# [    0.869733] ahci-stb e0638000.sata: unable to find phy
sh: missing ]
CST-BUERO:/# [    0.874835] SATA: Enable mpll_ss_en (rd_val=0x571185, wr_val=0x5
711a5)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.881269] SATA: Enable rx_term_en0 (rd_val=0x277, wr_val=0x277
)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.887335] ahci-stb e0638000.sata: SSS flag set, parallel bus s
can disabled
sh: missing ]
CST-BUERO:/# [    0.894345] ahci-stb e0638000.sata: AHCI 0001.0300 32 slots 1 po
rts 3 Gbps 0x1 impl platform mode
sh: missing ]
CST-BUERO:/# [    0.903131] ahci-stb e0638000.sata: flags: ncq sntf stag pm led
clo only pmp pio slum part ccc apst
sh: missing ]
CST-BUERO:/# [    0.912602] ata4294967295: SATA PHY offline
sh: missing ]
CST-BUERO:/# [    0.917624] scsi0 : ahci_platform
sh: missing ]
CST-BUERO:/# [    0.921591] ata1: SATA max UDMA/133 mmio [mem 0xe0638000-0xe0638
fff] port 0x100 irq 39
sh: missing ]
CST-BUERO:/# [    0.931064] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (T
oshiba NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    0.943464] Bad block table found at page 262080, version 0x01
sh: missing ]
CST-BUERO:/# [    0.949976] Bad block table found at page 262016, version 0x01
sh: missing ]
CST-BUERO:/# [    0.956233] nand_read_bbt: bad block at 0x00001cf60000
sh: missing ]
CST-BUERO:/# [    0.961298] nand_read_bbt: bad block at 0x00001cfa0000
sh: missing ]
CST-BUERO:/# [    0.966421] 3 cmdlinepart partitions found on MTD device e063100
0.flash_nand
sh: missing ]
CST-BUERO:/# [    0.973375] Creating 3 MTD partitions on "e0631000.flash_nand":
sh: missing ]
CST-BUERO:/# [    0.979243] 0x000000000000-0x000010000000 : "root0"
sh: missing ]
CST-BUERO:/# [    0.985791] 0x000010000000-0x000012000000 : "var"
sh: missing ]
CST-BUERO:/# [    0.991886] 0x000012000000-0x000020000000 : "root1"
sh: missing ]
CST-BUERO:/# [    1.000227] JEDEC ID = 0x1c3016 , Extended Device ID = 0x1c30
sh: missing ]
CST-BUERO:/# [    1.005966] nx_sfc e0632000.flash_sfc: en25q32 (4096 Kbytes)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.011608] 5 cmdlinepart partitions found on MTD device e063200
0.flash_sfc
sh: missing ]
CST-BUERO:/# [    1.018482] Creating 5 MTD partitions on "e0632000.flash_sfc":
sh: missing ]
CST-BUERO:/# [    1.024296] 0x000000000000-0x000000040000 : "uldr"
sh: missing ]
oad Engine supported (type 2)
[    1.096602]  TX Checksum insertion supported
[    1.100842]  Wake-Up On Lan supported
[    1.104509]  Enable RX Mitigation via HW Watchdog Timer
[    1.124496] libphy: stmmac: probed
[    1.127809] eth0: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) active
[    1.134167] eth0: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
[    1.139815] eth0: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
[    1.145529] eth0: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
[    1.151233] eth0: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
[    1.156922] eth0: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
[    1.162632] eth0: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
[    1.168327] eth0: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
[    1.174036] eth0: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
[    1.179731] eth0: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
[    1.185441] eth0: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
[    1.191228] eth0: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
[    1.197011] eth0: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
[    1.202806] eth0: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
[    1.208589] eth0: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
[    1.214384] eth0: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
[    1.220171] eth0: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
[    1.225955] eth0: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
[    1.231749] eth0: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
[    1.237533] eth0: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
[    1.243328] eth0: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
[    1.249110] eth0: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
[    1.254905] eth0: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
[    1.260694] eth0: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
[    1.266477] eth0: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
[    1.272271] eth0: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
[    1.278054] eth0: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
[    1.283849] eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
[    1.289632] eth0: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
[    1.295426] eth0: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
[    1.301215] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
[    1.306998] eth0: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
[    1.313040] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.319455] ehci-platform: EHCI generic platform driver
[    1.324933] ehci-platform e066c000.usb: EHCI Host Controller
[    1.330565] ehci-platform e066c000.usb: new USB bus registered, assigned bus number 1
[    1.338385] ehci-platform e066c000.usb: irq 93, io mem 0xe066c000
[    1.360090] ehci-platform e066c000.usb: USB 2.0 started, EHCI 1.00
[    1.366243] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.372958] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.380115] usb usb1: Product: EHCI Host Controller
[    1.384932] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
[    1.390394] usb usb1: SerialNumber: e066c000.usb
[    1.395871] hub 1-0:1.0: USB hub found
[    1.399543] hub 1-0:1.0: 1 port detected
[    1.403717] ehci-platform e066d000.usb: EHCI Host Controller
[    1.409290] ehci-platform e066d000.usb: new USB bus registered, assigned bus number 2
[    1.417202] ehci-platform e066d000.usb: irq 94, io mem 0xe066d000
[    1.423256] ata1: SATA PHY offline
[    1.426572] ata1: SATA linkCST-BUERO:/# [    1.030685] 0x000000040000-0x0000000c0000 : "u-boot"
sh: missing ]
CST-BUERO:/# [    1.036977] 0x0000000c0000-0x0000000e0000 : "env"
sh: missing ]
CST-BUERO:/# [    1.043102] 0x0000000e0000-0x000000100000 : "spare"
sh: missing ]
CST-BUERO:/# [    1.049350] 0x000000100000-0x000000400000 : "kernel"
sh: missing ]
CST-BUERO:/# [    1.056400] tun: Universal TUN/TAP device driver, 1.6
sh: missing ]
CST-BUERO:/# [    1.061421] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.co
m>
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.068063]  DWMAC1000
sh: missing ]
CST-BUERO:/# [    1.070366] stmmac - user ID: 0x36, Synopsys ID: 0x36
sh: missing ]
CST-BUERO:/# [    1.075347]  Ring mode enabled
sh: missing ]
CST-BUERO:/# [    1.078372]  DMA HW capability register supported
sh: missing ]
CST-BUERO:/# [    1.082882]  Enhanced/Alternate descriptors
sh: missing ]
CST-BUERO:/# [    1.087184]  Enabled extended descriptors
sh: missing ]
CST-BUERO:/# [    1.091170]  RX Checksum Offload Engine supported (type 2)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.096602]  TX Checksum insertion supported
sh: missing ]
CST-BUERO:/# [    1.100842]  Wake-Up On Lan supported
sh: missing ]
CST-BUERO:/# [    1.104509]  Enable RX Mitigation via HW Watchdog Timer
sh: missing ]
CST-BUERO:/# [    1.124496] libphy: stmmac: probed
sh: missing ]
CST-BUERO:/# [    1.127809] eth0: PHY ID 0293c412 at 0 IRQ POLL (stmmac-0:00) ac
tive
