Jump to content

NEO² startet nicht - immer wieder Boot Kernel > u-boot

wutz65

Von wutz65
in Allgemein

 Share

Empfohlene Beiträge

wutz65

wutz65

Geschrieben
Geschrieben

Meine Neo2 mit Netzschalter startet ständig neu in der Anzeige kommt Boot Kernel und dann wieder Neustart

 

nach der Anleitung mtd2 und mtd3 aufgespielt

 

http://www.keywelt-board.com/index.php?/topic/163189-coolstream-neo-repair-anleitung/

 

Auf dem Board steht HD.102.07-S  2011.11.28

 

Netzteil wurde schon von einer gleichen Coolstream getestet.

 

das kommt an der COM-Schnittstelle

 

▒ Vendor: Conexant  Type: CX2450x (Nevis)  Revision: D0       Fuses: 7EFE6D24  ▒
▒ Option: 00010000  max. clock: 600 MHz    Core voltage: high                  ▒
▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒͹
▒ Clock information                                                            ▒
▒ MPG0: 594.000 MHz  MPG1: 594.000 MHz  HD  : 593.407 MHz  AUD : 491.520 MHz   ▒
▒ PLL0: 432.000 MHz  PLL1: 594.000 MHz  PLL2: 533.333 MHz                      ▒
▒ CPU : 594.000 MHz from PLL1                                                  ▒
▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒͹
▒ Memory configuration                                                         ▒
▒ Start    ▒ End      ▒ Type  ▒ Description                                    ▒
▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ĺ
▒ 00000000 ▒ 0FFFFFFF ▒ RAM   ▒ System main memory bank #0                     ▒
▒ 10000000 ▒ 17FFFFFF ▒ RAM   ▒ System main memory bank #1                     ▒
▒ F0000000 ▒ F1FFFFFF ▒ FLASH ▒ Spansion S29GL256P (256 Mbit / 16M x 16)       ▒
▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒͹
▒ Serial number: 008-00012763 (08-0031DB)                                      ▒
▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒͹
▒ Network configuration                                                        ▒
▒ MAC: Conexant VMAC rev. 07       address: 00-C5-5C-00-31-DB                  ▒
▒ PHY: IC Plus IP101               address: 09                                 ▒
Error: Bad gzipped data
Error: no valid bmp or bmp.gz image at f0060000
▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ͼ
Hit any key to stop autoboot:  1
 

ist da noch was zu retten?

Link zu diesem Kommentar
Auf anderen Seiten teilen
wutz65

wutz65

Geschrieben
  • Autor
Geschrieben (bearbeitet)

Mehrfach geflasht über USB-Update zuletzt das Image aus dem NXPHDloader

 

Hab mal den Tuner ausagebaut und bekomme folgendes LOG - am Ende immer Neustart

 

 

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2016.08.30 09:00:54 =~=~=~=~=~=~=~=~=~=~=~=


[2h[61"p[m[44m[37m[1m[2J[1;1H[(B[)B[?3l[?9hÉÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ»