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.134167] eth0: PHY ID 00000000 at 1 IRQ POLL (stmmac-0:01)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.139815] eth0: PHY ID 00000000 at 2 IRQ POLL (stmmac-0:02)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.145529] eth0: PHY ID 00000000 at 3 IRQ POLL (stmmac-0:03)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.151233] eth0: PHY ID 00000000 at 4 IRQ POLL (stmmac-0:04)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.156922] eth0: PHY ID 00000000 at 5 IRQ POLL (stmmac-0:05)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.162632] eth0: PHY ID 00000000 at 6 IRQ POLL (stmmac-0:06)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.168327] eth0: PHY ID 00000000 at 7 IRQ POLL (stmmac-0:07)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.174036] eth0: PHY ID 00000000 at 8 IRQ POLL (stmmac-0:08)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.179731] eth0: PHY ID 00000000 at 9 IRQ POLL (stmmac-0:09)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.185441] eth0: PHY ID 00000000 at 10 IRQ POLL (stmmac-0:0a)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.191228] eth0: PHY ID 00000000 at 11 IRQ POLL (stmmac-0:0b)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.197011] eth0: PHY ID 00000000 at 12 IRQ POLL (stmmac-0:0c)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.202806] eth0: PHY ID 00000000 at 13 IRQ POLL (stmmac-0:0d)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.208589] eth0: PHY ID 00000000 at 14 IRQ POLL (stmmac-0:0e)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.214384] eth0: PHY ID 00000000 at 15 IRQ POLL (stmmac-0:0f)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.220171] eth0: PHY ID 00000000 at 16 IRQ POLL (stmmac-0:10)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.225955] eth0: PHY ID 00000000 at 17 IRQ POLL (stmmac-0:11)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.231749] eth0: PHY ID 00000000 at 18 IRQ POLL (stmmac-0:12)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.237533] eth0: PHY ID 00000000 at 19 IRQ POLL (stmmac-0:13)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.243328] eth0: PHY ID 00000000 at 20 IRQ POLL (stmmac-0:14)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.249110] eth0: PHY ID 00000000 at 21 IRQ POLL (stmmac-0:15)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.254905] eth0: PHY ID 00000000 at 22 IRQ POLL (stmmac-0:16)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.260694] eth0: PHY ID 00000000 at 23 IRQ POLL (stmmac-0:17)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.266477] eth0: PHY ID 00000000 at 24 IRQ POLL (stmmac-0:18)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.272271] eth0: PHY ID 00000000 at 25 IRQ POLL (stmmac-0:19)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.278054] eth0: PHY ID 00000000 at 26 IRQ POLL (stmmac-0:1a)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.283849] eth0: PHY ID 00000000 at 27 IRQ POLL (stmmac-0:1b)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.289632] eth0: PHY ID 00000000 at 28 IRQ POLL (stmmac-0:1c)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.295426] eth0: PHY ID 00000000 at 29 IRQ POLL (stmmac-0:1d)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.301215] eth0: PHY ID 00000000 at 30 IRQ POLL (stmmac-0:1e)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.306998] eth0: PHY ID 00000000 at 31 IRQ POLL (stmmac-0:1f)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.313040] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
Driver
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.319455] ehci-platform: EHCI generic platform driver
sh: missing ]
CST-BUERO:/# [    1.324933] ehci-platform e066c000.usb: EHCI Host Controller
sh: missing ]
CST-BUERO:/# [    1.330565] ehci-platform e066c000.usb: new USB bus registered,
assigned bus number 1
sh: missing ]
CST-BUERO:/# [    1.338385] ehci-platform e066c000.usb: irq 93, io mem 0xe066c00
0
sh: missing ]
CST-BUERO:/# [    1.360090] ehci-platform e066c000.usb: USB 2.0 started, EHCI 1.
00
sh: missing ]
CST-BUERO:/# [    1.366243] usb usb1: New USB device found, idVendor=1d6b, idPro
duct=0002
sh: missing ]
CST-BUERO:/# [    1.372958] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
sh: missing ]
CST-BUERO:/# [    1.380115] usb usb1: Product: EHCI Host Controller
sh: missing ]
CST-BUERO:/# [    1.384932] usb usb1: Manufacturer: Linux 3.10.93 ehci_hcd
sh: missing ]
CST-BUERO:/# [    1.390394] usb usb1: SerialNumber: e066c000.usb
sh: missing ]
CST-BUERO:/# [    1.395871] hub 1-0:1.0: USB hub found
sh: missing ]
CST-BUERO:/# [    1.399543] hub 1-0:1.0: 1 port detected
sh: missing ]
CST-BUERO:/# [    1.403717] ehci-platform e066d000.usb: EHCI Host Controller
sh: missing ]
CST-BUERO:/# [    1.409290] ehci-platform e066d000.usb: new USB bus registered,
assigned bus number 2
sh: missing ]
CST-BUERO:/# [    1.417202] ehci-platform e066d000.usb: irq 94, io mem 0xe066d00
0
sh: missing ]
CST-BUERO:/# [    1.423256] ata1: SATA PHY offline
sh: missing ]
CST-BUERO:/# [    1.426572] ata1: SATA link down (SStatus 0 SControl 300)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    1.440079] ehci-platform e066d000.usb: USB 2.0 started, EHCI 1.
00
sh: missing ]
CST-BUERO:/# [    1.446232] usb usb2: New USB device found, idVendor=1d6b, idPro
duct=0002
sh: missing ]
CST-BUERO:/# [    1.452946] usb usb2: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
sh: missing ]
CST-BUERO:/# [    1.460101] usb usb2: Product: EHCI Host Controller
sh: missing ]
CST-BUERO:/# [    1.464922] usb usb2: Manufacturer: Linux 3.10.93 ehci_hcd
sh: missing ]
CST-BUERO:/# [    1.470375] usb usb2: SerialNumber: e066d000.usb
sh: missing ]
CST-BUERO:/# [    1.475761] hub 2-0:1.0: USB hub found
sh: missing ]
CST-BUERO:/# [    1.479436] hub 2-0:1.0: 1 port detected
sh: missing ]
CST-BUERO:/# [    1.484062] usbcore: registered new interface driver usb-storage
sh: missing ]
CST-BUERO:/# [    1.490466] usbcore: registered new interface driver usbserial
sh: missing ]
CST-BUERO:/# [    1.497766] usbcore: registered new interface driver usbhid
sh: missing ]
ber=0
[    1.895604] usb 1-1: Product: USB2.0 Hub
[    1.900898] hub 1-1:1.0: USB hub found
[    1.904888] hub 1-1:1.0: 4 ports detected
[    3.500065] usb 2-1: new high-speed USB device number 2 using ehci-platform
[    4.403938] usb 2-1: New USB device found, idVendor=174c, idProduct=5136
[    4.410576] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[    4.417616] usb 2-1: Product: AS2105
[    4.421173] usb 2-1: Manufacturer: ASMedia
[    4.425220] usb 2-1: SerialNumber: 00000000000000000000
[    4.434240] usb-storage 2-1:1.0: USB Mass Storage device detected
[    4.440522] scsi1 : usb-storage 2-1:1.0
[    5.441066] scsi 1:0:0:0: Direct-Access     ASMT     2105             0    PQ: 0 ANSI: 6
[    5.451074] sd 1:0:0:0: Attached scsi generic sg0 type 0
[    5.459263] sd 1:0:0:0: [sda] Attached SCSI removable disk
[    7.557428] VFS: Mounted root (jffs2 filesystem) on device 31:0.
[    7.565107] devtmpfs: mounted
[    7.568277] Freeing unused kernel memory: 184K (80659000 - 80687000)
init started: BusyBox v1.30.1 (2019-06-22 15:09:50 CEST)
[    8.461771] NET: Registered protocol family 10
try to mount /dev/mtdblock1 to /var
starting /etc/init.d/S02loadmodules ...
Sat Jan  1 00:00:00 CET 2000
Creating device node for cs_display
Running insmod now .......
Driver modules loaded, please start the app now...
Creating device node for KAL
Creating device node for notifyq
Creating device node for platform
Creating device node for content
Creating device node for standby
Creating device node for video
Creating device node for audio
Creating device node for pvr
Creating device node for ci
Creating device node for cs_control
Creating device node for cs_ir
Creating device node for fb
starting /etc/init.d/S04mdev ...
[logoview] done with Timeout...
ERROR: failed to open '/dev/sda': No medium found.
ERROR: failed to open '/dev/sda': No medium found.
error connect socket /tmp/neutrino.sock: No such file or directory
ERROR: failed to open '/dev/sda': No medium found.
ERROR: failed to open '/dev/sda': No medium found.
error connect socket /tmp/neutrino.sock: No such file or directory
starting /etc/init.d/S05mount ...
starting /etc/init.d/S50hostname ...
starting /etc/init.d/S51networking ...
Configuring network interfaces... Starting wlan0
Failed to connect to wpa_supplicant - wpa_ctrl_open: Success
Could not read interface wlan0 flags: No such device
Failed to initialize driver interface
done.
starting /etc/init.d/S52syslogd ...
starting /etc/init.d/S60autofs ...
Jan  1 00:00:30 CST-BUERO syslog.info syslogd started: BusyBox v1.30.1
 1 Jan 00:00:30 ntpdate[1540]: ntpdate 4.2.8p6@1.3265-o (1)
starting
starting /etc/init.d/S80dvdreadfs ...
starting /etc/init.d/S90inetd ...
starting /etc/init.d/S96nfsd ...
Jan  1 00:00:31 CST-BUERO daemon.notice rpc.statd[1579]: Version 2.2.1 starting
Jan  1 00:00:31 CST-BUERO daemon.notice sm-notify[1580]: Version 2.2.1 starting
Jan  1 00:00:31 CST-BUERO daemon.notice rpc.statd[1579]: Initializing NSM state
exportfs: Failed to stat /media/sda1/movies: No such file or directory
Jan  1 00:00:32 CST-BUERO daemon.notice rpc.mountd[1595]: Version 2.2.1 starting
starting /var/etc/init.d/S9T_tuxcald ...
starting /var/etc/init.d/S9T_tuxmaild ...
Jan  1 00:00:32 CST-BUERO daemon.info : starting pid 1604, tty '': '/etc/init.d/start_neutrino'

Please press Enter to activate this console. /var/plugins/operations camd_init
/var/plugins/operations cardserver_start
starte doscam
Sat Jan  CST-BUERO:/# [    1.503308] usbhid: USB HID core driver

sh: missing ]
CST-BUERO:/# [    1.507301] TCP: cubic registered
sh: missing ]
CST-BUERO:/# [    1.510544] NET: Registered protocol family 17
sh: missing ]
CST-BUERO:/# [    1.515357] Key type dns_resolver registered
sh: missing ]
CST-BUERO:/# [    1.519637] VFP support v0.3: implementor 41 architecture 3 part
 30 variant 9 rev 3
sh: missing ]
CST-BUERO:/# [    1.527172] ThumbEE CPU extension supported.
sh: missing ]
CST-BUERO:/# [    1.532454] ### dt-test ### No testcase data in device tree; not
 running tests
sh: missing ]
CST-BUERO:/# [    1.730081] usb 1-1: new high-speed USB device number 2 using eh
ci-platform
sh: missing ]
CST-BUERO:/# [    1.881891] usb 1-1: New USB device found, idVendor=05e3, idProd
uct=0608
sh: missing ]
CST-BUERO:/# [    1.888507] usb 1-1: New USB device strings: Mfr=0, Product=1, S
erialNumber=0
sh: missing ]
CST-BUERO:/# [    1.895604] usb 1-1: Product: USB2.0 Hub
sh: missing ]
CST-BUERO:/# [    1.900898] hub 1-1:1.0: USB hub found
sh: missing ]
CST-BUERO:/# [    1.904888] hub 1-1:1.0: 4 ports detected
sh: missing ]
CST-BUERO:/# [    3.500065] usb 2-1: new high-speed USB device number 2 using eh
ci-platform
sh: missing ]
CST-BUERO:/# [    4.403938] usb 2-1: New USB device found, idVendor=174c, idProd
uct=5136
sh: missing ]
CST-BUERO:/# [    4.410576] usb 2-1: New USB device strings: Mfr=2, Product=3, S
erialNumber=1
sh: missing ]
CST-BUERO:/# [    4.417616] usb 2-1: Product: AS2105
sh: missing ]
CST-BUERO:/# [    4.421173] usb 2-1: Manufacturer: ASMedia
sh: missing ]
CST-BUERO:/# [    4.425220] usb 2-1: SerialNumber: 00000000000000000000
sh: missing ]
CST-BUERO:/# [    4.434240] usb-storage 2-1:1.0: USB Mass Storage device detecte
d
sh: missing ]
CST-BUERO:/# [    4.440522] scsi1 : usb-storage 2-1:1.0
sh: missing ]
CST-BUERO:/# [    5.441066] scsi 1:0:0:0: Direct-Access     ASMT     2105
      0    PQ: 0 ANSI: 6
sh: missing ]
CST-BUERO:/# [    5.451074] sd 1:0:0:0: Attached scsi generic sg0 type 0
sh: missing ]
CST-BUERO:/# [    5.459263] sd 1:0:0:0: [sda] Attached SCSI removable disk
sh: missing ]
CST-BUERO:/# [    7.557428] VFS: Mounted root (jffs2 filesystem) on device 31:0.
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    7.565107] devtmpfs: mounted
sh: missing ]
CST-BUERO:/# [    7.568277] Freeing unused kernel memory: 184K (80659000 - 80687
000)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# init started: BusyBox v1.30.1 (2019-06-22 15:09:50 CEST)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [    8.461771] NET: Registered protocol family 10
sh: missing ]
CST-BUERO:/# try to mount /dev/mtdblock1 to /var
-/bin/sh: try: not found
CST-BUERO:/# starting /etc/init.d/S02loadmodules ...
-/bin/sh: starting: not found
CST-BUERO:/# Sat Jan  1 00:00:00 CET 2000
-/bin/sh: Sat: not found
CST-BUERO:/# Creating device node for cs_display
-/bin/sh: Creating: not found
CST-BUERO:/# Running insmod now .......
-/bin/sh: Running: not found
CST-BUERO:/# Driver modules loaded, please start the app now...
-/bin/sh: Driver: not found
CST-BUERO:/# Creating device node for KAL
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for notifyq
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for platform
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for content
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for standby
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for video
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for audio
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for pvr
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for ci
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for cs_control
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for cs_ir
-/bin/sh: Creating: not found
CST-BUERO:/# Creating device node for fb
-/bin/sh: Creating: not found
CST-BUERO:/# starting /etc/init.d/S04mdev ...
-/bin/sh: starting: not found
CST-BUERO:/# [logoview] done with Timeout...
-/bin/sh: [logoview]: not found
CST-BUERO:/# ERROR: failed to open '/dev/sda': No medium found.
-/bin/sh: ERROR:: not found
CST-BUERO:/# ERROR: failed to open '/dev/sda': No medium found.
-/bin/sh: ERROR:: not found
CST-BUERO:/# error connect socket /tmp/neutrino.sock: No such file or directory
-/bin/sh: error: not found
CST-BUERO:/# ERROR: failed to open '/dev/sda': No medium found.
-/bin/sh: ERROR:: not found
CST-BUERO:/# ERROR: failed to open '/dev/sda': No medium found.
-/bin/sh: ERROR:: not found
CST-BUERO:/# error connect socket /tmp/neutrino.sock: No such file or directory
-/bin/sh: error: not found
CST-BUERO:/# starting /etc/init.d/S05mount ...
-/bin/sh: starting: not found
CST-BUERO:/# starting /etc/init.d/S50hostname ...
-/bin/sh: starting: not found
CST-BUERO:/# starting /etc/init.d/S51networking ...
-/bin/sh: starting: not found
CST-BUERO:/# Configuring network interfaces... Starting wlan0
-/bin/sh: Configuring: not found
CST-BUERO:/# Failed to connect to wpa_supplicant - wpa_ctrl_open: Success
-/bin/sh: Failed: not found
CST-BUERO:/# Could not read interface wlan0 flags: No such device
-/bin/sh: Could: not found