º U-Boot 2009.03-svn1773 (Nov 02 2010 - 15:25:47)     Coolstream HDx           º

ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹

º Chipset information                                                          º

º Vendor: Conexant  Type: CX2450x (Nevis)  Revision: D0       Fuses: 7EFE6D24  º

º Option: 00010000  max. clock: 600 MHz    Core voltage: high                  º

ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹

º Clock information                                                            º

º MPG0: 594.000 MHz  MPG1: 594.000 MHz  HD  : 593.407 MHz  AUD : 491.520 MHz   º

º PLL0: 432.000 MHz  PLL1: 594.000 MHz  PLL2: 533.333 MHz                      º

º CPU : 594.000 MHz from PLL1                                                  º

ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹

º Memory configuration                                                         º

º Start    ³ End      ³ Type  ³ Description                                    º

ºÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄĺ

º 00000000 ³ 0FFFFFFF ³ RAM   ³ System main memory bank #0                     º

º 10000000 ³ 17FFFFFF ³ RAM   ³ System main memory bank #1                     º

º F0000000 ³ F1FFFFFF ³ FLASH ³ Spansion S29GL256P (256 Mbit / 16M x 16)       º

ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹

º Serial number: 008-00012763 (08-0031DB)                                      º

ÌÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͹

º Network configuration                                                        º

º MAC: Conexant VMAC rev. 07       address: 00-C5-5C-00-31-DB                  º

º PHY: IC Plus IP101               address: 09                                 º

Error: Bad gzipped data

Error: no valid bmp or bmp.gz image at f0060000

ÈÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍͼ

Hit any key to stop autoboot:  1  0 

## Booting kernel from Legacy Image at f0080000 ...

   Image Name:   Coolstream HD1 Kernel

   Image Type:   ARM Linux Kernel Image (uncompressed)

   Data Size:    3895352 Bytes =  3.7 MB

   Load Address: 17048000

   Entry Point:  17048000

   Verifying Checksum ... OK

   Loading Kernel Image ... OK

OK



Starting kernel ...



Linux version 2.6.26.8-nevis (stanley@localhost.localdomain) (gcc version 4.3.2 (crosstool-NG-1.3.2) ) #1 Wed Aug 5 07:15:46 CEST 2009

CPU: ARMv6-compatible processor [410fb764] revision 4 (ARMv7), cr=00c5387f

Machine: CoolStream HD1 IRD

Memory policy: ECC disabled, Data cache writeback

CPU0: D VIPT write-back cache

CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets

CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 97536

Kernel command line: console=ttyRI0 mtdparts=cx2450xflash:384k(U-Boot)ro,128k(Splash),4096k(kernel),28160k(systemFS) root=mtd3 rootfstype=jffs2 rw mem=384M init=/linuxrc

PID hash table entries: 2048 (order: 11, 8192 bytes)

Console: colour dummy device 80x30

console [ttyRI0] enabled

Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)

Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)

Memory: 384MB = 384MB total

Memory: 385536KB available (3568K code, 351K data, 116K init)

Mount-cache hash table entries: 512

CPU: Testing write buffer coherency: ok

net_namespace: 192 bytes

NET: Registered protocol family 16

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 4096 (order: 2, 16384 bytes)

TCP established hash table entries: 16384 (order: 5, 131072 bytes)

TCP bind hash table entries: 16384 (order: 4, 65536 bytes)

TCP: Hash tables configured (established 16384 bind 16384)

TCP reno registered

NET: Registered protocol family 1

NetWinder Floating Point Emulator V0.97 (double precision)

JFFS2 version 2.2. © 2001-2006 Red Hat, Inc.

SGI XFS with security attributes, no debug enabled

msgmni has been set to 753

io scheduler noop registered

io scheduler anticipatory registered

io scheduler deadline registered

io scheduler cfq registered (default)

ttyRI0 at MMIO 0xe0412000 (irq = 2) is a CX2450x UART

brd: module loaded

loop: module loaded

Inside emacdev_load function

Inside emacdev_init function

EMAC 0 Initialized

Driver 'sd' needs updating - please use bus_type methods

Driver 'sr' needs updating - please use bus_type methods

CX2450x MTD driver v1.0 (Aug  5 2009, 07:12:17) (c) Coolstream International Ltd.

cx2450xflash: Found 1 x16 devices at 0x0 in 16-bit bank

 Amd/Fujitsu Extended Query Table at 0x0040

cx2450xflash: CFI does not contain boot bank location. Assuming top.

number of CFI chips: 1

cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.