CST-BUERO:/# Failed to initialize driver interface
-/bin/sh: Failed: not found
CST-BUERO:/# done.
-/bin/sh: done.: not found
CST-BUERO:/# starting /etc/init.d/S52syslogd ...
-/bin/sh: starting: not found
CST-BUERO:/# starting /etc/init.d/S60autofs ...
-/bin/sh: starting: not found
CST-BUERO:/# Jan  1 00:00:30 CST-BUERO syslog.info syslogd started: BusyBox v1.3
0.1
-/bin/sh: Jan: not found
CST-BUERO:/#  1 Jan 00:00:30 ntpdate[1540]: ntpdate 4.2.8p6@1.3265-o (1)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# starting
-/bin/sh: starting: not found
CST-BUERO:/# starting /etc/init.d/S80dvdreadfs ...
-/bin/sh: starting: not found
CST-BUERO:/# starting /etc/init.d/S90inetd ...
-/bin/sh: starting: not found
CST-BUERO:/# starting /etc/init.d/S96nfsd ...
-/bin/sh: starting: not found
CST-BUERO:/# Jan  1 00:00:31 CST-BUERO daemon.notice rpc.statd[1579]: Version 2.
2.1 starting
-/bin/sh: Jan: not found
CST-BUERO:/# Jan  1 00:00:31 CST-BUERO daemon.notice sm-notify[1580]: Version 2.
2.1 starting
-/bin/sh: Jan: not found
CST-BUERO:/# Jan  1 00:00:31 CST-BUERO daemon.notice rpc.statd[1579]: Initializi
ng NSM state
-/bin/sh: Jan: not found
CST-BUERO:/# exportfs: Failed to stat /media/sda1/movies: No such file or direct
ory
-/bin/sh: exportfs:: not found
CST-BUERO:/# Jan  1 00:00:32 CST-BUERO daemon.notice rpc.mountd[1595]: Version 2
.2.1 starting
-/bin/sh: Jan: not found
CST-BUERO:/# starting /var/etc/init.d/S9T_tuxcald ...
-/bin/sh: starting: not found
CST-BUERO:/# starting /var/etc/init.d/S9T_tuxmaild ...
-/bin/sh: starting: not found
CST-BUERO:/# Jan  1 00:00:32 CST-BUERO daemon.info : starting pid 1604, tty '':
'/etc/init.d/start_neutrino'
-/bin/sh: Jan: not found
CST-BUERO:/#
CST-BUERO:/# Please press Enter to activate this console. /var/plugins/operation
s camd_init
-/bin/sh: Please: not found
CST-BUERO:/# /var/plugins/operations cardserver_start
tpdate[1540]: step time server 130.133.1.10 offset 662734547.261081 sec
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter0/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter1/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter2/frontend3: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend0: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend1: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend2: No such file or directory
[frontend.cpp:Open:284] /dev/dvb/adapter3/frontend3: No such file or directory
MON: The POD Monitor task has started. Version = 01, Release = 00, Subrelease = 01, PID: 1640
MON: Initializing
slot->inbound_queue : 76070070
slot->outbound_queue: 7606ff18
xport_command_queue: 7606fd00
MON: Start resource providers...
MON: Starting 9 resource(s).
MON starting 9 resources finished
MON after BR_POD_mon_start_rps
RM: Resource Manager thread started. PID: 1640
XPORT: POD Transport task started. PID: 1640
LINK: POD link task started with arg=0x00000000, PID: 1640
APPINFO thread starts, PID: 1640
CA resource provider started with arg=0x00000000, PID: 1640
CP resource start, PID: 1640
CP thread get delay time 0(s)
CP: Start of initialization...
SYSTIME resource start, PID: 1640
MMI thread is started, PID: 1640
HOSTCTRL thread is started, PID: 1640
HOSTLANG_CNTY thread is started, PID: 1640
UPGRADE thread is started, PID: 1640
APPMMI thread starts, PID: 1640
XPORT: transport connection #1 set to Idle
comming in  add resource provider, rid=10041
POD timer thread PID: 1640
ciappReportModuleStatus: status 9, gCardStatus: 0
PHYS-CI+: cs_ci_init_controller called
LINK: hard reset complete.
LINK: slot #0 state = BR_POD_SLOT_NOT_INIT
comming in  add resource provider, rid=240041
SYSTIME RP: System Time main loop processing started.
comming in  add resource provider, rid=410041
comming in  add resource provider, rid=30041
CA RP: Resource Provider main loop processing started.
RM before wait for db ready, pid: 1640
RM after wait for db ready, pid: 1640
dump mbuf....
LINK: slot #0 state = BR_POD_SLOT_CARD_NOT_PRESENT
LINK: after bypass card
MON after wait event
RM: Resource Manager message processing started.
RM: recvd LINK_STATUS tag(0x42), len=8
APPMMI RP: resource provider is added
APPMMI RP: APPMMI resource provider main loop processing started.
dump mbuf....
Mbuf trace_id: 1640, aux: 0x00000000, freq: 1
ciappReportModuleStatus: status 0, gCardStatus: 0
MON: Wait for all required resource providers to sign on....
comming in  add resource provider, rid=20043
comming in  add resource provider, rid=8d1001
HOSTLANG_CNTY RP: resource provider is added
HOSTLANG_CNTY RP: HOSTLANG_CNTY resource provider main loop processing started.
CP nvram: Root certificate file is for production
RM: No host-pod interface
APPINFO RP: resource provider is added, resource ID :0x20043
APPINFO RP: APPINFO resource provider main loop processing started.
RM: close all connections on slot 0
dump mbuf....
comming in  add resource provider, rid=8e1001
UPGRADE RP: resource provider is added
UPGRADE RP: UPGRADE resource provider main loop processing started.
comming in  add resource provider, rid=200041
HOSTCTRL RP: resource provider is added
HOSTCTRL RP: HOSTCTRL resource provider main loop processing started.
comming in  add resource provider, rid=400/var/plugins/operations cardserver_start
doscam laeuft bereits
CST-BUERO:/# starte doscam

-/bin/sh: starte: not found
CST-BUERO:/# Sat Jan  1 00:00:32 CET 2000
-/bin/sh: Sat: not found
CST-BUERO:/# /var/plugins/operations
/var/plugins/operations
CST-BUERO:/# /var/plugins/operations rezap
/var/plugins/operations rezap
CST-BUERO:/# Sat Jan  1 00:00:33 CET 2000
-/bin/sh: Sat: not found
CST-BUERO:/# 31 Dec 12:56:22 ntpdate[1540]: step time server 130.133.1.10 offset
 662734547.261081 sec
-/bin/sh: 31: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter0/frontend2: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter0/frontend3: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend0: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend1: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend2: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter1/frontend3: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend0: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend1: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend2: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter2/frontend3: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend0: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend1: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend2: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# [frontend.cpp:Open:284] /dev/dvb/adapter3/frontend3: No such file o
r directory
-/bin/sh: [frontend.cpp:Open:284]: not found
CST-BUERO:/# MON: The POD Monitor task has started. Version = 01, Release = 00,
Subrelease = 01, PID: 1640
-/bin/sh: MON:: not found
CST-BUERO:/# MON: Initializing
-/bin/sh: MON:: not found
CST-BUERO:/# slot->inbound_queue : 76070070
-/bin/sh: slot-: not found
CST-BUERO:/# slot->outbound_queue: 7606ff18
-/bin/sh: slot-: not found
CST-BUERO:/# xport_command_queue: 7606fd00
-/bin/sh: xport_command_queue:: not found
CST-BUERO:/# MON: Start resource providers...
-/bin/sh: MON:: not found
CST-BUERO:/# MON: Starting 9 resource(s).
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# MON starting 9 resources finished
-/bin/sh: MON: not found
CST-BUERO:/# MON after BR_POD_mon_start_rps
-/bin/sh: MON: not found
CST-BUERO:/# RM: Resource Manager thread started. PID: 1640
-/bin/sh: RM:: not found
CST-BUERO:/# XPORT: POD Transport task started. PID: 1640
-/bin/sh: XPORT:: not found
CST-BUERO:/# LINK: POD link task started with arg=0x00000000, PID: 1640
-/bin/sh: LINK:: not found
CST-BUERO:/# APPINFO thread starts, PID: 1640
-/bin/sh: APPINFO: not found
CST-BUERO:/# CA resource provider started with arg=0x00000000, PID: 1640
-/bin/sh: CA: not found
CST-BUERO:/# CP resource start, PID: 1640
-/bin/sh: CP: not found
CST-BUERO:/# CP thread get delay time 0(s)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# CP: Start of initialization...
-/bin/sh: CP:: not found
CST-BUERO:/# SYSTIME resource start, PID: 1640
-/bin/sh: SYSTIME: not found
CST-BUERO:/# MMI thread is started, PID: 1640
-/bin/sh: MMI: not found
CST-BUERO:/# HOSTCTRL thread is started, PID: 1640
-/bin/sh: HOSTCTRL: not found
CST-BUERO:/# HOSTLANG_CNTY thread is started, PID: 1640
-/bin/sh: HOSTLANG_CNTY: not found
CST-BUERO:/# UPGRADE thread is started, PID: 1640
-/bin/sh: UPGRADE: not found
CST-BUERO:/# APPMMI thread starts, PID: 1640
-/bin/sh: APPMMI: not found
CST-BUERO:/# XPORT: transport connection #1 set to Idle
-/bin/sh: XPORT:: not found
CST-BUERO:/# comming in  add resource provider, rid=10041
-/bin/sh: comming: not found
CST-BUERO:/# POD timer thread PID: 1640
-/bin/sh: POD: not found
CST-BUERO:/# ciappReportModuleStatus: status 9, gCardStatus: 0
-/bin/sh: ciappReportModuleStatus:: not found
CST-BUERO:/# PHYS-CI+: cs_ci_init_controller called
-/bin/sh: PHYS-CI+:: not found
CST-BUERO:/# LINK: hard reset complete.
-/bin/sh: LINK:: not found
CST-BUERO:/# LINK: slot #0 state = BR_POD_SLOT_NOT_INIT
-/bin/sh: LINK:: not found
CST-BUERO:/# comming in  add resource provider, rid=240041
-/bin/sh: comming: not found
CST-BUERO:/# SYSTIME RP: System Time main loop processing started.
-/bin/sh: SYSTIME: not found
CST-BUERO:/# comming in  add resource provider, rid=410041
-/bin/sh: comming: not found
CST-BUERO:/# comming in  add resource provider, rid=30041
-/bin/sh: comming: not found
CST-BUERO:/# CA RP: Resource Provider main loop processing started.
-/bin/sh: CA: not found
CST-BUERO:/# RM before wait for db ready, pid: 1640
-/bin/sh: RM: not found
CST-BUERO:/# RM after wait for db ready, pid: 1640
-/bin/sh: RM: not found
CST-BUERO:/# dump mbuf....
-/bin/sh: dump: not found
CST-BUERO:/# LINK: slot #0 state = BR_POD_SLOT_CARD_NOT_PRESENT
-/bin/sh: LINK:: not found
CST-BUERO:/# LINK: after bypass card
-/bin/sh: LINK:: not found
CST-BUERO:/# MON after wait event
-/bin/sh: MON: not found
CST-BUERO:/# RM: Resource Manager message processing started.
-/bin/sh: RM:: not found
CST-BUERO:/# RM: recvd LINK_STATUS tag(0x42), len=8
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# APPMMI RP: resource provider is added
-/bin/sh: APPMMI: not found
CST-BUERO:/# APPMMI RP: APPMMI resource provider main loop processing started.
-/bin/sh: APPMMI: not found
CST-BUERO:/# dump mbuf....
-/bin/sh: dump: not found
CST-BUERO:/# Mbuf trace_id: 1640, aux: 0x00000000, freq: 1
-/bin/sh: Mbuf: not found
CST-BUERO:/# ciappReportModuleStatus: status 0, gCardStatus: 0
-/bin/sh: ciappReportModuleStatus:: not found
CST-BUERO:/# MON: Wait for all required resource providers to sign on....
-/bin/sh: MON:: not found
CST-BUERO:/# comming in  add resource provider, rid=20043
-/bin/sh: comming: not found
CST-BUERO:/# comming in  add resource provider, rid=8d1001
-/bin/sh: comming: not found
CST-BUERO:/# HOSTLANG_CNTY RP: resource provider is added
-/bin/sh: HOSTLANG_CNTY: not found
CST-BUERO:/# HOSTLANG_CNTY RP: HOSTLANG_CNTY resource provider main loop process
ing started.
-/bin/sh: HOSTLANG_CNTY: not found
CST-BUERO:/# CP nvram: Root certificate file is for production
-/bin/sh: CP: not found
CST-BUERO:/# RM: No host-pod interface
-/bin/sh: RM:: not found
CST-BUERO:/# APPINFO RP: resource provider is added, resource ID :0x20043
-/bin/sh: APPINFO: not found
CST-BUERO:/# APPINFO RP: APPINFO resource provider main loop processing started.
-/bin/sh: APPINFO: not found
CST-BUERO:/# RM: close all connections on slot 0
-/bin/sh: RM:: not found
CST-BUERO:/# dump mbuf....
-/bin/sh: dump: not found
CST-BUERO:/# comming in  add resource provider, rid=8e1001
-/bin/sh: comming: not found
CST-BUERO:/# UPGRADE RP: resource provider is added
-/bin/sh: UPGRADE: not found
CST-BUERO:/# UPGRADE RP: UPGRADE resource provider main loop processing started.
-/bin/sh: UPGRADE: not found
CST-BUERO:/# comming in  add resource provider, rid=200041
-/bin/sh: comming: not found
CST-BUERO:/# HOSTCTRL RP: resource provider is added
-/bin/sh: HOSTCTRL: not found
CST-BUERO:/# HOSTCTRL RP: HOSTCTRL resource provider main loop processing starte
d.
-/bin/sh: HOSTCTRL: not found
CST-BUERO:/# comming in  add resource provider, rid=400041
-/bin/sh: comming: not found
43), len=8
CP RP: resource provider is added
CP: Resource Provider main loop processing started.
2020-12-31 12:56:30.466 [sectionsd] start
2020-12-31 12:56:30.601 [sectionsd] starting
2020-12-31 12:56:30.639 [sectionsd] timeThread::run:: starting, pid 1640 (1671562416)
2020-12-31 12:56:30.644 [sectionsd] eitThread::run:: starting, pid 1640 (1669465264)
2020-12-31 12:56:30.716 [sectionsd] cnThread::run:: starting, pid 1640 (1667368112)
2020-12-31 12:56:30.742 [sectionsd] freeSatThread::run:: starting, pid 1640 (1665270960)
2020-12-31 12:56:30.747 [sectionsd] timeThread: get DVB time ch 0x000000000000 (isOpen 1)
[ConfigFile] Unable to open file /var/tuxbox/config/bookmarks for reading.
2020-12-31 12:56:31.422 [sectionsd] timeThread: get DVB time ch 0x000000000000 rc: 8 neutrino_sets_time 0
2020-12-31 12:56:31.432 [sectionsd] SIsectionTIME::parse: TDT time: Thu Dec 31 12:56:27 2020
2020-12-31 12:56:31.436 [sectionsd] timeThread: timediff -4436229, current: 31.12.2020 12:56:31, dvb: Thu Dec 31 12:56:27 2020