4 cmdlinepart partitions found on MTD device cx2450xflash

Creating 4 MTD partitions on "cx2450xflash":

0x00000000-0x00060000 : "U-Boot"

0x00060000-0x00080000 : "Splash"

0x00080000-0x00480000 : "kernel"

0x00480000-0x02000000 : "systemFS"

cx2450x-ehci cx2450x-ehci.0: Conexant CX2450X EHCI USB-Controller

cx2450x-ehci cx2450x-ehci.0: new USB bus registered, assigned bus number 1

cx2450x-ehci cx2450x-ehci.0: irq 13, io mem 0xe8000100

cx2450x-ehci cx2450x-ehci.0: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

usb usb1: Product: Conexant CX2450X EHCI USB-Controller

usb usb1: Manufacturer: Linux 2.6.26.8-nevis ehci_hcd

usb usb1: SerialNumber: cx2450x-ehci.0

Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

mice: PS/2 mouse device common for all mice

i2c /dev entries driver

TCP cubic registered

NET: Registered protocol family 17

NET: Registered protocol family 15

RPC: Registered udp transport module.

RPC: Registered tcp transport module.

VFS: Mounted root (jffs2 filesystem).

Freeing init memory: 116K

Failed to execute /linuxrc.  Attempting defaults...

mount: Mounting /dev/sda1 on /media/sda1 failed: No such file or directory

mount: Mounting /dev/sdb1 on /media/sdb1 failed: No such file or directory

info, udhcpc (v1.2.0) started

debug, Sending discover...

debug, Sending select for 192.168.120.67...

info, Lease of 192.168.120.67 obtained, lease time 864000

deleting routers

route: SIOC[ADD|DEL]RT: No such process

adding dns 192.168.120.1

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: remove, product: (null), interface: (null)

insmod: cannot insert `/lib/modules/2.6.26.8-nevis/cs_frontpanel.ko': No such device (-1): No such device

/dev/display: No such device or address

/dev/display: No such device or address

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: misc, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: bus, action: add, product: (null), interface: (null)

HOTPLUG: source: drivers, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: drivers, action: add, product: (null), interface: (null)

HOTPLUG: source: drivers, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: i2c-adapter, action: add, product: (null), interface: (null)

HOTPLUG: source: i2c-dev, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: class, action: add, product: (null), interface: (null)

HOTPLUG: source: module, action: add, product: (null), interface: (null)

HOTPLUG: source: platform, action: add, product: (null), interface: (null)

HOTPLUG: source: drivers, action: add, product: (null), interface: (null)

HOTPLUG: source: dvb, action: add, product: (null), interface: (null)

HOTPLUG: source: dvb, action: add, product: (null), interface: (null)

HOTPLUG: source: dvb, action: add, product: (null), interface: (null)

HOTPLUG: source: drivers, action: add, product: (null), interface: (null)

/dev/display: No such device or address

HOTPLUG: source: module, action: add, product: (null), interface: (null)

 

bearbeitet von Markham
Spoiler gesetzt
Link zu diesem Kommentar
Auf anderen Seiten teilen
  • Admin
SnowHead

SnowHead

Geschrieben
  • Admin
Geschrieben

@wutz65

 

Also mit ausgebautem Tuner würde ich nun nicht gerade versuchen, eine Box zu reflashen. Man weiß dann

am Ende gar nicht, warum es nicht funktioniert.

 

Mich irritiert die Ausschrift "Machine: CoolStream HD1 IRD" in Deinem Log. Entweder hast Du den falschen

Kernel (bei mir kommt "Machine: CoolStream HDx IRD"), das würde erklären, warum er den Frontprozessor

nicht initialisieren kann 

insmod: cannot insert `/lib/modules/2.6.26.8-nevis/cs_frontpanel.ko': No such device (-1): No such device")

oder der Frontprozessor ist hinüber.

 

Wie sieht das Log mit den Files aus der von mir verlinkten Anleitung aus? Und funktioniert der Flashen über-

haupt? Was wird während des Flashens auf dem Display angezeigt?

 

Link zu diesem Kommentar
Auf anderen Seiten teilen
  • 2 months later...
 Share
Gehe zur Themenübersicht

  • Wer ist Online   0 Benutzer

    • Keine registrierten Benutzer online.
×
×
  • Neu erstellen...