2020-12-31 12:56:27.000 2020-12-31 12:56:27.005 2020-12-31 12:56:27.005 [sectionsd] freeSatThread::run:: time set: Thu Dec 31 12:56:27 2020

2020-12-31 12:56:27.006 [sectionsd] cnThread::run:: time set: 2:56:27 2020

[sectionsd] eitThread::run:: time set: Thu Dec 31 12:56:27 2020

[sectionsd] timeThread: Time set via DVB (TDT), going to sleep for 5 seconds.
2020-12-31 12:56:27.582 [sectionsd] commandserviceStopped
2020-12-31 12:56:27.702 [sectionsd] cnThread: stop eit update filter (not active)
2020-12-31 12:56:27.705 2020-12-31 12:56:27.708 [sectionsd] cnThread::shouldSleep first retry (1) -> restart demux
[sectionsd] commandserviceStopped done
2020-12-31 12:56:27.743 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
sh: you need to specify whom to kill
2020-12-31 12:56:28.089 [sectionsd] timeThread: get DVB time ch 0x00030085002b (isOpen 1)
2020-12-31 12:56:28.193 [sectionsd] addEvent: ch 00030085002b running 4 (curr) got_CN 0
2020-12-31 12:56:29.095 [sectionsd] addEvent: ch 00030085002b running 0 (next) got_CN 1
2020-12-31 12:56:29.715 [sectionsd] cnThread: eit update filter, ch 0x00030085002b, current ver 0x12  got events 3 (not active)
2020-12-31 12:56:30.102 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
2020-12-31 12:56:30.152 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
2020-12-31 12:56:30.434 [sectionsd] timeThread: get DVB time ch 0x00030085002b rc: 29 neutrino_sets_time 0
2020-12-31 12:56:30.444 [sectionsd] SIsectionTIME::parse: TOT time: Thu Dec 31 12:56:30 2020
2020-12-31 12:56:30.448 [sectionsd] timeThread: timediff -448256, current: 31.12.2020 12:56:30, dvb: Thu Dec 31 12:56:30 2020

2020-12-31 12:56:30.459 [sectionsd] difference is < 120s, using adjtime(0, -448256). oldd(0, 0)
2020-12-31 12:56:30.472 [sectionsd] timeThread: Time set via DVB (TOT), going to sleep for 1800 seconds.
[operations] rezap...
2020-12-31 12:56:35.829 [sectionsd] commandserviceChanged: Service change to 47b100030085002b demux #0
Dec 31 12:56:50 CST-BUERO local0.info xupnpd[1814]: ./plugins/xupnpd_youtube.lua:158: bad argument #1 to 'decode' (string expected, got nil)
2020-12-31 12:56:50.862 [sectionsd] commandserviceChanged: Service change to 46712720f001c36f demux #2
2020-12-31 12:57:07.464 [sectionsd] commandserviceChanged: Service change to 4a31000400850197 demux #2
2020-12-31 12:57:30.312 [sectionsd] commandserviceChanged: Service change to 4b71000100850017 demux #2
CST-BUERO:/# MMI RP: re
-/bin/sh: MMI: not found
CST-BUERO:/# MMI RP: MMI resource provide.
-/bin/sh: MMI: not found
CST-BUERO:/# no CICAM brand id extension.
-/bin/sh: no: not found
CST-BUERO:/# comming in  add resource provider, rid=8c1001
-/bin/sh: comming: not found
CST-BUERO:/# RM: recvd RM_RESOURCES_CHANGED tag(0x43), len=8
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# CP RP: resource provider is added
-/bin/sh: CP: not found
CST-BUERO:/# CP: Resource Provider main loop processing started.
-/bin/sh: CP:: not found
CST-BUERO:/# 2020-12-31 12:56:30.466 [sectionsd] start
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:30.601 [sectionsd] starting
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:30.639 [sectionsd] timeThread::run:: starting, pid
 1640 (1671562416)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:30.644 [sectionsd] eitThread::run:: starting, pid
1640 (1669465264)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:30.716 [sectionsd] cnThread::run:: starting, pid 1
640 (1667368112)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:30.742 [sectionsd] freeSatThread::run:: starting,
pid 1640 (1665270960)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:30.747 [sectionsd] timeThread: get DVB time ch 0x0
00000000000 (isOpen 1)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [ConfigFile] Unable to open file /var/tuxbox/config/bookmarks for r
eading.
-/bin/sh: [ConfigFile]: not found
CST-BUERO:/# 2020-12-31 12:56:31.422 [sectionsd] timeThread: get DVB time ch 0x0
00000000000 rc: 8 neutrino_sets_time 0
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:31.432 [sectionsd] SIsectionTIME::parse: TDT time:
 Thu Dec 31 12:56:27 2020
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:31.436 [sectionsd] timeThread: timediff -4436229,
current: 31.12.2020 12:56:31, dvb: Thu Dec 31 12:56:27 2020
-/bin/sh: 2020-12-31: not found
CST-BUERO:/#
CST-BUERO:/# 2020-12-31 12:56:27.000 2020-12-31 12:56:27.005 2020-12-31 12:56:27
.005 [sectionsd] freeSatThread::run:: time set: Thu Dec 31 12:56:27 2020
-/bin/sh: 2020-12-31: not found
CST-BUERO:/#
CST-BUERO:/# 2020-12-31 12:56:27.006 [sectionsd] cnThread::run:: time set: 2:56:
27 2020
-/bin/sh: 2020-12-31: not found
CST-BUERO:/#
CST-BUERO:/# [sectionsd] eitThread::run:: time set: Thu Dec 31 12:56:27 2020
-/bin/sh: [sectionsd]: not found
CST-BUERO:/#
CST-BUERO:/# [sectionsd] timeThread: Time set via DVB (TDT), going to sleep for
5 seconds.
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:27.582 [sectionsd] commandserviceStopped
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:27.702 [sectionsd] cnThread: stop eit update filte
r (not active)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:27.705 2020-12-31 12:56:27.708 [sectionsd] cnThrea
d::shouldSleep first retry (1) -> restart demux
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [sectionsd] commandserviceStopped done
-/bin/sh: [sectionsd]: not found
CST-BUERO:/# 2020-12-31 12:56:27.743 [sectionsd] commandserviceChanged: Service
change to 47b100030085002b demux #0
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# sh: you need to specify whom to kill
-/bin/sh: sh:: not found
CST-BUERO:/# 2020-12-31 12:56:28.089 [sectionsd] timeThread: get DVB time ch 0x0
0030085002b (isOpen 1)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:28.193 [sectionsd] addEvent: ch 00030085002b runni
ng 4 (curr) got_CN 0
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:29.095 [sectionsd] addEvent: ch 00030085002b runni
ng 0 (next) got_CN 1
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:29.715 [sectionsd] cnThread: eit update filter, ch
 0x00030085002b, current ver 0x12  got events 3 (not active)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:30.102 [sectionsd] commandserviceChanged: Service
change to 47b100030085002b demux #0
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:30.152 [sectionsd] commandserviceChanged: Service
change to 47b100030085002b demux #0
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:30.434 [sectionsd] timeThread: get DVB time ch 0x0
0030085002b rc: 29 neutrino_sets_time 0
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:30.444 [sectionsd] SIsectionTIME::parse: TOT time:
 Thu Dec 31 12:56:30 2020
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:56:30.448 [sectionsd] timeThread: timediff -448256, c
urrent: 31.12.2020 12:56:30, dvb: Thu Dec 31 12:56:30 2020
-/bin/sh: 2020-12-31: not found
CST-BUERO:/#
CST-BUERO:/# 2020-12-31 12:56:30.459 [sectionsd] difference is < 120s, using adj
time(0, -448256). oldd(0, 0)
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# 2020-12-31 12:56:30.472 [sectionsd] timeThread: Time set via DVB (T
OT), going to sleep for 1800 seconds.
-/bin/sh: syntax error: unexpected "("
CST-BUERO:/# [operations] rezap...
-/bin/sh: [operations]: not found
CST-BUERO:/# 2020-12-31 12:56:35.829 [sectionsd] commandserviceChanged: Service
change to 47b100030085002b demux #0
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# Dec 31 12:56:50 CST-BUERO local0.info xupnpd[1814]: ./plugins/xupnp
d_youtube.lua:158: bad argument #1 to 'decode' (string expected, got nil)
-/bin/sh: Dec: not found
CST-BUERO:/# 2020-12-31 12:56:50.862 [sectionsd] commandserviceChanged: Service
change to 46712720f001c36f demux #2
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:57:07.464 [sectionsd] commandserviceChanged: Service
change to 4a31000400850197 demux #2
-/bin/sh: 2020-12-31: not found
CST-BUERO:/# 2020-12-31 12:57:30.312 [sectionsd] commandserviceChanged: Service
change to 4b71000100850017 demux #2
-/bin/sh: 2020-12-31: not found
CST-BUERO:/#

 

 

Link zu diesem Kommentar
Auf anderen Seiten teilen

  • Admin

Aus meiner Sicht ist das kein sauberer Boot der Box aber da ich die NEO² nicht habe kann ich das nicht testen daher auch nur eine Empfehlung.

Ich würde ein neues Image flashen ohne Übernahme der Settings, alles neu einrichten und dann nochmal testen.

 

Das Log zeigt Fehler beim NAND Device

*** Warning - bad CRC or SFC, using default environment
| 00000000*| 1FFFFFFF*| NAND    | Toshiba NAND 512MiB 3,3V 8-bit    

[    0.931064] NAND device: Manufacturer ID: 0x98, Chip ID: 0xdc (Toshiba NAND 512MiB 3,3V 8-bit), 512MiB, page size: 2048, OOB size: 64
[    0.943464] Bad block table found at page 262080, version 0x01
[    0.949976] Bad block table found at page 262016, version 0x01
[    0.956233] nand_read_bbt: bad block at 0x00001cf60000

 

Link zu diesem Kommentar
Auf anderen Seiten teilen

Gesagt getan!

 

Wollte dann das das Image V 3.92 nochmal aufspielen!

Im Ergebnis ist die Box dann im Sartbild hängen geblieben. :-(!

 

Also habe ich dann von der Coolstream Site

 

http://www.coolstream.to/index.php?page=Thread&threadID=15584

 

Das Emergency Tool und Update gewagt! Mit USB Stick!

 

Das hat auch funktioniert.

Nur leider komme ich im Nachgang nicht mehr das Keywelt drauf ohne das ich im Startbildschirm wieder hängen bleibe!

Das mit V3.92 und 4.12b!

 

Woran liegt das denn jetzt?

 

 

Link zu diesem Kommentar
Auf anderen Seiten teilen

Hi,

die Zee² hat ja zwei getrennte Anschlüsse für die beiden Tuner, wie hast du die miteinander verbunden (kurzes Kabel) ? Tausche die beiden Anschlüsse mal und teste neu. Hinweis: manchmal reicht schon ein kleines bischen drehen des Steckers vom Kabel und der Empfang wird besser oder auch schlechter, ist schon manchmal komisch... ;)

 

Ciao,

DdD.

Link zu diesem Kommentar
Auf anderen Seiten teilen

Also habe bei Empfehlungen mal genutzt!

 

1. DdD =habe mal die Eingänge und das kurze Kabel getauscht!

-> Auch keine Besserung bzw. anderes Ergebnis!

2. topie88 = In den Informationen taucht immer nur ein Tuner auf! T1 und oder T2!

-> Das scheibt aber normal!

    

Einstellungen:

a) Tuner 1 = Independent

     Tuner 2 = Independent

      Aufnahme von Sky geht auf Tuner 1!

      Beim Umschalten sehe ich auch alle anderen Kanäle in der Auswahlübersicht!

      Einige sind dann zu sehen!

           Beispiel ZDF Top Bild Tuner 2!

           ARD Bildfehler auch auf Tuner 2!

           Pro7 Top Bild auch auf Tuner 2!

 

b) Tuner 1 = nicht genutzt

     Tuner 2 = Independent

      Keine - Aufnahme!

      Tuner 1 nicht aktiv!

           ARD Bildfehler auch auf Tuner 2!

           ZDF Top Bild auf Tuner 2!

           Pro7 Top Bild auch auf Tuner 2!

           Sat1 Kein Bild auf Tuner 2!

 

c) Tuner 1 = Independent

     Tuner 2 = nicht genutzt

      Aufnahme von Sky geht auf Tuner 1!

      Kein anderer Kanal ist auszuwählen.

      Ohne Aufnahme sind aber alle Programme mit Top Bild!

 

 

Diagnose! Tuner 2 in dutten! Oder?

 

 

 

 

 

Link zu diesem Kommentar
Auf anderen Seiten teilen

tausch mal die eingänge der antenne wenn es 2 eingänge sind

also zieh kabel aus 1 raus und steck die mal an tuner 2  ob dann ard ohne ruckeln geht

 

lass alle tuner auf indepent stehn

-----

 

nach meiner meinung ist entweder tuner 2 defekt  oder das signal was bei 2 rein geht ist auf einigen Transponder gestört, zu schwach etc

bearbeitet von thomasrichter
Link zu diesem Kommentar
Auf anderen Seiten teilen

  • 11 months later...

Hallo zusammen,

ich habe auch alle Probleme mit der Zee² (Kabel) gehabt, beim flaschen hängenbleiben, egal ob aus dem tmp, vom Stick oder online,--
Tuner Probleme, (im Wohnzimmer läuft irgendein Programm, über Kodi streamen im Büro geht, aber umschalten auf ein anderes Programm beeinflusst wieder das Wohnzimmer,) -- verhalten wie nur 1 Tuner.
Irgendwann habe ich das Original Image über Emergency draufgemacht

dann 3.60 geflasht, nun ging alles (im Tuner Einstellmenü war da plötzlich die Option Twin Tuner, zusätzlich zu Independent)
dann konnte ich problemlos auf 3.92 flashen, ohne das die Zee² dabei hängenblieb

alles funktionierte
Dann habe ich mal im Tuner-Menü auf independent umgestellt...

Kodi Problem wie gehabt

also wollte ich zurück auf Twin-Modus

aber der war weg

dann habe ich wieder das original-Image geflasht

dann 3.60

dann 3.92

nun war twin wieder da und alles rennt prima

meine Meinung ist im 3.92 stimmt was nicht, man sollte vorher 3.60 draufhaben dann ist alles gut

  • Like 1
Link zu diesem Kommentar
Auf anderen Seiten teilen

  • Wer ist Online   0 Benutzer

    • Keine registrierten Benutzer online.
×
×
  • Neu erstellen...